Question about LG 4.0 Cu. Ft. 7-Cycle Front-Load Washer - White

1 Answer

Washing stops after a min or two & LE flashes up!

It is starting up fine but just stops after 2 mins, flashes LE. The clothes are very wet

Posted by on

  • Anonymous Mar 23, 2014

    clothes still wet with 2 min. left

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 76 Answers

This is caused by an error from the hall sensor on the motor. It is possible that one of the connectors has come loose (this is an issue with LG's or it could be the hall sensor it's self is bad. First check that the harness that connects to the motor is tight. If that doesn't help then the hall sensor will have to be replaced. The hall sensor is located on the motor. The hall sensor basically tells the computer which direction and what speed the drum is turning.

Posted on Nov 16, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can you tell me what nf means


No fill error. The washer thinks it's taking too long to fill up with water

Dec 14, 2014 | Kenmore Elite 45986 Front Load Washer

1 Answer

Washing machine 11 years old is jumping on the wash cycles. EG instead of taking 25 mins its taking 10 mins to complete -clothes coming out wet unless manually turn to spin again


It is possible that the program is not running to the designed settings and so the program seems to skip the cycle.
The clothes come out wet because the spin cycle is not activated in the set program. Hence the program controller needs a check.

Jan 17, 2011 | Hoover Washing Machines

1 Answer

No cycle runs longer than 20 minutes and the clothes are still dripping wet when done.


The motor could be overheating and shutting down. Does it stop mid cycle and the timer keep advancing? if so when it stops wait for it to cool down and try starting it again. If it will not start for a few min. then does it is the motor overheating.

Jun 23, 2010 | Washing Machines

2 Answers

Washer has stopped at 26 min with water in the drum. Will not spin or drain. Just sounds like it starts running then stops and repeats.


Good deal your machine is a Series 11.

“”Washer has stopped at 26 min with water in the drum. Will not spin or drain. Just sounds like it starts running then stops and repeats.””

I believe this is the start of a Spin Cycle of that Wash Cycle which Wash Cycle did you have selected?

Are there any error codes to the LED display like dC or uC?

If you stop that wash cycle with the wet load and do a Spin Only cycle will it complete with no error code?

Does the wash tub bang around in Spin Only cycle with the wet clothes load?

Standing by for some feedback and I will try to help.

Here is the Service Manual and parts look up. Can you let me know if you want to try to DIY the fix?

FAV6800A/FAV9800A Service Manual for reference. Sears Parts Direct for reference.

Rich

Apr 11, 2010 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

Cycle takes forever


IE is Inlet Error. Turn off the water valves behind the washer and remove the hoses from the machine end. Look inside the spot the hoses were attached to, and use a plier to pull out the screen and clean it out. (probably only need to do the cold side) Re-instert screen(s), re-attach hoses, and turn valves back on. (Also, make sure hoses are not kinked behind machine.) Times displayed are estimates, and vary due to water fill rates, and load type and size. In your case, the water fill rate is the problem.

Jan 25, 2010 | LG WM1814CW Front Load Washer

1 Answer

Haier washer/dryer combo not drying clothes


Check things like the Filter / clear fluff...Make sure outlet hose if any is not kinked and passing air..Hope this helps..

Oct 02, 2009 | Haier 14.3 lb. Washer/Dryer Combo

1 Answer

LE code flashing on WM1812CW


LE code is overload on motor. This unit actually has a magneto and stator. This is what needs to be replaced. Usually find a magnet cracked.

Aug 27, 2009 | LG WM-1832C Front Load Washer

2 Answers

Wash cycle stops with 1 min left and clothes are sopping wet


dl mean door lock system fail. may be lose connection on your door lock or control board.

May 23, 2009 | Washing Machines

Not finding what you are looking for?
LG 4.0 Cu. Ft. 7-Cycle Front-Load Washer - White Logo

Related Topics:

241 people viewed this question

Ask a Question

Usually answered in minutes!

Top LG Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a LG Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...