Question about Computers & Internet

1 Answer

Geometry A rope is connected to aboat and the boat' anchor that is resting on the ocean floor at a position not directly under the boat. The rope is 100 feet long and the water is 50 feet deep. To the nearest tenth of a foot, how far is the anchor from a point directly below the boat?

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert who has written 7 tips or uploaded 3 video tips


    An expert who has written 3 tips or uploaded 2 video tips.

  • Expert
  • 58 Answers

I don't understand how this relate to Ecommerce Websites, but here is the answer:

The answer is the root of a
root of 7500 is 86.6025403784439

Posted on Nov 18, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Why does my depth reading suddenly change in the middle of the ocean

If the sudden changes occures while the boat is plning, the changes are due to the passing of disturbet, turbulent, air bubbled water under the boat.
If they happen while the boat is still, probabily you detect some fish or other sea-life...

Sep 30, 2017 | Ocean Boating

1 Answer

Where is the serial number located on my 13 foot - 1976boston whaler boat?

I have a 2014 Boston Whaler 15 Super Sport and a 1986 SuperSport 15 before it :>)

There are two numbers. One is in the rope/anchor locker at the bow of the boat engraved on a riveted aluminium plaque. This is the identification and mold number done by Boston Whaler which also dates the boat if you write in to BW..

There is often a second number engraved into the starboard stern of the boat just above the waterline. I think this is a government registration number.

Can I suggest you bookmark this site

and also the Boston Whaler Facebook page. It is run very well by a guy called Jeff Rohlfling. The knowledge there is incredible, whether it is engines, props, paint or models, plus fab pictures of Boston Whalers in their natural habitat. Everything from 13s to the other night at 45 foot Conquest with 4 engines totalling 1,400hp!

Jun 27, 2017 | Boating

1 Answer

Steering on starcraft fishing boat

Some one has assembled the rack to the wrong side of the steering wheel shaft, OR put the cable down the wrong side of the boat, OR switched from a pivot steering anchor to a transom mount anchor (you would have had a drag link left over.)

Jul 11, 2012 | Light Boating

1 Answer

An easy way to install the starter

Hello, I learned a trick from putting in a boat starter on a cabin cruiser. Not sure it will help you, but here it is. I used a rope around the starter to hold it up while I tried to start a guide bolt in. It took enough weight off the starter for me to get a bolt started.

Once I had 1 bolt started, it carried the weight and I could juggle the starter into position. On my boat, I used the exhaust manifold to tie off one end of the rope. You may have to back off a transmission bell housing bolt to do the same.

Or you may be able to wedge a piece of wood from the floor to under the starter to help with alignment and weight. You may need enough extensions to reach from the bolt on the starter to the front of the engine, about 36 inches.

Be sure to position your wheels to allow for clearance under the starter, as tierods can get in the way.

Feb 23, 2011 | 2001 Ford Explorer Sport Trac

1 Answer

My pcb board was unfortunately touched by soltwater [canon mf 4122]

If I had a nickel for every one that I've told not to take their printer to the beach, or not to take it fishing in the ocean, I'd be rich.
Salt water is very corrosive. So take your printer this one time out on your boat and toss it overboard. If you tie a rope to it you could have an anchor.

Dec 21, 2010 | Office Equipment & Supplies

1 Answer

Need to replace my fuel line from my gas tank to my outboard engine.The tank runs under the floor & the length of the boat 17ft.any help or suggestion will be welcomed

attach a small rope to one end and pull the old line out reuse the rope to pull new line in and reattach at both ends

Oct 26, 2010 | Boating

1 Answer

Motor is dead

wrap a rope around its leg and throw it off the back-make sure you hold onto rope tightly-you now own a new anchor! lol

Jul 12, 2009 | Boating

1 Answer

Sprint 600 Vertical Windlass blows fuse

Is this the main fuse???
600watts motor on a 12V system drops 50amps...
You should have an 80 or even 100 amps fuse for the power cables!

Jun 15, 2017 | Boating

1 Answer

Wiring two circuit pull switch boat lights

3 terminals.. 1 power input & 2 x outputs

Main positive goes to 1 terminal = power in to switch.

The anchor goes to another terminal = power out from switch to anchor

3rd terminal is another output for lights/anchor.


Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

163 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18425 Answers

Alun Cox

Level 3 Expert

2678 Answers

David Payne
David Payne

Level 3 Expert

14162 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides