Question about Husqvarna Rose

1 Answer

My Rose 605 blows the overload motor fuse.

I have replaced it serveral times but it blew it again. My husband cleaned it really good. First it starts by breaking the needles and then it just stops. What it sews, it sews good. I have not even been able to try the embroidery part. Any suggestions? Thanks. Denalilady

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I finally fixed this machine. What was wrong was the PC board. It was very expensive to fix. Over $500.

Posted on Jun 06, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi Ive a brother innov-is 90e Embroidery machine carriage got dirty and rusted now skips stitches


Be sure you are using a brand new needle. Otherwise, I would start with the timing. Search for:

sewing machine timing

Lots of web sites and videos that may help you narrow down the issue.

Feb 11, 2018 | Brother Sewing Machines

1 Answer

Can the needle position be changed on the Rose 600 model; if yes, how?


Below is a link to a manual for the 605 which is probably pretty close to your machine. Look at page 39:

Husqvarna Rose 605 User Manual

Nov 16, 2017 | Sewing Machines

1 Answer

Janome MB4 wont sew breaks threads really bad?


1--thread breaks really easy if it is a couple of months old
may be new to you but in the shop for a long time
2---thread breaks easy if the incorrect needle eye size is used for the thread thicjness
3-- thread breaks easy in the needle tension is incorrect
4-- thread breaks easy if the needle is threaded from the wrong side ( look for a small groove down the back of the needle and thread from that side so the thread sits in that groove )
5-- thread breaks easy if the needle /hook timing is a bit out as the hook pierces the thread instead of picking it up cleanly from the recessed section at the eye

find another repair shop because if the dealer couldn't fix it under warranty, they sure cannot fix it when out of warranty and for money

Aug 06, 2017 | Janome MB4 Four Needle Embroidery Machine

1 Answer

My Husqvarna diamond top thread keeps breaking while doing loop embroidery. It sews a couple of stitches and then you can hear when the thread breaks. Ive tried changing the needle and bobbin, and cleaning...


Hello

Primary causes of upper thread breakage:


-- misthreading: pull all the thread off and thread again, using the manual, step by step. Read each step aloud before you do it. (sounds dumb, but helps.) (And make sure you thread the takeup lever!)

-- thread has wrapped itself around a thread guide or spool pin from one of the breaks. Take the spool off the machine before rethreading.

-- bad or damaged needle. Replace with the right size for the fabric, turned correctly (backwards needles skip stitches)

-- dirty machine, especially in the bobbin case area: review cleaning instructions and do it, using brush and vacuum only

-- bad/cheap thread: should not be slubby or break easy. Try another spool.

-- top thread tension too tight. 4 is normal for most fabrics, most stitches.

Tips;

1) do a light cleaning (brush and vacuum) every day you sit down to sew.

2) replace the needle if you hear it hit metal, if you've got a really bad thread jam, if you see it deflect as you sew (for instance, sewing over the side seam on jeans when hemming). Replace every 3-8 hours of actual stitching time anyhow.

3) buy good quality thread

4) when your machine isn't sewing right, stop; take all the thread off of/out of the machine (bobbin out of bobbin case, spool off spool pin) and give it a quick cleaning. Rethread from scratch, carefully. If that doesn't fix it, do it again, then replace needle and rethread one more time, manual in hand (yah, even if you've threaded it 8 million times before). #4 is curative about 98% of the time. The other 2% often requires professional attention.

Jul 11, 2011 | Husqvarna Designer I

1 Answer

My singer curvy 8780 has a timing issue the needle is scraping on the bobbin casement and will not sew,cleaned and oiled, changed needle turned off and on. any suggestions?


Good day!

please try this simple tips:

Good day!

A sewing machine operator can often help themselves when their machine does not operate properly.
Here are some simple instructions, which if properly used can save time and mechanics service calls.
TROUBLE;UPPER THREAD KEEPS BREAKING;
This could be trouble;================Do this;
1.Top tension to tight================loosen tension 1 turn
2.Machine improperly threaded=========check threading
3.Thread twisted on guide post========"
4.Thread twisted out of tension======="
5.Take up spring bent or broken=======Check action of spring
6.Thread jumped off pull off finger===Check threading
7.Needle bent or burred===============new needle
8.Bad cone of thread==================try another cone
TROUBLE;LOWER THREAD KEEPS BREAKING;
1.Bobbin tensionspring to tight=======Loosen tension slightly
2.Bobbin threaded wrong===============check threading
3.Bobbin wound to tight or uneven=====try new bobbin
4.lint or thread on bobbin case=======clean inside case
5.Lint or thread inside hook==========clean inside hook
6.Bobbin case nicked bent or burred===check/change case
TROUBLE;MACHINE STARTED SKIPPING STITCHES;
1.Needle bent or burred===============change
2.Needle set in crooked===============Check
3.Thread jumped off take up spring====check threading
4.Thread jumped off pull off finger===check threading
TROUBLE STITCHES SHOWING LOOPS;
1.Forming loops on top of cloth=======Tighten bobbin tension
======================================or loosen top tension.
2.forming loops on bottom of cloth====Tighten top tension
3.Bobbin placed in case incorrectly===remove and replace
4.Bobbin thread slipped from under====check threading of
tension===============================bobbin case
5.Lint or thread in top tension=======clean between tension discs


Thank you and good luck.

Jun 06, 2011 | Singer Curvy 8770 Electronic Sewing...

1 Answer

My Husqvarna Rose is dead. My husband tried to replace the bulb and it was the wrong one and it wont turn on at all. IS this too a fuse. Where is the fuse on these machines


You can check inside the power supply unit for a fuse, but I think he probably blew a voltage regulator and the power supply will need to be replaced. Contact an authorized Husqvarna Viking repair center.

Dec 13, 2010 | Husqvarna Viking 1

2 Answers

I bought a Husqvarna Rose at a yard sale. The lady told me she used it only a few times because the thread broke icon always pops up and she has to start over again. I tried it and sure enough it stitches...


Hi. You need to start with getting the manual for your machine. I found one at http://www.sewingpartsonline.com/instruction-book-viking-605-sewing-machine-instruction-manual.aspx.

Then, check the threading diagrams to make absolutely sure it's threaded properly. Check the troubleshooting section of the manual.

Hope this helps!

Robbie

Jul 24, 2010 | Husqvarna Rose

2 Answers

Howdy and help !! my 1974 singer genie sewing machine was workin just fine... i broke a needle replaced it with the correct needle inserted properly nothin bent etc and yes - its all threaded properly too....


This can happen to ANY sewer, of any skill level, so don't feel bad.
First, remove the bobbin and bobbin case. Thoroughly clean the area where the bobbin case sits in the machine. Lint builds up here and causes a host of irritating problems. It should be cleaned out often, every few hours of sew time if you're using fuzzy or soft fabrics.

Then, try a newly wound bobbin. Even if it's not the one you wish to use, the one you've got now may have something wrong, be poorly wound perhaps. You can rewind it if need be, or wind another one. Then, rethread the upper machine too. Sometimes you can miss the simplest thing especially if you're not very familiar with the machine. Check every thread guide to be sure no thread has been caught. My old machine has a nick in one guide that catches thread now and then, just have to watch out for it.

Once it's all clean and rethreaded, insert another new needle, and then try to pick up the bobbin thread again and hopefully, all will be well.

I know that needles can be a bit costly, but the least defect in any needle can cause issues, and it's not worth driving yourself nuts over them. Dull needles may not work properly, and many modern fabrics are really, really ******* needles. Best to replace them more often and be sure they're in top notch shape. I don't keep old needles around at all, I put them into the metal recycling so I don't mix them up with new needles. Good luck

Nov 28, 2017 | Sewing Machines

1 Answer

Husqvarna Rose Embroidery Unit problem


Call Viking direct

440-808-6550
800-358-0001

Aug 20, 2009 | Husqvarna Rose

Not finding what you are looking for?
Sewing Machines Logo

Related Topics:

550 people viewed this question

Ask a Question

Usually answered in minutes!

Top Husqvarna Sewing Machines Experts

Douglas Plant
Douglas Plant

Level 2 Expert

194 Answers

Tally Girl
Tally Girl

Level 3 Expert

1133 Answers

Wayne Fellows
Wayne Fellows

Level 2 Expert

262 Answers

Are you a Husqvarna Sewing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...