Question about JVC RX-317 Receiver

3 Answers

No sound form speakers I have the same problem has ANYONE posted a solution?

Posted by on

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,806 Answers

Could you please give us more details i.e. make and model

Posted on Nov 15, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,913 Answers

Press power button for 10 second then it reset also put away battery, then refix it again.

Posted on Nov 15, 2008

  • kishor khatri
    kishor khatri Nov 20, 2008

    chehcyour speker cionnection to reciver it maybe faulty.

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • JVC Master
  • 19,396 Answers

That can be a cable problem , faulty speakers, or an internal fault, give us more details on the problem.

Posted on Nov 15, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No surround sound


firstly Jessica you will need either a cd or some form of media that is recorded in surround sound then make sure all wiring is in it's right sockets then while your "cd" is playing configure the amplifier. I hope this will be of some help goodluck.

Nov 26, 2013 | Yamaha RX-V373 5.1 AV Home Theater...

1 Answer

Very dull sound from the 4 rear spekers on my 7.1 set up for the ONKYO 802. This happens for the satellite input for tv channels, is this normal that I will only get surround sound via a disc or other...


Your basic setup through the Onkyo establishes the base levels of each speaker channel with test tones. The tones should also sound pretty much the same from speaker to speaker.

How a given surround mode works with a given input would be documented in the manual. Even stereo sources can be proecessed into some form of 7-speaker output.

"ONKYO 802" is not unique. Are there letters?

Jul 20, 2011 | Audio & Video Receivers

1 Answer

I have had the Kenwood VR-407 since 2001. I also have a Mitsubishi projection TV, attached to the receiver. When watching regular cable TV (u-verse), I can not get sound from the rear speakers. I am using...


Most TV stations you watch don't send a surround sound mix so you won't get anything in the back speakers. DVDs generally all have a surround mix which is why it sends to all speakers. What you are experiencing is normal, Bob.

Jan 04, 2011 | Kenwood VR-407 Receiver

1 Answer

System turns on but only hear feedback fomr speakser no sound


do the headphones work?that means the pre amp is working.
the speaker protection is maybe activated from shorted wires on the back,there should be a click 5 to 7 seconds after turning it on.
that is the relay that connects the speakers.check the speaker a and b switch. people are not aware of this,but alot of amplifiers ADD the a and b speakers,to prevent too low an impedance from parallel wiring.unless there is 4 speakers,no sound.

May 22, 2009 | Pioneer VSX-D409

1 Answer

Only Direct sound works good, and only two speakers


Some sound fields have reverberant effects that need adjusting so the levels become audible, such as in "stadium" mode. While playing one of these sound fields, navigate through the speaker setup menu and make adjustments to the "effects" percentage, and levels. Be aware however, that only in 4 channel stereo mode will your surround speakers produce sound 100% of the time. Also, in any form of Dolby Pro Logic mode you will hear more sound from the surround speakers originating from stereo source material than from monoaural material...example, a television station broadcast in stereo versus mono.

Mar 31, 2009 | Sony STR-DG710 Receiver

1 Answer

Front speakers no sound!


Most likely you have pressed the speaker AB switch, try pressing it again and see if it works.

Mar 11, 2009 | Yamaha RX-V663 Receiver

1 Answer

No sound form speakers


i've put 8 speakers on my amplifier, and it dint produce any sound, after that no more sound came out, in any single speakers, can you help me on that? do have any solutions?

Mar 12, 2008 | Audio & Video Receivers

2 Answers

Center speaker


mine is doing the same thing, you can hear a click sound and the channel will die. I think it is a relay or a shunt that trips when something goes wrong with that amp. I dont think it is worth repairing as there are some nice receivers out there for cheap. Maybe just a cold solder joint somewhere? Anyone know where and Ill dive in and resolder and post the results.

Feb 24, 2008 | Sony STR-DE545 Receiver

1 Answer

Pioneer VSX-4900S Receiver Connections


I know this is an old post but run front speaker outputs to the inputs on the sub then from the sub to the front speakers. bam!! it should work

Jan 23, 2008 | Audio & Video Receivers

Not finding what you are looking for?
Audio & Video Receivers Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top JVC Audio & Video Receivers Experts

 Elex
Elex

Level 2 Expert

49 Answers

Cindy Wells

Level 3 Expert

4755 Answers

Rod
Rod

Level 2 Expert

224 Answers

Are you a JVC Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...