Question about Kenwood KDC-715S

1 Answer

Faceplate is stuck on protect

I was listening to music and all of a sudden my kenwood faceplate read protect..i can not seem to get it to start working again. I do not know anything about this product, I bought the car with the system already inside it. I need help either reseting it or seeing if I need to take it in to get fixed.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 199 Answers

Hi sounds like you have a speaker issue,
try disconnecting the speakers and reconnecting them one at a time.

either that or the power output stage is faulty

Mark

Posted on Nov 17, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What cause the display to go out on the kenwood kdc-235 cd player


Hi there,

You could try reading my tip on repairing Kenwood faceplates.

How to repair Kenwood Faceplate


Cheers,

Jan 02, 2013 | Kenwood KDC-MP235 CD Player

1 Answer

Have a kenwood car stereo, MP3. It has been stuck on on screen that displays protect and will not play anything.


You should disconnect the red wire that goes to battery. Leave disconnected for at least 8 hours so the player can reset. Most newer electroinics have these stupid protection systems that are way to touchy. I think companies just don't want us listening to loud music anymore.

Sep 03, 2009 | Kenwood KDC-MP228 CD Player

1 Answer

I have a Kenwood kdc-mp2035 and it says protect on the screen and plays no music. how do i get rid of that so i can listen to my music again????


You can try pressing the reset button, worked for me for months but now, for me, the "PROTECT" never goes away... But the reset button worked for months, give it a try!

Sep 02, 2009 | Kenwood KDC-MP2035 CD Player

1 Answer

Kenwood KDC-MP235 CD player flashes Protect


check for shorts in your speaker wiring..

Mar 25, 2009 | Kenwood KDC-MP235 CD Player

1 Answer

Need to reset the code for a kenwood kdc-mpv7019


If You Have The Remote Here Is Your Solution.

1) Turn on the car.
2) The faceplate rotates out and the CODE - - - - prompt appears.
3) Press >>| and Auto keys simultaneously on the faceplate and hold for 4 seconds. (If the faceplate rotates back into the console push on the upper left top edge of the faceplate and it will flip back around. Press the Eject button and then try it again.)
4) The screen will still say CODE, but the - - - - will disappear! When this happens press the 5 key on the remote twice and it enters a K on the display on the faceplate. Hit the >>| key on the faceplate.
5) Press the 2 key on the remote three times and it enters a C on the display on the faceplate. Hit the >>| key on the faceplate.
6) Press the 2 key on the remote once and it enters an A on the display on the faceplate. Hit the >>| key on the faceplate.
7) Press the 7 key on the remote twice and it enters an R on the display on the faceplate. Hit the >>| key on the faceplate.
8) The radio goes into All Off mode and you are set! Hit the SRC button on the faceplate to select CD, Radio, etc

Thank You For Using Fixya.com Please Don't Forget To Rate My Answer

Jan 08, 2009 | Kenwood KDC-MPV7019 CD Player

1 Answer

Replacing the facepale


that hole on that model is for a locking screw, the locking screw is installed to minimize theft and for other precautions. If the face plate is having any odd reactions its normally do to the flex cable. The best sign for a dying or dead flex cable is at the joint. The joint can be viewed at the point when you remove the face plate. Immediately after pulling the face plate off look behind the pivoting frame at the orange colored ribbon, you should only be able to see a small portion of it. If there is any sign of a yellowy residue its a sign that the protective covering of the ribbon is deteriorating. A bad flex cable is everything on the moving face plates.

Sep 06, 2008 | Kenwood KDC-716S CD Player

6 Answers

Kenwood KDC-MP2035 security code


yo tengo un reproductor kenwood kdc-mp2035cr pero este no me reproduce nada solo me sale un mensaje que dice protect y no me deja hacer nada ni colocarle nada por el auxiliar

Jun 05, 2008 | Kenwood KDC-MP2035 CD Player

2 Answers

Kenwood car CD player not working


This means that some one has entered the wrong security code more than 3 times. time to take it to a dealer

Mar 19, 2008 | Kenwood KDC-MP5032 - Car Audio CD MP3...

2 Answers

KENWOOD RADIO


take a pen and press the reset button ...it's a tiny little button next to the button that takes off the faceplate...

Jan 18, 2008 | Kenwood KDC-MP235 CD Player

3 Answers

'Protect'


What is the make and model and year of your vehicle, and is it the radio that came in the vehicle from the factory?

Nov 27, 2007 | Kenwood DPX302 CD Player

Not finding what you are looking for?
Kenwood KDC-715S Logo

Related Topics:

105 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood Car Audio Receivers Experts

xxxxxx xxx

Level 3 Expert

4706 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Pablo Gonzalez

Level 3 Expert

733 Answers

Are you a Kenwood Car Audio Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...