Question about Xerox Fax Machines

1 Answer

My IR 400S Photocopier showing E677 after working for 10-15 minutes.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 103 Answers

First Print A configration Page
turn Off Machine

When You Starts A Machine Press Print Button
Wait.....
After That It Asks Run Setup.
Run setup
After That Go TO last Option Restore Default settings.
then ok
wait few menitus
Ins. aal config. in.

Posted on Apr 07, 2009

  • gjckos
    gjckos Oct 02, 2012

    AFTER PRESS OF RUN SETUP THERE IS NO OPTIONS

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kyocera Mita Photocopier KM-1530 Error code AP flashes at start up then C710


When AP flashes the toner is being replenished inside the copier. Wait a few minutes. You need to refill the toner.

Jun 09, 2011 | Fax Machines

1 Answer

Good morning,i have a canon ir 3100c photocopier,which shows an error(E0004).Can u kindly assist me please?


this symptom occurs for the following reasons (3 cases): During transportation, the front panel was held with an excessive force. As a result, the front panel actuator interfered with and detached the front panel sensor . The sensor came in contact with the sensor mount causing 5V line to be short-circuited. If the front panel sensor is damaged, replace it with a new one. At that time, visually inspect the front panel actuator to make sure that it does not interfere with the sensor.
Better contact an authorized service point

Apr 18, 2011 | Fax Machines

2 Answers

Canon ir 2116J shows "System


Very likely the fixing flim is torn.

Feb 18, 2011 | Fax Machines

1 Answer

I need a pdf user manual/repair manual for the Canon Imagerunner 400s copier. Can you email it to me? I changed the toner but the copies are still coming out light with lines. Maybe it's the drum. My...


Hi, Please get your driver here, select your country first before do next step : http://www.canon.com/products/office.html
Other reference website for your canon is here : http://www.freedownloadsarchive.com/c-download/canon-ir-400-copier-user-manual.html

Regars, vote please, Jay

Jan 18, 2011 | Fax Machines

1 Answer

System error 004


E004 Fixing unit failure
E100 Scanner unit failure
E246 The Counter board is left out
E676 Communication error
E677/6F-61 ROM check error
E677/6F-63 RAM error
E733 A fault occurred in the communication between the SCNT board
and ECU board/TOP signal cannot be detected
New E805 Fan failure

TRY THIS:
E004 Fixing unit failure
Cause: (1) Shorted/broken wired main thermistor
(2) Shorted/broken wired sub thermistor
(3) Broken wired heater/blown thermal fuse
Solutions: (1) Turn the power off and remove the fixing unit from the machine.
Measure the resistance between the fixing unit connector J301-1
(FSRTH) and J301-2 (GND).
If the resistance is not within the range between 350 W and 520 W
(room temperature of 20°C), replace the fixing film unit.
(2) Turn the power off and remove the fixing unit from the machine.
Measure the resistance between the fixing unit connector J302-1
(FSRTH2) and J302-2 (GND).
If the resistance is not within the range between 360 W and 530 W
(room temperature of 20°C), replace the fixing film unit.
(3) With the fixing film unit removed, if there is no continuity
between the fixing unit connectors J303-1 (ACN) and J303-3
(ACH), replace the fixing film unit.
(4) Replace the EPU board.
(5) Replace the ECU board.


Jun 24, 2010 | Canon Fax Machines

1 Answer

Photocopier error on Rioch Alicio 3045 model showing a code error of SC545


fuser over heat.U need to take the thermistors out one or two cant remember clean all the hard toner of them.when u put them back in make sure they touch the hot roller firmly.Then touch reset button (yellow rectangle) 1 0 7 then hold cancel button (red) untill screen changes 5/6 sec. turn off then on,should work if not then thermostat possibly blown or fuser laps gone.

Mar 29, 2010 | Fax Machines

1 Answer

Cant find a driver for canon faxphone l75 for vista 64 bit


Canon photocopier IR2016J show error code E007. Please advised me on how to resolve

Jul 10, 2009 | Canon FaxPhone L75 Plain Paper Laser

1 Answer

Error code E007


Canon photocopier IR2016J show error code E007. Please advised me on how to resolve

May 05, 2009 | Fax Machines

4 Answers

Canon NP-2120 copier needs cleaning and service


my photocopier machine is not start properly and the lamp is not working ..

Sep 15, 2008 | Canon Fax Machines

Not finding what you are looking for?
Fax Machines Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Xerox Fax Machines Experts

Whit
Whit

Level 1 Expert

185 Answers

CheckitRight
CheckitRight

Level 3 Expert

1349 Answers

HEMANT GROVER

Level 2 Expert

166 Answers

Are you a Xerox Fax Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...