An expert who has achieved level 3 by getting 1000 points
An expert that got 10 achievements.
An expert that got 5 achievements.
An expert that has over 10,000 points.
Re: own kameleon remote control, need codes for goodmans...
Hopefully if you could post back with the exact model of the Kameleon (All for One, 8 in 1, C6, Touch Zone and others) as well the brand and model of the unit you would want it to interact with, we can try narrowing the choices further.
For the time being, you may want to reference this page, here or here.
Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information. Good luck and kind regards. Thank you for using FixYa.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
You have this backwards. The codes are stored in the remote. If your Mitsubishi remote is programmable, you can search for a code that will control your Magnavox combo. If no code is found, you may have to get another programmable remote and search again.
The All for One Remote has a "Magic" button, instead of entering a code press the magic button and then press stand by, if the box does not turn on/off, then repeat the process (magic button and stand by) until it does. when it eventually goes off, store the code(i think you press ok).
in setup for guide plus U must enter the time and date along with UR correct post code and select freeview as UR input then the correct input route of UR freeview box ie EXT2 then proceed as instructed. also you must select program number 102 on you freeview stations for the eye to send signal to UR box .the eye for the guide plus must be placed directly in front of the freeview box by it`s remote control reciever.
To convert this player to Multi-Region
1. Open the disc tray.
2. Place a region 1 disc in the tray, but don't close it.
3. Press the buttons 0, 1, 2 and then 3 on your remote control in order, one at a time.
4. Press the play button on either your remote or the player.
To return this player back to Region 2 only and its factory default settings
1. Open the disc tray.
2. Press the Zoom button on your remote control.
3. Press the Retu To return this player to Region 2 only (alternative method) rn button on your remote control.
4. Your player should now go into Standby mode.
5. Press the Power button on your remote control.
i). Open the disc tray
ii). Place a region 2 disc in the tray, but don't close it
iii). Press the buttons Return and then Play on your remote control in order, one at a time
Connectivity problem. Without knowing your models and their available channels etc., it's very difficult to advise you exactly.
Broadly though ...... you need to get the input signal routing sorted.
Plug your aerial into the Freeview box. Make a connection from its RF out, (beside the aerial 'in' socket) to the aerial 'in' socket on the JVC. Run yet another co-axial connection from the JVC RF 'out' to the television.
Now - connect a scart lead between the JVC and the TV. Power off the freeview. Switch your TV to accept A/V - to show the JVC on screen. Read/go through the 'Set up' procedure on the JVC to scan in the available broadcast channels. When done - connect using a scart between the Freeview box and the JVC. This will be located on either the L1 or L2 channel selection.
IF as it seems you are using the freeview to watch all your programmes - and record in then you are simply watching and recording 'live' change the Freeview programme and the JVC gets that same one arriving in (and sending to the TV)
Unless you need to record Freeview only output - always record from the aerial input. You select via the television remote (and 'TV' selected) and the appropriate channel.
Complex to explain - hope it helps. The one thing to remember - is to make one set of changes at a time - check the result is okay, before moving to the next.
I had the same problem. The answer is to use a scart lead on the freeview box and connect it to the input/output scart on the DVD. Then connect a scart lead from the TV out on the DVD to the TV.
You then press Video source on the DVD remote until 'scart' is displayed to pick the freeview channels.
Hope that helps