Question about Zenith C27A24T 27" TV

1 Answer

Cant turn down volume

Also cant get remote to work

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 252 Answers

Some of the button was stock up,it needs to replace all of the botton

Posted on Nov 14, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why cant I get my volume buttons to work on my all in one remote for tv


Check the setup manual, you need to re-assign the function of the volume buttons to the selected function.

Jun 17, 2016 | Standard (CRT) Televisions

1 Answer

I cant find my remote, and my TV's volume buttons seem to be stuck. I need to be able to turn the volume up and down, but they wont do anything. Do any other remotes work with this TV, or am I out of luck?


HMMMM....you have a bad capacitor in the deflection area of your TV. This bad cap will raise the high voltage to a level unaccustomed to the power supply. Eventually this TV will shut down. You will need a tech to find the capacitor or two and replace them. This will lower the voltage to a proper and working level. The remote or universal one, will not operate your TV properly at this time. A common problem for your Curtis Mathis. Thanks for asking and show a few hands of support.

Jan 27, 2011 | Curtis-Mathis CM27101S TV

1 Answer

The volume on my tv goes down all by itself. I turn it up and it goes right back down to 0. With remote or manually, does the same thing. Also, can't turn tv off. have to unplug it to turn it off. Any...


Try taking the batteries out of the remote or taking it out of range from the tv. Then try turning the volume up on the Tv manually. If the volume continues to go down on its own then it is a problem with the tv set itself. If the problem stops with the remote out of the picture then it is a remote problem. As far as powering the unit off may be a similar issue. If there is an on/off button on the tv and it works to turn the power on but not off then it is a tv issue. If the remote turns the tv on but not off it may be something as simple as the wrong code being programmed into the remote(universal remote) or if it is the factory remote it may be an issue with that. You could try getting a new universal remote that works with your unit.

Jul 09, 2010 | Toshiba 32A33 32" TV

2 Answers

Cant get Sky+ Remote to work volume on Bush LCD32TV16HD


Hi,
I rang Bush help line and got more set-up codes and that worked,we can now work the volume off the sky remote.

Oct 24, 2009 | Standard (CRT) Televisions

3 Answers

When i turn the tv. on, the volume line appears all the way to zero. if i turn the volume up, it goes up but when i release the up button the volume goes down all by itself.


It sounds like one of the volume down buttons is stuck in the activate position. The same as if you were holding the down volume button continuously. It could be either the volume down button on the TV or the remote. I would try remove the batteries of the remote then adjust the volume by the TV buttons.


If the volume doesn't go back down then the remote is the problem. In order to fix the remote you may need to take it apart. This is normally easy to do just locate any screws that may be holding the remote together. If you don't see any screws then you will need to pry the two sections apart. Separate the circuit board and rubber buttons and clean them both with some rubbing alcohol and reassemble it. If it still has the volume issue you may need to replace it.

If the problem persists with the remote deactivated then it's the volume button located on the TV. That is a little more difficult. You can try wiggling the button or some canned air (used to clean computer keyboards) to blow it clean. However it may need to be disassembled to gain access to the switches for proper cleaning.
Hope this helps.

Oct 19, 2009 | Toshiba 32A33 32" TV

1 Answer

Remote will not change the volume


Is the front funtion button works in the TV the it could be a bad remote controller(the button switch inside) :)

Apr 14, 2009 | Hitachi 43FDX01B TV

2 Answers

Zenith h25w35dt cant unlock auto program


USE ZENITH REMOTE HOLD DOWN MENU BUTTON UNTIL THE OSD DISSAPEARS THEN HIT 9876 ENTER CHANGE P/L SETTING IN FACT. MENU

Apr 08, 2009 | Standard (CRT) Televisions

2 Answers

Volume decreases by itself


maybe defective speaker or audio output ic or shorted capacitor within audio circuit

Nov 09, 2008 | RCA F32648 32" TV

4 Answers

Rca 20F420T


if you can bring up the menu try using the volume up / down and channel up/down on the remote to change your selection. that might work

Sep 01, 2007 | RCA 20F420T 20" TV

Not finding what you are looking for?
Zenith C27A24T 27" TV Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zenith Standard (CRT) Televisions Experts

The Knight
The Knight

Level 3 Expert

68301 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

Anastasio Benjou

Level 2 Expert

99 Answers

Are you a Zenith Standard (CRT) Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...