Question about Kenmore 24 in. 15932 Built-in Dishwasher

1 Answer

Our dishwasher won't advance when it is turned on.

It stays and runs at the initial setting.

Posted by on

  • kathy97267 Nov 17, 2008

    Sorry, I guessed at the make of dishwasher since I wasn't looking at it. It is actually a GE Potscruber 680 and it won't advance beyond the initial setting. It just keeps running in whatever position it is set on.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 833 Answers

Sounds like the timer needs to be changed out.  The motor is defective or the unit is jammed.

Posted on Nov 20, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Frigidaire dishwasher model FDB520RHS2 will not advance pst wash- just keeps washing draining and refilling the wash. does not advance. Left it run for 3 hours, still wash only


We had a problem with our dishwasher, it just went crazy one day and lights would light up but ours did not wash or anything...anyways upon further investigation found out by taking 6 large round head screws off,, the handle and outer cover came off, then there was a cover that was covering a circuit board and this was the brains of the washing machine, ordered the part from sears 160.00 and washer is all set. good luck. oh ya, upon further exam. when I took the board off could see discoloration on part of the circuit board. this means burned out resistor or fuse.

Mar 22, 2014 | Frigidaire Dishwashers

1 Answer

My dishwasher settings are staying on rinse and won't go on anything else


If this is happening with both the drawers then you may need to get the filter board rechecked. Try to turn the mains power off, take power plug out from mains socket and put back in and turn power back on. If no difference then call the technician who replaced the board.
If this problem is with one drawer, then try to clean drawer inside panel with a clean damp cloth and see if you can get the program buttons to work again. If not then a more detailed diagnostics is required.

Mar 23, 2013 | Fisher and Paykel Dishwashers

1 Answer

Frigidaire dishwasher will fill but wont do anything after that, if i hit cancel it will empty, how do i fix that?


If the unit will turn on and fill but won't advance to the next setting/step then either the unit's timer is faulty or it is not communicating correctly with the control board.

Jul 21, 2012 | Frigidaire Dishwashers

1 Answer

The dishwasher has been running for 3 hours and seems to be stuck on 1 minute left. Upon opening, there was sudsy water remaining in the bottom, but the dishes looked clean. The washer just won't go to...


SHU 53 MODELS To start test program, press and hold both SCRUB WASH and DELICATE/ECONO program buttons, then turn unit on by pressing ON/OFF button. Initially, control module version # will be displayed (e.g./ ?21? = version 1 with jumper). When wash program buttons are released, lights above them will flash. To end test program, press ON/OFF button. To check each program indicator light, press its button. To check Cycle Countdown display, Refill Rinse Agent light and REGULAR WASH light, press REGULAR WASH button (press Delay Start button to test Cycle Countdown display alone). Cycle Countdown display will show ?88″ when REGULAR WASH button is pressed and ?8h? when Delay Start button is pressed. To start testing, press both the SCRUB WASH and DELICATE/ECONO buttons a second time. When testing has ended, Cycle Countdown display will show a fault using codes below. If more than one fault occurs, code numbers will be added together, (e.g./ ?6? = faults 2 + 4). 0 = No faults detected 2 = Heating fault 8 = NTC (temperature sensor) fault 1 = Aqua Sensor (?Sensotronic?) fault 4 = Filling fault F = Filling fault (display occurs during wash, not test) To check for heater, high limit or flow switch problems, start testing until heating starts. Using a meter with a current coil, measure current going into dishwasher. If current is ~ 11 A, then heater, high limit and flow switch are OK. If current stays at ~ 1.5-2 A, then heater, high limit or flow switch are faulty. If water level switch (f1) has failed (opened), display will show fault code ?4″ and unit will continually fill and drain where testing won?t be completed. If flow switch (e5) has failed (opened), display will show ?0″, water won?t heat (to 150?F) and water won?t stop circulating. If NTC probe (f2/f4) has failed (opened), display will show fault code ?8″ immediately and testing will end shortly after water has started circulating.

Aug 01, 2009 | Bosch SHU5315UC Dishwasher

1 Answer

Dishwasher during normal cycle gets hung up and does not advance


HI. this is just a control fault. you can try to reset the core program by unplugging this unit for 5 minutes. this will drain all power and reset the core on the timer/control.

If you experience the same situation after this reset, simply replace the control/timer module.

Jun 02, 2009 | Kenmore Dishwashers

1 Answer

Bosch dishwasher timer sticking


I have been told to replace the timer which I am looking to do the same to my machine!

Mar 24, 2009 | Bosch Dishwashers

1 Answer

None use for 7 days


I have a fisher paykel dd603 dishwasher. If I select the normal wash setting on the top drawer, it posts the time in the lcd screen as 56 mins. The unit will wash as usual until it reaches the 28 min mark. At this point it will stay on 28 mins and continue to run, but it won't rinse or empty the drawer of water. Also it never counts down below the 28 min mark. It has flashed a F4 and F1 code. I've cleared them both, and checked to make sure that no water is standing on the bottom of the unit, and that the heating element is working. I should mention that the top drawer did overflow about two weeks ago, and that I did clean up the water. I don't know where to look from here. Any suggestions?

Sep 10, 2007 | Fisher and Paykel 23 in. DD-603SS Built-in...

Not finding what you are looking for?
Kenmore 24 in. 15932 Built-in Dishwasher Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dishwashers Experts

Fred Sops

Level 2 Expert

271 Answers

D. E. Hev

Level 3 Expert

1059 Answers

Raisin Brann

Level 1 Expert

28 Answers

Are you a Kenmore Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...