Question about Canon Printers & Copiers

2 Answers

Canon copier 3300i error code E000007-0000

I have an error code and need to fix it

Posted by on

  • hpastorius Nov 25, 2008

    error code e000007 what to do??

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 24 Answers

Change the fixing film! It is broken!

Posted on Nov 16, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Thanks How do I fix a broken fixing film

Posted on Nov 17, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to change the toner cartridge on a older copier, a Canon 3300i. i can't figure out how to remove the old toner cartridge.



  • Unplug the unit from the source of electricity. Open the front cover located on the face of the unit.

  • Locate the blue lever in front of the toner cartridge. You will be able to see it clearly when you look through the opening originally covered by the front cover.
  • Pull the blue lever down gently. Do not use force. It is easy to manipulate and just needs a gentle pull.4

  • Look for the blue handle that is on the toner box. Grasp the handle firmly and pull it. The toner box will move toward you. Remove the toner box until it cannot go any farther. The handle is easy to manipulate, so do not tug at it, just pull it gently.
    If you will need more help you can download the service manual for ir 3300i is always good to have a service manual you can download it from the below link:
    http://goo.gl/8glrBm
    Good luck
  • Jul 30, 2013 | Canon imageRUNNER 3300i Printer

    1 Answer

    Where is the waste toner receptacle located on the canon IR 3300i


    Lower rear right portion has a small vertical panel held by one screw. The waste bottle is behind this panel.

    Aug 13, 2009 | Canon imageRUNNER 3300 All-In-One Laser...

    1 Answer

    Error code E000001-0002


    E001
    0000 The main thermistor detects 250°C or higher.
    0001 The main thermistor or the sub
    thermistor detects overheating (hardware
    circuit detection).
    0002 The sub thermistor detects about 295°C or higher.
    Main cause - The fixing film unit is faulty (i.e., the thermistor has a short circuit).

    To clear the error, execute the following in service move:
    COPIER>FUNCTION>CLEAR>ERR.

    Jun 16, 2009 | Canon imageRUNNER 3300i Printer

    1 Answer

    Canon 3300i prints / process very slow


    These machines can print slowly for a varity of reasons. First and foremost is using the incorrect driver. The correct driver can be downloaded here:

    http://www.usa.canon.com/opd/controller?act=OPDSoftwareAct&fcategoryid=2275&modelid=6349

    Also slow printing can be a symtom of a hard drive about to fail (e602 codes).
    Fastest printing speeds can be achieved using the following basic assumptions:
    1) The copier is printing thru a standard cat5 cable; not thru the parallel port.
    2) The network the copier is on is healthy and operating normally.
    3) The network settings on the copier are configured correctly.

    I am a Canon trained authorized tech on these machines and have been working in the field on the ImageRunner 3300 series since their release. I'm not sure if a ram upgrade is available but I haven't installed one in the six plus years of servicing this machine to fix a slow print problem.

    Nov 09, 2008 | Canon imageRUNNER 3300i Printer

    1 Answer

    Canon ir 3300i


    well..those scan settings are on the control software..did you install it?

    www.canon.com will have some options.

    http://tinyurl.com/6qcpgy

    Aug 19, 2008 | Canon imageRUNNER 3300 All-In-One Laser...

    4 Answers

    Reset error codes for Canon imageRUNNER 3300i


    We followed the instructions from your tech. on which buttons to press to get into the menu function and then followed the directions for clearing the error code. After that turned the printer off and back on and the error code reset and the printer worked like a champ.

    Jul 02, 2008 | Canon imageRUNNER 3300 All-In-One Laser...

    2 Answers

    Canon ImageRunner 3300i


    make sure all your cables are connected. i found the first part of the error "E000732" means a communication problem

    Mar 05, 2008 | Canon imageRUNNER 3300 All-In-One Laser...

    Not finding what you are looking for?
    Printers & Copiers Logo

    Related Topics:

    809 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Canon Printers & Copiers Experts

    kakima

    Level 3 Expert

    96417 Answers

    old marine
    old marine

    Level 3 Expert

    1461 Answers

    Donald DCruz
    Donald DCruz

    Level 3 Expert

    17129 Answers

    Are you a Canon Printer and Copier Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...