Question about E-Machines eMachines Desktop PC

1 Answer

Emachine t2542 i have an emachine t2542 and the wires from the front panel are out do you have a diagram of the motherboard to replace the power button, and the front blinking light wires back on to the motherboard thank you sue

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,992 Answers

When you say out, do you mean they are broken, or just disconnected? Most of these computers have a plug on the end of the wires to the front panel and it just plugs into the system board. If you look at the board you'll see where the front panel wires go. Sometimes it's hard to read the small type, but there are labels on the board that tell you what connector does what.

Posted on Nov 20, 2008

  • Bob Farley
    Bob Farley Apr 02, 2014

    There is no indication of where these wires go. It is a bunch of numbers and does not indicate power, reset, speakers or anything else.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Motherboard diagram Acer eMachine MB DA061/078L


Hello? Tap, tap on the monitor. What are you reading from?

http://www.ebay.com/itm/Acer-MB-NB107-001-DA061-078L-Motherboard-eMachines-08120-2-780G-AM2-Desktop-/280919767281?pt=Motherboards&hash=item41681f78f1

The front of your computer is the Front Panel.
The area of contact pins on the motherboard, that the main wires go to from the Front panel, is the Front panel header.

Motherboard installed in computer, the Front panel header is at the Bottom/Right.
Two rows of 7 pins in a small black rectangular plastic block.

http://www.ebay.com/itm/Acer-DA061-078L-Motherboard-eMachines-EL1200-X1200-AMD-780G-Socket-AM2-DDR2-/140825131784?pt=Motherboards&hash=item20c9d4fb08

TOP row of pins is numbered EVEN.
BOTTOM row of pins is numbered ODD.

Starting on the LEFT side going towards the Right, TOP row:
Pins 2, 4, 6, 8, (NO 10), 12, and 14. Again, there is NO Pin 10.

Starting on the LEFT side going towards the Right, BOTTOM row;
Pins 1, 3, 5, 7, 9, 11, and 13.

A) Pins 1 and 3 are for the HarDDrive activity LED. (Light)
Pin 1 is for the Positive ( + ) wire.
If the HDD LED is dim when the harddrive is active, switch the wires around.

2) Pins 5 and 7 are for a Reset switch, IF a Reset switch is used.

3) Pins 2 and 4 are for the Power On LED (Light)
Pin 2 is for the Positive ( + ) wire.
If the PWR LED is dim when the computer is on, switch the wires around.

4) Pins 6 and 8 are for the Power On switch.

5) The rest of the pins are N/C. Not Connected.

Don't forget to plug the 4-pin ATX +12 Volt power cable in,
(Top left corner),

http://www.playtool.com/pages/psuconnectors/connectors.html#atx12v4

For additional questions please post in a Comment.

Regards,
joecoolvette

Sep 06, 2012 | PC Desktops

1 Answer

Emachine w3107 wiring diagram


Good luck on finding a wiring diagram. Usually those plugs represent the Power Button, the Hard Drive and the other sometimes represents a reset button. If you remove the cover and sit the computer on it's side, take a flashlight so you can see inside at the motherboard. If you look from where the wires come from on the front they usually stick into little prongs on the side of the motherboard. The motherboard will have little written identifiers such as hdd for the hard drive light, pwr for power or power reset, fan for fan, etc.

Also sometimes if you look on the little piece at the end of the red, white and black wires where it plugs into the motherboard prongs, sometimes it will have writing on it as to which one it is.

Mar 24, 2012 | PC Desktops

1 Answer

How to hook up the face plate of a emachine w3400 Wich includes 3 wires 1 power butten and 2 led lights


Look at the pinout of the Front Panel header, of the eMachine W3400's motherboard.

The plastic front of the computer is the Front Panel.
The area of pins on the motherboard, that the cables (Wires) from the Front Panel connect to,
is the Front Panel header.

The motherboard for an eMachines W3400 desktop computer is an MSI ms-7145
(Micro Star International)

Orient the motherboard in your view so that we are both looking at it the same way.
Processor to the Top, Ram Memory slots to the Right, white PCI slots (3) to the Bottom.

JFP1 is the Front Panel header.
(Junction Front Panel 1)

JFP1 is on the Bottom Right corner. There are two columns of pins arranged vertically.
(The JFP1 header runs parallel to the Right side of the motherboard)

The Left side column of the JFP1 header is numbered Odd.
Starting at the Top and going Down, the pins are numbered;
1, 3, 5, 7, and 9

The Right side column is numbered Even.
Starting at the Top and going Down, the pins are numbered:
2, 4, 6, and 8.
There is NO Pin 10

A) Pins 1 and 3 are for the HarDDrive Activity LED light. (HDD)
If the LED light is dim will operating switch the wires around

B) Pins 5 and 7 are for the Reset switch. (Reset button)
> IF Used

C) Pin 9 is Not used. (NC. No Connection)

D) Pins 2 and 4 are for the Power On LED light (If dim switch the wires around)

E) Pins 6 and 8 are for the Power On switch. (Power On button)

Trace the wires back to the Power On switch. Even if it means temporarily removing part of the Front Panel to see.

Same with the LED lights.
See which wires go to the Power On LED, and HDD Activity LED. (Harddrive Activity LED)

Follow the 3 wires, and tell me where they go to on the Front Panel.
USB port?
Memory Card Reader?
Firewire port? (a1394)

Nov 27, 2010 | AMD eMachines Desktop System w/ 17'' CRT...

1 Answer

Need wiring connection diagram for Power Switch to Motherboard for EMachine W2925 model. Wires were disconected accidentally while cleaning inside of tower


micha219, the eMachines W2925 desktop computer uses an FIC motherboard.
First International Computer { Inc }
The Model Number of the FIC motherboard is VC37.
FIC VC37.

Disregard the following if you are aware:
The plastic front of your computer is the Front Panel.
The area on the Motherboard that the cables (Wires) from the Front Panel connect to, is the Front Panel header.

Processor to the Top, Ram Memory slots to the Right, the Front panel header is in the Bottom Right corner.

It is a rectangular shape with two columns of pins.
The length goes up, and down on the motherboard.

The pins on the Right side of the Front Panel header are numbered Odd.
The pins on the Left side of the Front Panel header are numbered Even.

There are 4 pins on the Left side.
There are 5 pins on the Right side.

Starting at the Bottom on the Right side going Up;
Pins 1, 3, 5, 7, and 9.

Starting at the Bottom on the Left side going Up;
Pins 2, 4, 6, and 8.

A) Pins 2 and 4 are for the Power On LED light.
(If after connecting the LED light is dim, reverse the wires)

B) Pins 6 and 8 are for the Power On switch. (Power On button)

C) Pins 1 and 3 are for the HarDDrive Activity LED light.

D) Pins 5 and 7 are for the Reset switch. (Reset button. IF used)

Pin 9 is NC. Not connected

Oct 18, 2010 | E-Machines eMachines Desktop PC

1 Answer

Front power switch broken. Bezel won't come off easily. Thought we could just get a switch and install on the back but don't know which of the colored pairs of wires go to the original switch in the...


I would suggest this generic Power On switch,

1) http://www.directron.com/atxswitch.html,

and the Red, and Black twisted pair of wires go to the Power On switch.

Your statement of ,"....don't know which of the colored pairs of wires go.....", leads me to believe you may have all of the Front Panel wires disconnected.

How about information as to where ALL the Front Panel wires go?
(Provided I have correctly interpreted your statement)

Back in the time that the eMachines T2542 was made, TriGem was the motherboard manufacturer.

The Model Name of the motherboard is Imperial, and the Model Number of the motherboard, could have been one of four variations offered.

Model Name: Imperial
Model numbers could be G, GL, GV, or GLVE
(Imperial G, Imperial GL, Imperial GV, or Imperial GLVE)

ALL four variations used the same Front Panel header.
(The connector on the motherboard the Front Panel wires connect to, is named the Front Panel header)

I would like you to view this page,

http://www.e4allupgraders.info/dir1/ecase/support/front_panel_header_support.shtml

Scroll down to the heading -
Trigem Imperial Front Panel Header Pinout.

A) Pins 1, 2, and 3 are for the Power On LED light.

B) Pins 5 and 6 are for the HarDDrive activity LED light.
(Pin 4 is not used. NC. No Connection)

C) Pins 7 and 8 are for the Power On switch

D) I wouldn't connect any wires to Pins 9 and 10, nor Pins 11 and 12

E) Pins 14 and 15 are for the Reset switch. (The button you press to restart your computer.
If the T2542 doesn't have a Reset switch, don't worry about it. There are many other ways to restart your computer)

F) Pins 17 18, and 20 are for an internal speaker.
This speaker is used for BIOS Beep Codes.

In the chart to the right, you will see GRD used many times.
GRD stands for Ground.
ANY Black wire in the twisted pair of wires, is a Ground wire.

Most of the eMachines I have worked on, use a Red, and Black pair of twisted wires for the Power On switch.
I could be mistaken on the T2542.

Best method, is to follow the color code of the wires that come from Pins 7 and 8, and be sure.

Aug 17, 2010 | E-Machines T2542 PC Desktop

1 Answer

I just lost all my cd 's with my emachine t2542,i re install new W XP OS because my hard disk was damaged and replace new one,the problem is,it's usb ports doesn't work,help me pls.tnx


In order for us to assess possible drivers that are available for the eMachines T-Series T2542, please download the trial of Driver Detective and run it to ensure a more accurate list of drivers for your computer with less chance of error.
http://www.drivershq.com/Drivers/eMachines/T-Series/T2542/22605/22647/22688/Drivers.aspx

Oct 05, 2009 | E-Machines T2542 PC Desktop

1 Answer

Emachines t3830 I need the schematic for MB I umployed the wire for the push bottom without looking at the way they were plug. Now I do not know the correct aligning of the push bottom wires.


If you look at the motherboard there is usually a diagram labeled "FRONT PANEL HDR" that will tell you which pins are for: HDD LED, PWR LED, RESET, PWR ON. etc.
The chart / diagram may be a few inches away from front panel header.
the following example is from my emachine T2893 that I had opened because it won't power up.

the motherboard at the header connector labels pin #2 and with that you can figure out the other
pin numbers

example of diagram on motherboard (Confirm the pin numbers on your motherboard)


J9G1 PINS
| HD LED | 1 - 3 |
| PWR LED | 2 - 4 |
| RESET | 5 - 7 |

| PWR ON | 6 - 8 |

Hope this helps you figure which pins to hook you switch up to.

Jan 18, 2009 | E-Machines eMachines T3830 PC Desktop

3 Answers

Connect wires to the motherboard


Please tell me the model number then I will be able to help you.

Nov 14, 2008 | E-Machines eMachines Desktop PC

2 Answers

Emachine flashing yellow lights, fans power up when P8 is unplugged


Did some research and found this site which will tell you which pins to test. It is possible also that its not powerful enough for the devices you have. I would try again only giving power to the motherboard pins, of coarse and the hard drive. If works then plug one device at a time.
Good luck

http://articles.techrepublic.com.com/5100-10878_11-1046822.html

Jul 05, 2008 | E-Machines eMachines Desktop PC

Not finding what you are looking for?
E-Machines eMachines Desktop PC Logo

Related Topics:

339 people viewed this question

Ask a Question

Usually answered in minutes!

Top E-Machines PC Desktops Experts

joecoolvette
joecoolvette

Level 3 Expert

5660 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3051 Answers

Are you an E-Machines PC Desktop Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...