Question about PDAs

3 Answers

Z22 will not charge or go on - PDAs

Posted by on

  • johndrost Nov 16, 2008

    Radio Shack said our Palm needs new batteries and only an expert can install them????

×

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 347 Answers

Hello,

Have you tried changing the battery of your PDA?

Posted on Nov 15, 2008

  • Santiago Vallejo
    Santiago Vallejo Nov 16, 2008

    Hello,

    I foufn this step by step procedure:

    1Perform a HotSync operation to back up the latest data in your Palm handheld. 

    2Open the back battery cover and remove the existing batteries. 

    3Replace with new batteries, making certain you correctly place the batteries according to the positive (+) and negative (') signs. Do not follow the springs for battery placement! 

    4Wait a few seconds, and then turn on your Palm device. 

    5If you've lost any data, perform a HotSync operation to replace it.


    If you are not sure about what you are about to do, let me know and i will help you locate a palm store near you.


    Link to the page where they describe how to replace the battery

    Good luck,
    Dahaka

  • Santiago Vallejo
    Santiago Vallejo Nov 16, 2008

    PS. remember to rate this solution if you found itsolved your problem.


×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,712 Answers

Try this:

Connect your unit to AC adapter to begin a charge cycle, then perform a SOFT RESET, of the Z22, (rear reset button), and then leave connected to the charger to complete a charge cycle, about 4 hours.

If this does not work, the battery will need to be replaced as it is faulty. The Palm Z22 is powered by a rechargeable lithium-ion battery. The battery is 3.7 volts and delivers 950 mAH. Be sure that your battery is compatible. You don’t want to fry the Z22 with a high-powered, incompatible battery.

Posted on Nov 15, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 101 Answers

Try reseting your palm

instructions, click here

Posted on Nov 15, 2008

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a Palm z22 that won't keep a charge. My


The Palm Z22 is, I have found out, a bullet-proof design in regards to reliably keeping your valuable "DATA" safe over time. The Engineers at PALM really did a good job of Data integrity compared to many other devices. HOWEVER -- there are 3 common problems with the growing AGE of the Z22, 2 are with the dying batteries, and 1 with the years of wear and tear on the touch screen. The battery is a typical square, thin, modern Lithium battery, wired in with two wires ( + positive, red, and - negative, black ) that can be
taken out and replaced if you take the unit apart. In a brand new, in-the-box package, the battery is dying simply from old age. If the Z22 was used heavily, the constant cycling from dead to fully charged wears out the battery even more. The Touchscreen is a thin layer of plastic stretched over a sheet of glass, with a tiny air gap in between. Over time, the top plastic layer deforms - with hot and cold, air pressure changes, and being pressed by wearing the unit in a pocket, purse, briefcase, or even in a drawer with pencils, pens, and staplers etc. It is very important to have a hard cover over the screen! Other than just having the battery loose its weak charge continually, there is a problem with the unit getting into a state of BLACK SCREEN - it does not charge and remains "apparently" dead, since the logic circuits are in an invalid state, and it can only be reset if the battery dies COMPLETELY to remove the power on the logic circuits.
I have covered the topics of the battery problems, the data problems, the screen problems, and the disassembly, maintenance, and security, and how to get data off the unit, particularly to the new Windows Operating Systems that were developed AFTER the Z22 was no longer made. This is at
kidbots.com/WEBADD/Z22_PALM_PILOT/Z22_PALM_PILOT.html
I have ripped apart the Z22 repeatedly, and posted pictures of the various steps to service these units. There are links to aftermarket software to transfer data, and examples of how to USE the Z22, for valid purposes. This should be a one-stop source for any information or troublehooting the Z22, for those who have the Z22 and want to keep it operating!
good luck

robin dusty graves

Z22 PALM PILOT
palm-z22-keep-charge#solution-section-jquljdhkw5zrsfvn5uli2qb2-3-0.jpg palm-z22-keep-charge#solution-section-jquljdhkw5zrsfvn5uli2qb2-3-1.jpg palm-z22-keep-charge#solution-section-jquljdhkw5zrsfvn5uli2qb2-3-3.jpg palm-z22-keep-charge#solution-section-jquljdhkw5zrsfvn5uli2qb2-3-6.jpg palm-z22-keep-charge#solution-section-jquljdhkw5zrsfvn5uli2qb2-3-10.jpg

Mar 09, 2010 | Palm Z22 Handheld

1 Answer

Can we charge Z22 handheld through PC??


Sometimes if you plug them in to the hot sync cable they will charge. This works for my TX however I am not sure about the Z22. I am including a link to the palm free chat service. Normal 0 Scroll to the bottom of the page and you will see a Palm Chat. From there click on the link that says Chat Now and follow the online prompts. Best wishes...I hope this will help you.
They can answer that questions for you there. I have used the free chat service and it worked great for me. Best wishes.

http://kb.palm.com/wps/portal/kb/na/zire/z22/unlocked/supportservices/page_en.html

Nov 13, 2009 | Palm Z22 Handheld

2 Answers

My Palm Z22 won't turn on. If I do a hard reset


It absolutely won't, you don't have to worry. I've done it several times, and I know I was really nervous at first, but it's fine.

Nov 01, 2009 | Palm Z22 Handheld

1 Answer

My z22 Palm will not keep a charge and after a day


The battery needs to be replaced. They are sold on Ebay but if you need to do any kind of soldering then the best bet is to take it in and have it done by an authorized repair. It is worth the little extra you will pay.

Best wishes.

Oct 12, 2009 | Palm Z22 Handheld

2 Answers

How do i fix the touch screen on my palm z22?


I am repeating a previous answer, since it covers most of the common problems :
The Palm Z22 is, I have found out, a bullet-proof design in regards to reliably keeping your valuable "DATA" safe over time. The Engineers at PALM really did a good job of Data integrity compared to many other devices. HOWEVER -- there are 3 common problems with the growing AGE of the Z22, 2 are with the dying batteries, and 1 with the years of wear and tear on the touch screen. The battery is a typical square, thin, modern Lithium battery, wired in with two wires ( + positive, red, and - negative, black ) that can be
taken out and replaced if you take the unit apart. In a brand new, in-the-box package, the battery is dying simply from old age. If the Z22 was used heavily, the constant cycling from dead to fully charged wears out the battery even more. The Touchscreen is a thin layer of plastic stretched over a sheet of glass, with a tiny air gap in between. Over time, the top plastic layer deforms - with hot and cold, air pressure changes, and being pressed by wearing the unit in a pocket, purse, briefcase, or even in a drawer with pencils, pens, and staplers etc. It is very important to have a hard cover over the screen! Other than just having the battery loose its weak charge continually, there is a problem with the unit getting into a state of BLACK SCREEN - it does not charge and remains "apparently" dead, since the logic circuits are in an invalid state, and it can only be reset if the battery dies COMPLETELY to remove the power on the logic circuits.
I have covered the topics of the battery problems, the data problems, the screen problems, and the disassembly, maintenance, and security, and how to get data off the unit, particularly to the new Windows Operating Systems that were developed AFTER the Z22 was no longer made. This is at
kidbots.com/WEBADD/Z22_PALM_PILOT/Z22_PALM_PILOT.html
I have ripped apart the Z22 repeatedly, and posted pictures of the various steps to service these units. There are links to aftermarket software to transfer data, and examples of how to USE the Z22, for valid purposes. This should be a one-stop source for any information or troublehooting the Z22, for those who have the Z22 and want to keep it operating!
good luck

robin dusty graves
Z22 PALM PILOT
Z22 PALM PILOT fix-touch-screen-palm-z22-ngl0e1lc0ft3j10pmz4xzklk-4-0.jpg fix-touch-screen-palm-z22-ngl0e1lc0ft3j10pmz4xzklk-4-1.jpg fix-touch-screen-palm-z22-ngl0e1lc0ft3j10pmz4xzklk-4-3.jpg fix-touch-screen-palm-z22-ngl0e1lc0ft3j10pmz4xzklk-4-6.jpg

Aug 17, 2009 | Palm Z22 Handheld

2 Answers

Screen goes blank and requires a soft reset with "memo"


I believe that this problem relates to the BlackScreenOFDeath or BSoD - which is caused by a low or weak battery allowing the CONTROL Logic circuits to get into an invalid state where the ON/OFF/SLEEP/CHARGE/ FUNCTION transistors are niether on nor off. I would recommend getting a new battery as soon as possible. Doing a SOFT RESET "may" get you temporarily going again. DO NOT do a HARD RESET !. I have posted many discussions on the Z22 that you may find helpful, on my tiny website,
http://kidbots.com/WEBADD/Z22_PALM_PILOT/Z22_PALM_PILOT.html
One other possibility, is to take apart the Z22, and wipe the buttons and traces with a soft damp cloth to remove oils, water, and possible spilt liquids from the touch/snap/button/discs areas. Even the tiniest trace of conductive liquids will short out the logic circuits, causing "unknown: states on the control circuits.
My answer on the BLack ScreenofDeath, is as follows:
__________________________________________________
The Z22 suffers from 3 problems. One of these is the Black Screen of *****. I got a used Z22, and over the years discovered this problem. The small battery was a perfect fit of power and size when manufactured, decades ago, but, time alone has deteriorated the capacity, so that a "NEW" , sealed-in-the-box Z22 today, has a weak, dying battery that needs replacing. These are $10 free shipping from China. The BSoD seems to be caused by a dip in power from the battery to the LOGIC CIRCUITS that control the ON/OFF/SLEEP/CHARGE, etc states of the Z22. If the logic gets out of sync, the unit is in an INVALID state, will not charge, nor respond to the LOGIC buttons on the front - these buttons are NOT the standard ON/OFF buttons from the past that mechanically connected or diss-connected power. All the buttons on the Z22 are touch snap disks that are connected to transistors, to flip logic states. THUS, is the power in any of the transistors gets low, the transistor is neither ON nor OFF, and the control circuits are in a messed-up state. Or another way of looking at it, the ON button is a logic gate on a transistor network, and the only way to activate the "ON" logic state, is with full power to the circuits! -- the power on the Z22 is ALWAYS ON. . . The screen may turn off, and the chips may go into "sleep" mode, but the Z22 is always on. SO if there as a weak battery, you may get the random Black Screen of *****. The GOOD news, is the the DATA and programs that you purchased are incredibly SAFE, as long as you do NOT do the HARD RESET (which someone suggested ! (NOT ) ). I have ripped apart the Z22 dozens of times, and subjected it to freezing and heating and all sorts of horrible things, the data has always been 100% reliable, -- stored in permanent memory. There is a quick way to get rid of the BSoD - you have to open the unit and cut one of the two battery wires, wait 2 minutes to kill the logic circuit power, then re-connect. I added a switch on the Z22, just for this purpose. I would recommend, if you get the Z22 re-powered, to get a new battery as soon as possible. This should clear the BSoD for a while. See my tiny website :
http://kidbots.com/WEBADD/Z22_PALM_PILOT/Z22_PALM_PILOT.htm
There are many photographs and step by step procedures to try to get the data off the device, maintain the Z22, get parts, and use the Z22 with the new 64 Bit Windows computers. The BEST way to use the Z22 would be to get an old Widows 32 bit laptop (ie WinXP), and simply connect the Z22 in a standard way using the software that it was designed for... The new patches to 64 bit machines, are very limited, and many previous features do not work.
So the bottom line - all your data, information, and programs are safe. You simply have to reset the LOGIC CIRCUITS (this has nothing to do with the PALM Z22 SOFT and HARD Resets !) - it has to do with disconnecting the power from the battery, or waiting until the battery is COMPLETELY DEAD ! (which can take a long time! )...
Good luck
robindustygraves sept 2014 ( robin dusty graves )
Z22 PALM PILOT

Z22 PALM PILOT b24a4c23-cde3-44eb-a542-221e23771cfb.jpg 5d677a3f-163a-4546-ae79-d98c6fb397b6.jpg 5cb49c67-a9f7-4dbc-90df-4cf481cf4e2d.jpg badc8899-3493-408c-b9aa-fa81dc391d93.jpg ab336a44-9ab4-44a2-97f6-d3720b8639c9.jpg

Jan 30, 2009 | Palm Z22 Handheld

2 Answers

Absolutely black screen - will not power up - did not give warning of low battery - palm z22 about 2 years old ---is it dead????


The Z22 suffers from 3 problems. One of these is the Black Screen of Death. I got a used Z22, and over the years discovered this problem. The small battery was a perfect fit of power and size when manufactured, decades ago, but, time alone has deteriorated the capacity, so that a "NEW" , sealed-in-the-box Z22 today, has a weak, dying battery that needs replacing. These are $10 free shipping from China. The BSoD seems to be caused by a dip in power from the battery to the LOGIC CIRCUITS that control the ON/OFF/SLEEP/CHARGE, etc states of the Z22. If the logic gets out of sync, the unit is in an INVALID state, will not charge, nor respond to the LOGIC buttons on the front - these buttons are NOT the standard ON/OFF buttons from the past that mechanically connected or diss-connected power. All the buttons on the Z22 are touch snap disks that are connected to transistors, to flip logic states. THUS, is the power in any of the transistors gets low, the transistor is neither ON nor OFF, and the control circuits are in a messed-up state. Or another way of looking at it, the ON button is a logic gate on a transistor network, and the only way to activate the "ON" logic state, is with full power to the circuits! -- the power on the Z22 is ALWAYS ON. . . The screen may turn off, and the chips may go into "sleep" mode, but the Z22 is always on. SO if there as a weak battery, you may get the random Black Screen of Death. The GOOD news, is the the DATA and programs that you purchased are incredibly SAFE, as long as you do NOT do the HARD RESET (which someone suggested ! (NOT ) ). I have ripped apart the Z22 dozens of times, and subjected it to freezing and heating and all sorts of horrible things, the data has always been 100% reliable, -- stored in permanent memory. There is a quick way to get rid of the BSoD - you have to open the unit and cut one of the two battery wires, wait 2 minutes to kill the logic circuit power, then re-connect. I added a switch on the Z22, just for this purpose. I would recommend, if you get the Z22 re-powered, to get a new battery as soon as possible. This should clear the BSoD for a while. See my tiny website :

http://kidbots.com/WEBADD/Z22_PALM_PILOT/Z22_PALM_PILOT.htm

There are many photographs and step by step procedures to try to get the data off the device, maintain the Z22, get parts, and use the Z22 with the new 64 Bit Windows computers. The BEST way to use the Z22 would be to get an old Widows 32 bit laptop (ie WinXP), and simply connect the Z22 in a standard way using the software that it was designed for... The new patches to 64 bit machines, are very limited, and many previous features do not work.

So the bottom line - all your data, information, and programs are safe. You simply have to reset the LOGIC CIRCUITS (this has nothing to do with the PALM Z22 SOFT and HARD Resets !) - it has to do with disconnecting the power from the battery, or waiting until the battery is COMPLETELY DEAD ! (which can take a long time! )...

Good luck

robindustygraves sept 2014

Z22 PALM PILOT 691d763d-1b45-4323-a389-5dd3900ad65d.jpg 4ab4c25b-c05c-4deb-898e-d858abbab87f.jpg b63d6d62-a28c-4450-b1de-0e692a79ae08.jpg 8387fdcf-76fa-42ab-a7d4-e941d697b879.jpg

Nov 11, 2008 | PDAs

1 Answer

I just bought a palm Z22 PDA. I used the AC charger to charge the Z22 but when I attempted to attach the USB synch cable I noticed that the plug is different from the plug on the AC charger. The USB...


I have concluded that the USB synch cable is not the correct one for my Palm Z22 PDA. There is only one point of attachment on the PDA and it is different from the plug on the USB synch chord. This was the last Palm Z22 PDA in the store so I think that the store clerk rounded up leftover parts and components of previous PDA kits and tried to make a complete set out of it. I am going to return the PDA to the store (Staples) in the next day or two.
Thanks for your offer of help. I will contact you again in the future if I need help.

Oct 15, 2008 | Palm Z22 Handheld

4 Answers

Palm Z22 will not turn on


I had this problem in the very beginning and a few times after. What worked is the following.
Put it to charge for at least half an hour. You won't see it is charging or anything.
Then, while connected to the charger, press the reset button.
Have you guys tried it like this already?

Feb 02, 2008 | Palm Z22 Handheld

Not finding what you are looking for?
PDAs Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top PDAs Experts

k24674

Level 3 Expert

7987 Answers

kakima

Level 3 Expert

96683 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a PDA Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...