Question about Technics SL-1210 Turntable

3 Answers

Technics SL-J1 turntable drive belt

I have a Technics SL-J1 turntable and the drive belt has perished can anyone tel me the size / part number or where I can get a new one.

Regards
Cliff

Posted by on

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 132 Answers

Hello Cliff,
You will need 2 belts, if the turntable belt is gone the other is not far behind . One for the turntable size 23.6 inch by .188 and one for the tracking motor that is in the top cover part, is a 3.0 inch by .046 belt. best place to get them is at kenselectronics.com part numbers 1407-201 and AV-SBS3.0 if you have been checking around you will see other sizes, I have a SL-J1 and have used these and they work perfectly.
Tony

Posted on Nov 13, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

This is available from the most trusted belt seller on eBay. If you do not want a PayPal account, you can buy an eBay Gift Card at a grocery store and use it :0)

http://www.ebay.com/itm/271038160519

Posted on Jul 24, 2013

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

Where are you located?

Posted on Nov 17, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What size belt on the SL-Bd22


Just purchased a belt for my SL-BD22 from Vintage Audo (Audio?). The belt size is 23.6 X .180 X .025 inches. Their part number for this belt is:B00926DJ74. Hope this helps.

Oct 21, 2012 | Technics SL-BD22 Turntable

1 Answer

I had not used my turntable for about five years due to no needle. Found a needle and played two LPs, then on the third one, it just did not move or work at all. It lit up but just acted like it had no...


The low grinding noise could be the motor spinning with "no load" i.e the belt has snapped or fallen off due to being perished.
Lift the platter to refit the belt and or replace it if required.

Jul 23, 2010 | Technics SL-BD22 Turntable

2 Answers

I HAVE A TECHNICS TURNTABLE SL-QD35 THAT IS DIRECT DRIVE AUTOMATIC THAT IS SPINNING TO FAST.


i got my turntables repaired by these guys www.technmics1210repair.co.uk
i did they made my setup work like new so im going to spread the word.
give them a shot

Apr 03, 2010 | Technics SL-1200MK2 Turntable

1 Answer

Which belt fits a Technics SL-J1 turntable? Thanks for help


I have some listed as item number 330354991790 on Ebay ... softwaredivision

Feb 05, 2010 | Turntables

1 Answer

Where can I purchase a new rubber belt to drive my Servo Automatic turntable SL-B210 Ths is not an electronic belt


Here is a link for Technics Turntable replacement belts...just scroll way down the page for your SL-B210 belt listing $10.00. Hopes this helps.
http://www.turntablebasics.com/belts/technics.html

Oct 28, 2009 | Technics SL-1210 Turntable

1 Answer

Belt?


Wow, I didn't think anyone still had one. Now that I think about it, I may still have one somewhere myself. :)

The belt you need is a FM 24.5

You can order one for $10.00 at http://www.turntablebasics.com/belts/technics.html


Jul 18, 2009 | Technics SL-1210 Turntable

1 Answer

How do you install the belt in a Technics LP SL-B300


assuming that you have the correct size belt, remove the platter and place the belt onto the platter (bottom side). Replace the platter and using a pencil, grab the belt and place it around the motor hub. The slot in the platter should give you enough room to do this. Dan

Jun 07, 2009 | Technics Turntables

1 Answer

How do I change belt on a Technics linear SL -H350 turntable


http://www.archive.org/details/Turntable_Belt_Installation

above video should help. if your platter is "stuck" then call them for tips. also make sure it does NOT say "direct drive" on the front of the unit.

presuming you are talking about the SL-H350 as in the body not the SL-DZ1200 as in the title

Jan 03, 2009 | Panasonic Technics SL-DZ1200 Turntable

2 Answers

All my vinyl sounds warped on turntable


Most common problem is the belt getting soft, especially if it has sat for a long time. It will get a weak spot where it sat on the drive pulley and every time the turntable goes around and hits that weak spot it will slow down a little making it sound like a warped album.

The belts are usually very easy to replace. Usually just lift off the turntable or there might be a small clip on the center pin, then it lifts off. Replacement belts can be ordered from several places, as shown in this search... http://www.google.com/search?&q=SL-B200+Technics+turntable+belt

Feb 17, 2008 | Technics SL-1210 Turntable

1 Answer

Technic turntable SL-101


http://1200s.com/Store/PARTS-TECHNICS-TURNTABLES/c271_272_278/index.html

These guys are pros.

Nov 07, 2007 | Technics SL-1210 Turntable

Not finding what you are looking for?
Technics SL-1210 Turntable Logo

Related Topics:

1,358 people viewed this question

Ask a Question

Usually answered in minutes!

Top Technics Turntables Experts

 Grubhead
Grubhead

Level 3 Expert

4593 Answers

T-Comtech Repairs
T-Comtech Repairs

Level 2 Expert

411 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

5653 Answers

Are you a Technics Turntable Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...