Question about Tribest Green Power CS1000 - CitriStar Juicer

1 Answer

Spring clip for spout

We lost the little spring clip that holds the spout up. where can i get a new one?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that has over 10 points.


    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers
Re: spring clip for spout - Tribest Green Power CS1000 - CitriStar Juicer Juicers

888.254.7336 or

Posted on Feb 19, 2015

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Spare part needed

contact the manufacturer thru their website .

Jan 17, 2016 | Juicers

2 Answers

Hi, how do I get started with a bifinett juicer kh 450 please, a friend gave me one. Thanx

Safety advice
1. Before using your citrus press for the first time, please read thro
and this safety advice carefully.
2. The citrus press is to be connected only to an earthed mains soc
installed in accordance with the applicable regulations.
To avoid accidents, never operate several household appliances f
at the same time.
3. This citrus press is intended only for domestic use.
4. Do not use this citrus press outside.
5. Do not leave the citrus press to operate unattended or allow chi
6. Handle the moving parts of the device with extreme care and ca
7. Do not remove the mains plug by pulling on the mains cable. Gra
8. Do not allow the mains cable to hang down.
9. Do not immerse the device in water or hold it under running wat
to the section "Cleaning".
10.Keep this safety advice for later reference and if necessary pass
11.Should the mains cable become damaged, it must be replaced b
centre or electrical equipment repair centre. To prevent dangerou
all repairs of electrical equipment must be carried out by suitably
 Press cone
 Juice filter/sieve
 Sieve holder / juice container
 Housing with cord storage (on underside)

ne"> Before first use
• Before using your citrus press for the first time check that the local mains electricity supply
corresponds with that indicated on the citrus press.
• Before using the citrus press for the first time clean the press cone, juice filter, juice container
and spout. Please refer to the section "Cleaning".
1. Insert the plug into the mains socket.
2. Wind up any excess cable on to the underside of the citrus press and fix the cable in the
recess at the back of the underside of the base.
3. Place the device down on a flat sturdy surface. Always keep the citrus press out of reach
of children.

Using the citrus press
Note: Before juicing we recommend that you roll the fruit on the work surface whilst pressing
down gently. In this way you will obtain-more juice. We also recommend that you clean the
citrus press immediately after use. Please refer to the section on "Cleaning".
1. Open the lid.
2. Place the sieve holder / juice container in the device.
3. Select the appropriate juice press. The small press piece is intended for fruit with little flesh.
The larger press is placed on the smaller so that juice and flesh can be obtained (ideal for
pressing larger fruit such as grapefruit etc.).
4. Place the sieve with the small press (or both presses) on to the motor spindle. The citrus
press tongue and the juice collector handle must be in line with one another.
5. Insert the plug into the mains socket.
6. Place a glass under the spout.
7. To open the spout press it downwards.
8. Press a fruit half on to the press - the device starts automatically and stops when the fruit
is removed. The alternating left-right movement of the press obtains the best yield of juice.
9. Push up the spout before you remove the glass from beneath it. This ensures that the spout
does not continue to drip.
10.When the citrus press is not needed any longer, pull out the plug and remove any fruit residue
from the sieve.
1. Before cleaning always remove the plug from the mains socket.
2. Remove the press cone, juice filter and juice container from the device.
3. Press the spout fully downwards and clean it thoroughly.
Note: The spout cannot be removed from the device.
4. Clean the press cone, juice filter and juice container under running water.
Note: These parts can be washed in a dishwasher. Place the parts in the upper basket
of the dishwasher.
5. Clean the citrus press housing with a moist cloth only. To remove stubborn dirt put a little
detergent on the cloth. Never use harsh cleaning or scouring agents.
Never immerse the motor housing in water or wash it under running water.

Nov 18, 2014 | Juicers

1 Answer

My juicer leaks under the spout. I can not figure out why. I have checked all the assembly and all the directions. It is only the second time I have used this. My machine is brand new. Any though

The spout, itself is hinged. It has two positions, an upper and a lower position. (Similar to a light switch). Make sure it is in it's lowest position when making juice, otherwise the liquid will collect in the inner bowl and leak out the sides of the juicer. Move the spout to the upper position to temporarily stop the flow of juice, such as when you change glasses or receptacles. Then, put the spout in the lower position to resume the flow of juice.

Dec 26, 2012 | Jack Lalanne Power Juicer 250 Watts

1 Answer


Try this site for the juicer part you need ..

Please vote !!

May 12, 2010 | Jack Lalanne Power Juicer 250 Watts

1 Answer

How to clean the Jack LaLane Juicer?

the blade can be removed possibly with your hands, if you can manage to turn it, if not then find something that will fit into those little holes of the blade to turn it, and then take it apart, but remember in what order. to put it together: the grey thing with the spout attached goes on first, then the orange basket, then the blade, but don't turn it too tight, just look for the indicator marks and line them up with the arrows, then the black lid, and then the pulp basket.make sure that the black lid in the back, goes INTO the pulp collector, it is not very far, but if it is not done like this, then your machine will not work. then you raise and lock the bar into place and put the pusher into the feeding tube. hope that helps.

Jun 21, 2009 | Jack Lalanne Power Juicer 250 Watts

1 Answer

How do I remove the filer cone for cleaning?

I suggest pick it up by spout & other side of bowl & shake a little & it should release from the base unit

Jan 06, 2009 | Breville Juicers

1 Answer

Jack la lanne juicer

Heres where you can buy a new one:

Aug 05, 2008 | Jack Lalanne Power Juicer (Stainless...

1 Answer

Juice lady

On the stainless steel basket notice a notch cut out on the rim above the spout and an indentation on the back of the basket near the rim. The plastic ring must snap on to the steel basket before placing the assembly on the motor housing. If it does not snap on, it is not fully seated. After the ring is seated and on the motor base, push the basket on and spin it. Confirm that the basket clears the ring. Place the top cover with feed tube over the unit and lock the two clips down. This procedure should solve your problem.

May 13, 2008 | Juicelady JL500 Juice Extractor

1 Answer

Screw that holds down the blade in cwnter

try here, not sure if it's listed or not though:

Sep 02, 2007 | Acme 5001 Supreme Juicerator Juice...

Not finding what you are looking for?
Tribest Green Power CS1000 - CitriStar Juicer Logo

Related Topics:

185 people viewed this question

Ask a Question

Usually answered in minutes!

Top Tribest Juicers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers


Level 3 Expert

479 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you a Tribest Juicer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides