Question about Mitsubishi Diamond WD-65831 65" Projection HDTV

1 Answer

Mitsu DLP 65831 won't power up

This set was working fine till this am. My daughter turned it on an it didn't start. I went over and tried with the same results. Press the power button, light turns green, there is a faint clicking/popping noise, and a fan starts and stops, this goes on for a couple of min and then the set powers off. No message no picture, nothing. I unplugged for a few mins them tried again, same results. Last year I had a problem with a loose wire on a heat sensor by the bulb. This beamed to be a common problem and the fix was to reseat the connecter for the sensor. This time nothing... Any help would be greatly appreciated.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 108 Answers

Check the lamp

Posted on Jan 10, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I reset tv it's dark and now it wont turn on its a mitsubishi DLP tv


Good day!!!


That problem is not fixed by resetting of unit..

That problem is usually cause of faulty light engine..Try to replace it with the part # (part number usually indicated on the engine itself printed in sticker)..

Hope it helps..

Dec 14, 2011 | Mitsubishi Diamond WD-65831 65" Projection...

1 Answer

Both headlamps won't come on on 06 Touareg. dash light says check headlamps. is it possible that both of them could go out at same time? I'm sure it's quite expensive to repair or replace.


It is very possible you could've running with one burned out for a while and didn't notice uad a power serge or it's possible you have been running with one out for a while and didn't notice till the other went out. Try turning on the high beems if they work replace the bulbs..

Jul 16, 2011 | 2006 Volkswagen Touareg

1 Answer

My car was running fine yesterday and this morning it didn't start. got a new battery, replaced the oil and checked the fuses. everything is fine but car still won't start. suggestions, please


Check for spark and fuel. When you turn the key on you should hear the fuel pump in the tank for a few seconds till the pressure builds up. When you crank the engine there should be spark at the plugs.

Jun 05, 2011 | 2003 Toyota Highlander

1 Answer

I have a 65 inch mitsu DLP, replaced the bulb 6 months ago.. Worked fine until this week.. Now the TV will power up, turn on, then show a picture for a second then go black.. It repeats this nonstop.. ...


Sounds like the Lamp is over temperature. Either the fan went out or the filter is clogged! You might check the filter first. I hope this will help you...

Jan 07, 2011 | Mitsubishi Televison & Video

1 Answer

I have a 2005 52 inch Mitsu turn it on and it goes to red light


di you replace the power for the lamp in your manul it will show you the lite set for your tv it it will give you i ideal what wrong. i see so with bad power supply or
the balstor go bad to i chang lamp bastor frist. when
the lamp go bad it will show you it the lamp in front of dlp. i hope this help you out.

Dec 07, 2009 | Mitsubishi WD-52525 52" Rear Projection...

1 Answer

The input function is not working and the t.v. is on but no picture. Blank screen. Was working last night just fine we tried to hook up Xbox and when the input button was pressed screen went blank. any...


Perform Reset From Front panel of Tv, wait until green light stops blinking, set is running self diagnostic. If that doesn't work, it could be something in the DMD Panel containing the Digital Micromirror Device

Oct 10, 2009 | Mitsubishi Diamond WD-65831 65" Projection...

1 Answer

I have a 61" samsung dlp. It worked fine


Start with replacing the lamp. Then move on to the Ballast. Then the color wheel. Then the Power Supply. One of those parts should fix it. If not call back.

Jul 15, 2009 | Samsung DLP HL-P5663W 56" TV

2 Answers

Samsung dlp


HLS4266W 43" dlp. In less than 1 yr whining grew worse, but did know what it was. Year passed with warranty and lamp went out. Replaced lamp. Worked for 3.5 hrs. Turned on next day and did not work. Got another lamp, but did not work. Figured out might be color wheel. Replaced it too. TV started up. Watched that night. Turned on next day, heard loud pop. Lamp never came on. Withdrew and reinstalled lamp a couple times to see if that worked. Did not. Currently, with new lamp and color wheel installed, lamp light blinks, but no lamp comes on. What now?

Sep 17, 2007 | Samsung HLN5065W 50" Rear Projection...

Not finding what you are looking for?
Mitsubishi Diamond WD-65831 65" Projection HDTV Logo

109 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1207 Answers

The Knight
The Knight

Level 3 Expert

71172 Answers

Jaime Hernandez

Level 3 Expert

2278 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...