I have had the tv about 6 yrs all good , been in the same spot in the lounge room so wife need to change room around , unpluged tv moved it to new spot , plug it in pressed on button nothing is happening stand by red light is blinking & when i go to back of tv & put my ear to it i can hear a ticking sound
My tv is about 6 yrs old and its a prjection tv, when I turn the tv on it cuts on and off 3 times then will not do anything for abot 2 mins then when I turn it on again it does the same thing as before. The picture will not come on unless u do this constantly for 2 hrs strait!!! I can can hear it clicking to come on but it doesnt make it sometimes.
An expert who has achieved level 3 by getting 1000 points
An expert that got 20 achievements.
An expert that got 10 achievements.
An expert that got 5 achievements.
Re: not turning on
You need to replace the flyback which is flyback 259296 and also capacitor CP150 and CP114. You can get replacement parts at the following link and they include free step by step instructions with pictures so you can easially repair the set yourself. Heres the link. http://servicemanuals.vstore.ca/
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
You can try adjusting the Red color output. (Very touchy adjustment)
you take off the front cover/speaker cover, there should be a access panel. Behind
that, there should be a small square black box with 6 screws on it.
This is the focus block. (At least this is where most of them are
It sounds more like you may need less red in the mix. There is a screw for each color. R, G, and B. Do not
mess with the focus screws, just the ones labeled 'SCREEN.'
Go to an unused input where the screen should be dark. Barely turn the red down in a dark room so that the red spot is at the same level as the Blue and Green.
Use an insulated screwdriver and DO NOT TOUCH the focus block and ESPECIALLY NOT the back of it. Very HIGH VOLTAGE. I found that out the hard way.
Do not turn any of these up too high or damage may occur and the TV may detect a short and shut off.
have found that if the three colors are adjusted in a dark room to
where the 3 color spots (R/G/B) are just barely visible on the screen
at equal levels, there is a pretty good color balance.
First try to unplug it from the wall outlet, wait 5-10 min and plug it back in. If same problem continues - next step is to replace the lamp. Any DLP projection TV needs at least 2"-3" "breathing" space around sides, top and back of the set for proper airflow. But most likely case - lamp died because of too much hours of use in previous location. Lamp designed to work around 4500-5000 hrs. in realistic environment. Looks like having it on display, store used most of those hrs up. Sorry for bad news. Good luck! Russ.
Resetting the TV NOTE: Some TVs have a reset button. If available and accessible, try using the reset buttons before using the steps below. Using the reset buttons can save time. 1.Unplug the TV power cord from the power outlet. 2.Unplug any connected devices (DVD, Set-top boxes, etc...) 3.Press and hold the TV power button for five seconds. 4.Plug the TV power cord back into the power outlet and turn on the TV. 5.Open the on-screen menu to confirm that the TV is responding again. 6.Turn off the TV and reconnect the devices. 7.Turn on the TV.
it could be as simple as the tv feeding back on itself in a dark room. it is adjusting the light level because of what it sees ambient in the room. turn on a light near the tv and see if it stays constant now.