Question about Kirby Generation 3 Bagged Upright Vacuum

1 Answer

How do I change the fan in a Kirby G3 vacuum cleaner

I have a Kirby G3 and the fins on the fan are bad and must be replaced but I don't know how to do that. I have done just about everything else but not sure how trhe old fan comes off the unit.

Posted by on

  • Anonymous Dec 11, 2008

    I found out the fan doesnt like srews. It went kaplooe. How do I fix it

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Kirby Expert
  • 324 Answers

See this MANUAL. Let me know if it helped

Posted on Dec 02, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

Tip

How To Replace a Belt on a Kirby Generation G3-Sentria Vacuum Cleaner


Greetings,

Below we explain how you can replace a vacuum cleaner belt on the Kirby Generation upright vacuum cleaner. All you will need to perform this repair is a new Kirby Generation Upright Belt, and some time. No tools are needed to perform this repair. This repair is the same for all Kirby Generation models including: G3, G4, G5, G6, Ultimate G, Kirby Diamond Edition, and the Kirby Sentria. The repair procedures have to be followed exactly in order for the vacuum to work properly. This should be done at least once a year even if the belt doesn't break, because these belts will stretch out over that year time period and will not work as well as a new belt would.

I hope that you find this video helpful. If you do, please be sure to rate this Tip as helpful by clicking the Thumbs Up Icon in the top right hand corner of the Tip.

Feel free to send me an email anytime if you have any questions on the repair of the Kirby, or any vacuum cleaner.


Video Repair on how to Change a Belt on a Kirby Generation Vacuum Cleaner;



Thank you so much,

Chris Jones
GoVacuum

on Mar 19, 2010 | Kirby Ultimate G Bagged Upright Vacuum

1 Answer

Change belt on Kirby heritage vacuum


It is the same as installing a Kirby Generation belt.
Here is a walk through:
Install Kirby belt and nozzle

800-775-6586
GpodVac com

Sep 15, 2014 | Kirby Vacuum Fan Heritage G3 G4 G5 Ult G...

2 Answers

How do you attach the belt for the roller-brush on a Kirby Generation 3, up-right vacuum-cleaner?


Greetings,

Please see the attached video on how to replace the belt on a Kirby Generation Vacuum Cleaner. This is an easy to follow step by step direction on the proper way to replace the belt, as well as do basic maintenance on your Kirby's roller brush which will prolong the life of your belt greatly if done regularly. I you find this video to be helpful, please be kind and rate it well by clicking the thumbs up icon below.

Feel free to request a repair clarification if you have any quesitons on how to replace the belt on your Kirby.

How to Replace the Belt on a Kirby Generation 3 (G3) Vacuum Cleaner:



Thanks for watching!

Chris J.

Jun 14, 2009 | Kirby Generation 3 Bagged Upright Vacuum

1 Answer

Replace the roller on my kirby vacumm generation 3


http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=814340
Generic problem for all Vacuums
Replace the roller on my
Posted by tlourene on Jul 21, 2008
Replace the roller on my Kirby Vacuum Generation 3
Hello,
I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedure. In order to replace the brushroll on the Kirby G3 you need to dial off the belt and then release the lever to remove the bell housing, then there are 2 levers that you need to open then you can get @ the brushroll --- take out the brushroll and replace the brushroll and a new belt – make sure you change the belt every 4 to 6 months for the best cleaning. Make sure when you put the new belt in the housing that the screw heads are facing down – then you can replace the bottom plate, dial the belt on to the belt pulley and replace the bell housing. If you need further help please refer to a local vacuum cleaner dealer in your area. So if you need further assistance, please feel free to contact your local vacuum cleaner dealer in your area or in the yellow pages, or contact the factory phone number or website to further assist you with your questions.

http://kirby.com/
Customer Service – U. S. & Canada
1-800-494-8586
Hours 8:00 am to 5:00 pm (EST)
Mail To: Consumer Relations
The Kirby Company
1920 West 114 Street
Cleveland, OH 44102
Thanks, Don the Vac Man
Go Ahead. Use Us.

Jul 21, 2008 | Vacuums

2 Answers

Putting a new belt on on my kirby sentria


http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=780370
Generic problem for all Vacuums
Putting a new belt on
Posted by cowangelgirl on Jul 14, 2008
Putting a new belt on my Kirby Sentria
Hello,
I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedure. The belt install on a Kirby is to raise the height adjustment to the highest level and then dial the belt off counter clockwise so it is loose and not on the fan pulley, release the top lever on the bell housing, then remove the bottom plate and unhook the brushroll on one side, slide the old belt off and then slide the new one on, replace the brushroll with the screws facing the carpet and re-hook the bottom plate on the Kirby. Then take the bell housing and hook that back on to the Kirby and lock it down. Then dial the belt on clockwise all the way and the belt should be on the fan pulley. The belt should be ready to go, plug in your Kirby and then do the step down on the vacuum height adjustment until the tone changes, then try to see id it picks up, if not go one more height adjustment and that should be the correct setting.

So if you need further assistance, please feel free to contact your local vacuum cleaner dealer in your area or in the yellow pages, or contact the factory phone number or website to further assist you with your questions.
http://kirby.com/
Customer Service – U. S. & Canada
1-800-494-8586
Hours 8:00 am to 5:00 pm (EST)
Mail To: Consumer Relations
The Kirby Company
1920 West 114 Street
Cleveland, OH 44102
Thanks, Don the Vac Man
Go Ahead. Use Us.

Jul 14, 2008 | Kirby G6 Bagged Upright Vacuum

3 Answers

I have lost My Kirby G5 Manual


http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=11561&thid=539967
I have lost My Kirby G5 Manual
Posted by Marie1231 on Apr 23, 2008
Kirby G5 Bagged Upright Vacuum
I need to know how to use the attachments that came with the Kirby. I know how to use the shampoo/vacuum, but not the other attachments or the upholstery cleaner. Does anyone have any idea?

Hello,
I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedure.
1st, you need to un-hook the lever @ the top of the Kirby head, dial off the belt from the Kirby Vacuum Head using the Kirby emblem in the front of the vacuum, that also serves as a hook/spoon to dial the belt off the fan pulley. Once you have removed the vacuum head you now hook up the attachment hose to use the attachments by locking the attachment hose to the top lever. All regular Kirby attachment will fix on the attachment hose end including the spin brush if you have one with your Kirby --- using the Kirby Shampoo spray the soiled area and use the spin brush to agitate the carpet and or upholstery, try not to use to much water. If you have a Kirby shampooer – use the recovery tank on the exhaust port of the Kirby (this means that the cloth/paper bag needs to come off and install the clear recovery tank. Please refer to the Kirby owners manual for any type of trouble shooting that you might need – or please feel free to contact your local vacuum dealer in the yellow pages or contact your Kirby factory manufacturer listed below:
http://kirby.com Contact Us by Phone
United States and Canada 1-800-494-8586
Between the hours of 8:00 am to 5:00 pm EST
Monday thru Friday
Thanks, Don – The Vac Man
Go Ahead. Use Us.

Apr 23, 2008 | Kirby G5 Bagged Upright Vacuum

2 Answers

Fan kit kirby g4 vacuum cleaner


I'm assuming you mean the fan impeller and not the fan that cools the motor...

you can find detailed instructions at this site

http://reviews.ebay.com/KIRBY-VACUUM-REPAIR-HOW-TO-REPLACE-THE-FAN-IMPELLER_W0QQugidZ10000000003711302?ssPageName=BUYGD:CAT:-1:LISTINGS:3

hope this helps!

Jan 13, 2008 | Kirby G4 Bagged Upright Vacuum

2 Answers

Bad fan


Take off the bag and handle, remove casing, then you can remove the front casing to get to the fan. Turn the belt spindle to the right to unscrew it, then pull off fan and replace it with a new one. You may have to lock the armature to be able to unscrew the spindle.

Oct 26, 2007 | Kirby Ultimate G Bagged Upright Vacuum

Not finding what you are looking for?
Kirby Generation 3 Bagged Upright Vacuum Logo

Related Topics:

147 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kirby Vacuums Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18299 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Roger Potts

Level 3 Expert

694 Answers

Are you a Kirby Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...