Question about Jensen WBT210 Consumer Microphone

1 Answer

PIN Code I'm loose manual for wbt210. Please send me PIN Code

Posted by on

1 Answer

Re: PIN Code - Jensen WBT210 Consumer Microphone Microphones

The pin code is 0000

Posted on Jun 01, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

My sm58 has a low level buzz or hum. how should I proceed to diagnose and repair. I am assuming a loose wire or a frayed wire grounding out.

This could be any of several things. IF the audio output of the mic is at a normal level then the first thing to check is the mic cable. I have several things to discuss so read all of this and then test.

First, I found six BRAND NEW XLR cables were wired wrong... the vendor had 13000 of them in stock and was going to have to check them all. The cables appear to work, but had the shield and one signal wire in the wrong place so the line was NOT a twisted pair balanced as required, but instead a plain coax. I had to repair these at a venue when I discovered the problem. Please google the correct XLR configuration. The pin numbering is NOT what one would expect. You cables (open the ends and look) should have the shield tied to pin 1 which is one of the side pins. Mine they had the shield on the middle pin or apex of the triangle.

Second, there are COUNTERFEIT Shure SM58's being sold. Read about that at google... If you unscrew the screen and find a label on the side of the element, the mic is a fake... Now there are two qualities of fakes... some perform ABOUT as good as the genuine, and others don't even have the balancing transformer.

If the hum is only there while handling the mic, the ground to the shell is not connected... this is mainly a mechanical connection. You can extract the XLR male plug from the bottom of the mic by removing the side screw and gently pull out by grabbing one of the pins. Also you can verify the wire colors as the fakes use the wrong color wires.

Noise problems are my specialty so if you need further help send a comment to me.

Mar 25, 2011 | Shure SM58 Professional Microphone

1 Answer

Audio Technica PRO-35: need wiring diagram for mic end

If you feel the shield goes to the middle, try red on one terminal and white on the other. If not, reverse it.

If it's labeled on the circuit 1, pin 2, pin 3, then pin 1 is usually ground, pin 2 is hot (red), and pin 3 is cold.

Mar 31, 2010 | Audio Technica Audio-Technica AT2020...

1 Answer

Telex 56 to cobra 4 pin

Hi there!!

the yellw wire is not used on the microphone conector most of them are just cut and left in there loose as long as its not shorting out on anything!! The wiring for the telex 56 for your radio Cobra 29 LTD is as follows: PIN #1 Shield & Red, PIN #2 White, PIN #3 Blue, PIN #4 Black, Yellow wire not connected!!

If you notice when you have the connector apart on the back of the pins where the wires get soldered to the pins are numbered so you will know which pins they are or on the front side of the connector the pins are also marked wich numbers they are!! If you have any other questions please feel free to e-mail us at:

Apr 18, 2009 | Telex M-560 Consumer Microphone

3 Answers

Don't know the conections of blue or red

If we're talking about the microphone cable wiring on a low impedance mic remember this. Cheap mic cables with XLR's on both ends often have no standard color code to follow. True pin 1 is ALWAYS ground (shield wire) but the other two wires could be any color of the rainbow. Look for small numbers beside each pin of the XLR connector and make sure that pin two on one end of your cable, is also pin two on the other end as well....etc. Special note: The XLR connectors set screws have reversed threads and it's the same for the XLR male plug in the bottom of the microphone as well.....Glen

Dec 24, 2008 | Shure Beta 58A Professional Microphone

1 Answer

Holden ventura 2000 stereo code

The radio will have to be removed from the car dashboard

.Then please quote the MAKE + MODEL of your radio plus ALL the LETTERS and NUMBERS on any LABELS , BARCODES or STAMPED IN THE METAL CASING.

Also quote the MAKE of CAR it is fitted into.

Please note: Not all stereo codes can be calculated from the Serial Number

Dec 02, 2008 | Rycote Stereo Windshield (Size Code AE)...

1 Answer

One works but the other doesnt

in most samsung phones there is an option setting right key by the screen that will route the call through the phone or the other divice i think you may have to switch it in a call first though

May 08, 2008 | Jensen WBT210 Consumer Microphone

2 Answers

My wbt210 is looking for signal. The usb and computer it is plugged into have found wbt210.

right click your sound settings in the task bar and make sure its not turned down or muted

Apr 02, 2008 | Jensen WBT210 Consumer Microphone

1 Answer

External mic

No you can't !! This unit only has an audio out but the mic is built into it. You have to speak into the WBT210 when you connect to a phone call.

Mar 14, 2008 | Jensen WBT210 Consumer Microphone

Not finding what you are looking for?
Jensen WBT210 Consumer Microphone Logo

Related Topics:

183 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jensen Microphones Experts


Level 2 Expert

611 Answers

Ben Armstrong

Level 2 Expert

332 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Jensen Microphone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides