Question about iLO 2600 Television

7 Answers

Volume/ channel/ remote not working

The volume does not turn up or down and the remote buttons do not work except the power button and the buttons on the tv set dont work except the power volume channel or input do not work if anyone can help solve this it would be appreciated if not. A number for the Ilo company to talk to somebody there.

Posted by on

7 Answers

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 3 Answers
Re: volume/ channel/ remote not working

I just used the following instructions from this site on my 'totally dead' Ilo remote and it worked like a charm! I did step 2 twice on each key and put the batteries back in and it worked great! Hope this helps you too. "Dead" Remotes Can Be Saved How to Re-Start Your "Dead" Remote Control This only takes about a minute and will restart 1 in 3 "Dead" Original Remote Controls. Good Luck! Step 1- Pull the batteries out of the remote and leave them out until Step 4. Step 2- Press and release each and every button one at a time on the remote control until every button has been pressed and released at least once! Step 3- If your remote has slide switches, you must move the switch to each position then repeat the button pushing in Step 2. (When you're done, be sure to put the slide switch in the correct position to operate the unit the remote came with!) Step 4- Put the batteries back into the remote, being very careful to install them correctly. New batteries should be used if you're not sure about the old ones. Step 5- Try the remote. If it works, Great! If not, it's time to call 1-800-Remotes or use this website to order a new remote.

Posted on Jan 23, 2007

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer
Re: volume/ channel/ remote not working

My 26in ilo is stuck on hdmi i cant change the channel or adjust the volume with either the tv or remote can somebody help

Posted on Oct 21, 2008

Re: volume/ channel/ remote not working

The only thing that works on my ilo tv is the power button as well. Whats funny though is you press the power button down and a red light comes on then you have to hit the channel button or volume or source for it to cut on but after it cuts on no other buttons work but the power button. The controller doesnt work either. Its stuck on hdmi.

Posted on Oct 20, 2008

Re: volume/ channel/ remote not working

My Ilo wont work!!!! the remote wont work only the power button does and the buttons on the side of the tv wont work either...only the on and off button...what gives!!! its annoying and I dont know what to do!!!

Posted on Oct 17, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer
Re: volume/ channel/ remote not working

I have the same problem too. e-mail me if someone figures it out.

Posted on Feb 07, 2007

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer
Re: volume/ channel/ remote not working

Dude i have the same problem. if you got it fixed can u e-mail me what to do? i'll give u my e-mail if u repost this. thanks!

Posted on Dec 14, 2006

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer
Re: volume/ channel/ remote not working

I had the same prolem and walmart said only 15 days for returns and the repair service told me at least 2 weeks for someone to look at it. This is my only tv what am I suppose to do?? I took the TV apart and saw no resets or anything like that so I shook the TV I banged in it and still the same thing . I thought maybe one of the buttons were stuck . MY SOLUTION :I HELD THE ON OFF BUTTON ON THE TV(NOT THE REMOTE) AND TO MY SUPRIZE IT WORKED.HOLD THE BUTTON IN FOR AT LEAST 5 MINUTES.

Posted on Mar 10, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

The on / off button on the remote does not work. Will a new remote take care of the problem?

A new remote should. It could either be that the remote is broken or the receiver on the tv. Make sure that the tv works with other buttons such as volume and channel. If everything except the power button on the remote works, just get a new remote.

May 26, 2011 | Flat Panel Televisions

2 Answers

ILO LCD Color HDTV does not change channels / volumn...just turns on/off

The symptoms your TV is experiencing is due to a power supply that is not longer providing the 5 volts properly to the circuitry.
It seems to be a common failure on these TV sets.

Apr 29, 2008 | iLO 3200 32 in. LCD Television

1 Answer

Samsung 40 hd tv the vol will not come down from 100 percent . I try to turn the vol down and it will not turn down. what can I do. tks mike

I presume that the volume will not turn down from either the remote control or the volume buttons on the side of the tv. If the volume down button works on the side of the tv then the remote control is suspect to be faulty. If neither remote or tv volume buttons work then check whether the channel buttons work on the tv (not remote). If none of these work then check the input connection from the buttons /infra red reciver to the main pcb. This is a push on cable connector. As a point, also check that the volume up button on the tv is not stuck in, and feels the same as the other buttons when pressed.

Apr 24, 2010 | Samsung LCD-TV LE40S81B 40 in. HD-Ready...

1 Answer

Dish network code for a viore, volume/power not working

You can power scan for the code.
Turn ON the electronic device you want to program the remote to control.
Press the Mode button( sat,tv,dvd,aux) on the remote until the appropriate mode light is flashing.

Press the Power button. The mode light will stop flashing and stay lit.
Press the Up or Down arrow button to set the remote to the next code. The Down arrow button scans backward and the Up arrow button scans forward.
When the correct code is reached, the device (whether a TV, VCR, or other) will turn off.

Press the pound key button to store the code in the remote control memory. If the code is valid for your remote, the mode light will blink 3 times.
Turn the device back ON by pressing the Power button.
Press sat mode key once you power back on the tv to be able to operate the receiver box.
Try some other functions to make sure you have the correct code. Occasionally the Power button may work when others do not.
If the other buttons work you are finished.

If the other buttons do not work, repeat the previous steps. The scan will resume from the last code stored.
The mode light will flash rapidly when the scan has returned to the starting point and all codes have been tested for that mode. The remote control may not control some device models.

Apr 05, 2010 | Toymax Viore 42 in. Plasma TV

2 Answers

I need to re tune my samsung tv but have no remote any ideas?

you can always use the button on your Tv itself.

ie menu = Menu
Channel up/down = take you up and down
volume = goes left and right.

follow these steps

channel down button to CHANNEL
press the volume button along
channel down button to AUTO STORE
press the volume button to Start the scan.

right now you have your telly tuned in. What you could do it get an old sky remote off a friend/ neighbour. or buy from argos etc ( a lot cheaper then getting a replacement samsung one)

press the following buttons on the sky remote to program it to work with your samsung tv.


try the volume if this works press SELECT to save this code if it doesnt press Tv then try the volume again. repeat this step until the volume works your telly. once it doest dont forget to press the SELECT button to save.

Now you will be able to change your volume use the number keys. if you also press the HELP button on the sky remote this will also change your AV / SOURCE I hope this post helps you out. When it does please leave a thumbs up for me Please

Cheers Little Dish Fitter

Sep 21, 2009 | Samsung LN-S3251D 32 in. LCD HDTV

6 Answers

Panasonic remote and volume/channel buttons do not work

My son put a penny in the SD card slot of my Pansonic flat screen tv. I finally got the penny out but now the volume and tv controls do not work. I can change the channels through my cable box but that is it. The volume does not work on my cable remote or the flatscreen. What do you suggest I do to fix this problem?? Thanks, Josh

Jun 06, 2009 | Panasonic TH-42PX60U Television

1 Answer

No response to any button on remote or tv except power button

Press the 'Favorite' button on the remote. You may have accidentally pressed it. It locks the channel. Pressing again unlocks.

Apr 22, 2009 | iLO 3200 32 in. LCD Television

18 Answers

Vizio remote control not working

Wow, I feel stupid! Solution #2 did it! There are 2 Tv buttons, one on the top right and one on bottom right. You have to press the bottom one!! THANK YOU PPL!!!

Apr 04, 2009 | Vizio VO47L 47 in. LCD TV

1 Answer

Cannot turn tv off with power button or remote , must unplugpower

It could be a stuck button on the set. check to make sure they all feel the same.. If one don't feel right try to free it .. If a button is stuck it wont let any of the others work or the remote.

Mar 29, 2009 | Insignia I-LC23Q1 23 in. HD-Ready LCD...

1 Answer


Hi again,

Many thanks for the wonderful review and the rating.

Good luck and kind regards.

Thank you again for using FixYa.

Nov 07, 2008 | Sharp LC13B6US 13 in. EDTV-Ready LCD...

Not finding what you are looking for?
Flat Panel Televisions Logo

3,970 people viewed this question

Ask a Question

Usually answered in minutes!

Top iLO Flat Panel Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

The Knight
The Knight

Level 3 Expert

66623 Answers

Jim Goldsmith
Jim Goldsmith

Level 3 Expert

1869 Answers

Are you an iLO Flat Panel Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides