Question about HP Color LaserJet 2600n Printer

1 Answer

We keep getting a page with a picture of a train

Hi!

The printer wasn't working yesterday unless we pushed the green button twice. Today, I keep getting a sheet with a picture of a train instead of the 8.5 x 11 inch that I requested to have printed. (YIKES - it is using up all my colour!!!!)

Please help

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 32 Answers

I belive that picture might be a demo page.
Try this:

  1. Go to the menu in the printer display that reads "Service". Press select, or the check mark key.
  2. Use the arrows and go to the option called "Restore Defaults". Press Select.

This will bring your printer back to factory defaults and reset the printer. However this will reset any special settings you set up and if you printer has an internal I/O card for a network connection this will also be reset.

If this printer is conneted directly into a pc then you should be able to perform the reset with minimal risk.

Posted on Nov 19, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have refilled my color ink. After it prints 20 pages it lights up the "color ink" button meaning it's out of ink and starts printing poorly. I tried refilling twice with new ink - same thing happened.


Try this, it will reset your counter.

Power off printer
Hold down STOP/RESET button then Press and Hold down Power button
Keep Power button down and Release STOP/RESET button
Push STOP/RESET button twice
Wait 20-30 seconds - our LED showed Idle
Push STOP/RESET button four times
Push Power button twice
Power off
Next time the printer is started the waste count will have been reset

Sep 12, 2010 | Canon PIXMA MP210 Photo All-In-One Printer

1 Answer

Waste ink reservois is full


Hi
The waste ink are in the inside of your printer you need to get at it to clean out, but after this you got to reset it after you cleaned it or it will still not work, you may not have to get inside to clean it try this first to reset it.
Reset CANON PIXMA IP5000 printer To reset the counter or to find out about it’s reading you have to use the service mode.
Turn off the printer, push the resume button and keep on pushing.
Press the power button and keep on pushing. Now let go off the resume button,
but not the power button. Push the resume button twice, then let go off all buttons.
You are now in service mode.

To leave the service mode, give the power button one push.

Push the resume buttons once, after that the power button once.
The first information page appears.
Push resume twice, then power once: You get the second page.

Newer PIXMA-printers print the first page as a test for the nozzles.
The second page contains a lot of information.

Our advice: Print the second page before and after reset of the waste ink counter.
Only then can you be sure that the reset was a success.

To reset the waste ink counter right now, push resume four times and after that power once.

Important: Before starting with normal printing again, switch off the printer.
That gets you out of service mode.

Then switch on the printer again and print, as you like


Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

Feb 02, 2010 | Canon PIXMA iP5000 InkJet Photo Printer

1 Answer

CODE 5100 ON PIXMAMP450


MP450 Hi there
You can try to reset the cartages this may do it Please call back let us know if it worked for you, PLEASE.


Power off printer
Hold down STOP/RESET button then Press and Hold down Power button
Keep Power button down and Release STOP/RESET button
Release power button
Push STOP/RESET button twice
Wait 20-30 seconds - our LED showed Idle
Push STOP/RESET button four times
Push Power button twice
Power off
Next time the printer is started the waste count will have been reset.

Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

Jan 29, 2010 | Canon Pixma MP450 All-In-One InkJet...

1 Answer

My canon Pixma IP1500 start blinking 10 times alternationg orange and green, then repeats. I even reset waste ink counter, but no luck. Please help me out. Thanks.


How To Reset Waste Ink Canon Pixma MP450

Hi there
You can try to reset the cartages this may do it Please call back let us know if it worked for you, PLEASE.


Power off printer
Hold down STOP/RESET button then Press and Hold down Power button
Keep Power button down and Release STOP/RESET button
Release power button
Push STOP/RESET button twice
Wait 20-30 seconds - our LED showed Idle
Push STOP/RESET button four times
Push Power button twice
Power off
Next time the printer is started the waste count will have been reset.

Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

Jan 29, 2010 | Canon PIXMA iP1500 InkJet Photo Printer

1 Answer

Absorber reset code for pixima ip5000


Hello there here is the codes.
The waste ink are in the inside of your printer you need to get at it to clean out, but after this you got to reset it after you cleaned it or it will still not work, you may not have to get inside to clean it try this first to reset it.
Reset CANON PIXMA IP5000 printer To reset the counter or to find out about it’s reading you have to use the service mode.
Turn off the printer, push the resume button and keep on pushing.
Press the power button and keep on pushing. Now let go off the resume button,
but not the power button. Push the resume button twice, then let go off all buttons.
You are now in service mode.

To leave the service mode, give the power button one push.

Push the resume buttons once, after that the power button once.
The first information page appears.
Push resume twice, then power once: You get the second page.

Newer PIXMA-printers print the first page as a test for the nozzles.
The second page contains a lot of information.

Our advice: Print the second page before and after reset of the waste ink counter.
Only then can you be sure that the reset was a success.

To reset the waste ink counter right now, push resume four times and after that power once.

Important: Before starting with normal printing again, switch off the printer.
That gets you out of service mode.

Then switch on the printer again and print, as you like


Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

Jan 19, 2010 | Canon PIXMA iP5000 InkJet Photo Printer

1 Answer

Paper comes out blank


Ok here is the code you need.
The waste ink are in the inside of your printer you need to get at it to clean out, but after this you got to reset it after you cleaned it or it will still not work, you may not have to get inside to clean it try this first to reset it.
Reset CANON PIXMA IP5000 printer To reset the counter or to find out about it’s reading you have to use the service mode.
Turn off the printer, push the resume button and keep on pushing.
Press the power button and keep on pushing. Now let go off the resume button,
but not the power button. Push the resume button twice, then let go off all buttons.
You are now in service mode.

To leave the service mode, give the power button one push.

Push the resume buttons once, after that the power button once.
The first information page appears.
Push resume twice, then power once: You get the second page.

Newer PIXMA-printers print the first page as a test for the nozzles.
The second page contains a lot of information.

Our advice: Print the second page before and after reset of the waste ink counter.
Only then can you be sure that the reset was a success.

To reset the waste ink counter right now, push resume four times and after that power once.

Important: Before starting with normal printing again, switch off the printer.
That gets you out of service mode.

Then switch on the printer again and print, as you like


Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

Jan 08, 2010 | Canon PIXMA iP5000 InkJet Photo Printer

1 Answer

Will not power back up.


Hi
The waste ink are in the inside of your printer you need to get at it to clean out, but after this you got to reset it after you cleaned it or it will still not work, you may not have to get inside to clean it try this first to reset it.
Reset CANON PIXMA IP5000 printer To reset the counter or to find out about it’s reading you have to use the service mode.
Turn off the printer, push the resume button and keep on pushing.
Press the power button and keep on pushing. Now let go off the resume button,
but not the power button. Push the resume button twice, then let go off all buttons.
You are now in service mode.

To leave the service mode, give the power button one push.

Push the resume buttons once, after that the power button once.
The first information page appears.
Push resume twice, then power once: You get the second page.

Newer PIXMA-printers print the first page as a test for the nozzles.
The second page contains a lot of information.

Our advice: Print the second page before and after reset of the waste ink counter.
Only then can you be sure that the reset was a success.

To reset the waste ink counter right now, push resume four times and after that power once.

Important: Before starting with normal printing again, switch off the printer.
That gets you out of service mode.

Then switch on the printer again and print, as you like


Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

Jan 05, 2010 | Canon PIXMA iP5000 InkJet Photo Printer

1 Answer

Where can I buy the waste ink absorber pads for both printers?


Hi
The waste ink are in the inside of your printer you need to get at it to clean out, but after this you got to reset it after you cleaned it or it will still not work, you may not have to get inside to clean it try this first to reset it.
Reset CANON PIXMA IP5000 printer To reset the counter or to find out about it’s reading you have to use the service mode.
Turn off the printer, push the resume button and keep on pushing.
Press the power button and keep on pushing. Now let go off the resume button,
but not the power button. Push the resume button twice, then let go off all buttons.
You are now in service mode.

To leave the service mode, give the power button one push.

Push the resume buttons once, after that the power button once.
The first information page appears.
Push resume twice, then power once: You get the second page.

Newer PIXMA-printers print the first page as a test for the nozzles.
The second page contains a lot of information.

Our advice: Print the second page before and after reset of the waste ink counter.
Only then can you be sure that the reset was a success.

To reset the waste ink counter right now, push resume four times and after that power once.

Important: Before starting with normal printing again, switch off the printer.
That gets you out of service mode.

Then switch on the printer again and print, as you like


Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

May 23, 2009 | Canon PIXMA iP5000 InkJet Photo Printer

1 Answer

Printing problem


Turn off printer
Hold down green button
Power on printer. (cold reset)
In printer properties choose print directly to printer, then choose print test page.

Weird problem

Feb 06, 2009 | HP LaserJet 1320 Printer

1 Answer

Error number 1700 canon s9000 printer


knowing printer manufacturers I doubt they even have a sensor to detect that its full at all, they probably based on something crumby like print count. here are some instructions to reset the waste ink tank, the instructions vary so try them until one does the job :
Waste Ink Tank Reset

1: Power off printer
2: Hold Resume button then press and hold POWER, the beeper will sound once.
3: Hold POWER and release RESUME
4: Press RESUME twice, then release all buttons
5: When the indicator lights steady, press RESUME three or four times. The indicator should be orange.
6: Press Power to set data



1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not, press the Power button once more.
8. Your printer should respond as normal.



1. power off Printer
2. Push and hold resume button and push power button
3. Hold Power button and release Resume button
4. Push Resume button twice ( 2x ), and now release resume button and power button
5. Green light will blinking and stop.
6. When green light on, push resume button 4 x
7. Push Power button and printer will off, if that isn't off, push power butto again until print off position.

Aug 20, 2008 | Printers & Copiers

Not finding what you are looking for?
HP Color LaserJet 2600n Printer Logo

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Printers & Copiers Experts

kakima

Level 3 Expert

96396 Answers

k24674

Level 3 Expert

7987 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you a HP Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...