Question about Sony FD Trinitron WEGA KV-36XBR800 36" TV
A little while ago, and suddenly, the color would go to only shades of green and gray when switched from high def to regular tv. The only way to fix it was to turn set off then back on. Then started getting occasional flashes of orange and set would turn off. Then today, the set won't turn on at all. The standby light flashes but doesn't sound like has enough juice when you go to turn it on. HELP!
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
go to this website:
hope this will help yah!!
Posted on Jan 30, 2008
check for an open resistor on the power supply, it is actually a fusible resistor, (white) if open, then check the converter, some sets have two separate and some have it as one. it will be on a heat sink on the power supply. if shorted then check for a shorted horizontal output transistor and repair cold solder joints on the horizintal drive transformer which is the real cause of this problem
Posted on Jan 08, 2009
U check the power source?Take the tv aparts,check or replaced the power fuse,might get lucky.Not,than sorry,this tv can't be repair,without replacing electronic's componnents parts.Hire the same shop to do the repair.Ur tv power ICS inverter are dead.
Posted on Jun 15, 2010
Your power supply board is dead, do you know basic electronics' and soldering? Most of the times, the power supply board just have dead leakages gases capacitors.These capacitors always bulges up on it top,or puff up on it top.Replaced these gases leakages capacitors will get your TV power stable,and work again.Or tries websites like Shopjimmy.com,Ebay.com to buy a whole refurbish power supply board for the replacement.
I hope this will help in solving the problem..
Posted on Aug 05, 2011
Tips for a great answer:
Feb 12, 2010 | Samsung HLR5067WX 50" Rear Projection HDTV
May 27, 2008 | Sharp Televison & Video
Nov 20, 2009 | Sony KDS-R60XBR1 60" Projection HDTV
May 30, 2009 | Samsung HL-R6167W 61" HDTV
Dec 30, 2008 | NEC WT610 DLP Projector
Aug 23, 2017 | Sony WEGA KD-34XBR970 34" TV
Dec 30, 2007 | LG Flatron 295LM 22" LCD Monitor
You have a problem with the three factors, and they are screen voltage, focus voltage, and control (focus 2) voltage. Basically these voltages have to be adjusted since the components in this section have aged some. These controls are usually located in the television on the IHVT (Integrated High Voltage Transformer) or as it is also called the flyback transformer. these controls must be adjusted together, along with the color controls. Here is how the adjustment is done (You will need a schematic diagram, a DC volt meter, and a color bar generator to do these measurments):
1) turn color and tint fully counter clockwise until you have a black and white picture.
2) connect the color bar generator to the TV (ch 3) and turn it on, you should see bars in various shades of gray
3) adjust as best as possible the color and tint controls to obtain the color bars on the screen Red Green Blue.
4) measure the voltages on the focus, screen and control grids of the CRT and match them to the schematic digram measurements.
5) adjust the focus screen and control grids to match the ones on the schematic diagram
6) once this is done then you adjust the color controls once again to obtain the red green and blue bars on the TV screen.
This should help if the CRT (picture tube) electron guns are still good and if the flyback transformer voltage supply is working.
However if you do not have a background in electronics please take the TV to a shop for repairs.
I hope this helps,
Oct 16, 2007 | Sony KV-20M20 20" TV
86 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: