Question about Cisco WS-X4548-GB-RJ45V= Expansion Module

1 Answer

Problem with module WS-X4548-GB-RJ45V in Catalyst 4506

Help me please. We are buy new module WS-X4548-GB-RJ45V for our Cisco Catalyst 4506. And IOS write us what this module is unsupported. Attache include image.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 39 Answers

Use software advisor in Cisco website to verify it.just follow the process.

console to it and show diag and see whether it detectable or not.

hope this help.

Posted on Sep 11, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Do I need to buy a software license for WS-C2960S-48FPS-L?


No. WS C2960S 48FPS uses the Universal image, but no license is required. The feature is bound to the hardware model type and cannot be changed. For convenience, a single software image is used for all Cisco Catalyst 2960-S Series Switches, regardless of whether they are a LAN Base or LAN Lite model.

Jan 20, 2015 | Cisco Catalyst 2960 Ethernet Switch ...

1 Answer

WS-X45-SUP6L-E Led is not coming to green


If you have two SUP's this one will be in standby mode.

Mar 10, 2012 | Cisco Computers & Internet

1 Answer

Need to replace the Chassis of CISCO 4500 switch. Can i know Step by Step procedure to do this change.


http://www.cisco.com/en/US/docs/switches/lan/catalyst4500/hardware/installation/guide/78-14409-08/04replac.html.......................... please follow the above link

Feb 11, 2011 | Cisco Catalyst 4506-E Cat4500 E-series...

1 Answer

I just replaced cisco 4506 with new 4506-e, the uplink port didn't work for trunking


Hi, if you installed a Supervisor 6L-E 10GE (X2) in the new 4506-E and you want to use the two 10GE uplinks as Gigabit, you need to type in the following config lines:

hw-module module 1 port-group 1 select gigabitethernet
hw-module module 1 port-group 2 select gigabitethernet

Jan 17, 2011 | Cisco Catalyst 4506-E Cat4500 E-series...

1 Answer

Hello, I tried the steps you have mentioned in the link below: http://www.fixya.com/support/t3932749-password_recovery_cisco_catalyst_4506 and the other similar resolutions on the cisco website but...


Please make sure you have only one supervisor module installed on your switch or else pull out the backup sup module and do this activity .

In the last step of reset it will ask to save the config.

do you wish to save this configuration? y/n [n]: y
You must reset or power cycle for new configuration to take effect

do not forget to type in y there.

Jan 01, 2011 | Cisco Catalyst 4506-E Cat4500 E-series...

1 Answer

Dear Sir I have a CISCO WS-C2948G-L3 switch with me, when I power it up I get the following message :- ROMMON: Cold Reset frame @0x00000000 ROMMON: Reading reset reason register ROMMON: Valid...


It looks like the IOS is bad or not not there.
You need to instal a new IOS onto the switch.


For more help during installation you can refer
http://www.cisco.com/en/US/products/hw/switches/ps663/products_tech_note09186a00800949c3.shtml#cat4k

Dec 09, 2010 | Cisco WS-C2948G-L3 Catalyst 2948G-L3...

1 Answer

How to speed changed in gigabitEthernet 2/1 from cisco 4506switch


Hi

Ok so once you have logged into the router you do the following

go into enable mode by tyoing in en
Then type in conf t
then type in int X where X = the interface
then type in speed 100
then type end

This will set the interface to 100mbps

Feb 27, 2010 | Cisco Catalyst 4506-E Cat4500 E-series...

1 Answer

Password Recovery for Cisco Catalyst 4506


Please see Cisco's page at http://www.cisco.com/en/US/products/hw/routers/ps5199/products_password_recovery09186a0080093e12.shtml
for step by step details and more in depth instruction.

1. Reboot
2. Press the "break" button on your keyboard within 60 seconds of the power-up to put the router into ROMMON mode.
3. confreg 0x2142
4. reset
5. type, "no" when prompted to enter the initial configuration dialog.
6. enable
7. copy startup-config running-config
8. conf t
9. enable secret <password>
11. config-register 0x2102
12. reboot again

Jan 20, 2010 | Cisco Catalyst 4506-E Cat4500 E-series...

Not finding what you are looking for?
Cisco WS-X4548-GB-RJ45V= Expansion Module Logo

Related Topics:

549 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cisco Computers & Internet Experts

Gopi Venkatesan
Gopi Venkatesan

Level 2 Expert

74 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Prashant M
Prashant M

Level 3 Expert

2263 Answers

Are you a Cisco Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...