Question about Jura Capresso Impressa E75 Espresso & Coffee Maker

1 Answer

Malfunction light on Jura E75

After I turn on unit it flashes "please wait' for a couple of minutes then switces to "malfunction 5" or possibly it says "malfunction E".

Prior to the problem I had cleaned the water tray. I also pressed the rinse buttom a couple of times then used the frother. The frother seemed to overheat and steam emerged from the top of the unit. I then shut the unit off to cool. After that couldn't restart without the problem noted above.

Posted by on

  • Anonymous Mar 18, 2014

    My Jura keeps saying please wait and does not go to the second step of 'rinse unit'

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I just called the company with the same problem today. They will fix your machine for free. They have recalled this machine. Call them and they will tell you what to do. 201-767-3999

Posted on Mar 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have just purchased Jura machine and set up. I pressed rotary switch and it says on display machine filling. then it stops like its meant to and says press rotary switch. I press it and instaed of r


Hi Jon, I'm Joel, Is this machine you have for a restaurant or private use. a friend bought a machine like this at Bed Bath & Beyond and his machine had a problem with the rinsing cycle and beyond, this machine has a motherboard inside just like a computer and it should have a reset button underneath it or in the back or it's possible that the motherboard is bad. To recycle the motherboard hit the reset button and wait till the machine to finish rebooting and pull the plug and wait about 5 minutes, if this doesn't work then you need to take back to the store for a replacement or refund, If you ask me I would rather have a refund because this particular machine always goes into a malfunction mode. This is one of the newer model so unfortunately the company didn't have time to get all the kinks out. Hope this helps....Joel

Oct 25, 2014 | Jura Impressa J9 Automatic Coffee Center

2 Answers

Error 4


Unfortunately the error message 5 indicates that the thermal block and/or thermal sensor and possibly a control board need to be tested, and likely one or more, possibly all, replaced. My recommendation is to send it to Capresso ask what it will cost first. M

Aug 11, 2014 | Jura Capresso Impressa Z5 Espresso/Coffee...

1 Answer

Display tap on Jura Impressa E75 say close tap, where is tap please


The tap is the dial on the left turn it, then it will turn the tap off. If it is repeating this then it may need to be decalcified.

Sep 06, 2012 | Jura Capresso Impressa E75 Espresso &...

1 Answer

How to fix error message 8


DISPLAY SHOWS MALFUNCTION 8 Solution: Turn off and unplug machine. Wait a minute. Turn machine on and wait until it stops making any noise. Now try to pull out the drawer. If this does not work, try the procedure again. If this does not work, call customer service
Regards Kat (please leave feedback, many thanks)

Aug 19, 2011 | Jura Capresso Impressa E8 Espresso/Coffee...

2 Answers

Impressa S70 - Malfunction 3


This indicates that either the sensor for the thermoblock is defective or the thermofuse is blown. For this you need to go to your local dealer for service. I also recommend that you measure out the mains.
In worst case the powerprint or the mainboard sends wrong signals to the thermoblock so it`s overheated.

Aug 02, 2009 | Jura Capresso Impressa E8 Espresso/Coffee...

2 Answers

Jura impressa E75.message mafunction 8 shows up


Malfunction 8 is related to the brew unit typically. It is usually an indication of the brew unit motor having to work too hard to move the brew unit up and down. This is usually cured by disassembling, cleaning, replacing any o'rings that may be bad, and lubricating the unit, then reassembly.
I have had to do this twice on an an E75 and an E8. I finally broke down and bought seal kits and lubricant for doing this. One could by a new brew unit off of e-bay and change out the whole thing. But a simple rebuild will typically suffice.

Mike

Aug 12, 2008 | Jura Capresso Impressa E75 Espresso &...

1 Answer

Jura Capresso Problem


check out this link:
http://www.kuntze.de/E/index.htm

May 12, 2007 | Jura Capresso Impressa E75 Espresso &...

Not finding what you are looking for?
Jura Capresso Impressa E75 Espresso & Coffee Maker Logo

359 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jura Capresso Coffee Makers & Espresso Machines Experts

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

The Knight
The Knight

Level 3 Expert

68323 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Jura Capresso Coffee Maker and Espresso Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...