Question about RCA Projection Televisions

1 Answer

The remote control will not change chanles - RCA Projection Televisions

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 45 Answers

Try changing the batteries of the remote.

Posted on Nov 13, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I fix the remote control sensor?


Can Comcast change the remote for free? Also check the batteries on the remote.

Oct 26, 2014 | Hitachi 51S500 51" Rear Projection...

1 Answer

I do not have factory remote for my sony KDF-50WE655. how can i change it from antenna to cable?


Sony RM Y915 Remote Control ELECTRONIC ADVENTURE

Sony OEM RM Y915 TV VCR DVD Cable Remote Control TESTED

There are several web sites that carry this replacement remote. My suggestion is to purchase a remote. Then you have all the functions at your finger tips. To do a web search for the remote; "remote control for sony KDF-50WE655"

May 17, 2014 | Projection Televisions

2 Answers

62HM15 Toshiba DLP TV won't respond to remote or control panel


Blinking is a trouble code. Try unpluging for a longer time then hold power button in when pluging back in to try and reset.

Mar 15, 2010 | Toshiba 62HM15 62" Television

2 Answers

I've changed the batteries in my Philips Universal Remote and I still cannot get it to change. What should I do?


heres a handy little trick to determine whether your remote control is working. Get hold of a radio and switch it to AM band receive (any frequency). Hold the remote control near to the aerial and press any of the buttons..you should hear a squeeling noise from the radio.This proves that the remote control is working and that the TV is at fault. If you dont hear any noise from the radio, your remote control is faulty and you can obtain a new remote from the link below.

http://www.espares.co.uk/search/remote-controls/philips/p/1090/128?utm_source=google&utm_medium=cpc&utm_term=philips%2Bremotes&utm_campaign=Remote%2BControls

If you hear squeeling from the radio during the remote control test, then the TV infra red receiver board is faulty, and is located behind the small clear glass lense on the front bottom front casing of the TV. Hope this helped :)

Feb 22, 2010 | Projection Televisions

1 Answer

The TV only received High Def chanles. When switched to reg. chanels, there are green vertical lines and you can see the goast chanel behind the green lines. On pic in a pic setting the pic. chanel is...


Exact same thing happened to me last night. The TV only received High Def chanles. When switched to reg. chanels, there are green vertical lines. Light is definitely on and visible in the back. Now goes out after abut 30 sec. Misery loves company. Will watch the site for a solution. 4yrs. old just went off extended warranty 45 days ago. damn

Feb 12, 2010 | Samsung HLR5067WX 50" Rear Projection HDTV

2 Answers

When powered up-TV continually changes channels---RCA P52937SG MFG 2003


look at the control board circuit -are there and signs of heat damage if so replace board

May 02, 2009 | RCA P52937 52" Rear Projection Television

1 Answer

Remote control that no longer works, ie. no response from the TV despite changing the batteries


You can get an IR remote tester at radio chack or frys. It's just a card that you point and shoot at with the remote. If you do not see red flashing on the card replace the remote . If you do then call serv shop. remote reciever is bad.

Apr 24, 2009 | Projection Televisions

1 Answer

When I adjust the volume on the remote control it changes the channel, but not on every occasion.


Hey,
This could be due to the accumulation of dust inside the remote control. You can try to open up the controller and just clean it up.
Thanks

Apr 15, 2009 | Projection Televisions

1 Answer

My remote control for my Zenith Television Model Z27X229 will adjust the volume, but it will not change the channel. I have changed batteries, but that didn't help. Do I need a new remote control? If...


The simplest solution would be to buy a new remote for testing purposes. I own a One-for-All universal remote (model URC-4220), which I bought at Walmart, for less than 10 dollars. It is compatible with Zenith TVs. (You can return it later, if necessary).
If the channel-changing problem is not resolved with your new remote, then you will know for sure there is a defect in your TV, which requires the expertise of a repairman.

Jul 09, 2008 | Projection Televisions

Not finding what you are looking for?
Projection Televisions Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top RCA Projection Televisions Experts

The Wyzzyrd

Level 2 Expert

83 Answers

D. E. Hev

Level 3 Expert

1059 Answers

Ron Dufek
Ron Dufek

Level 3 Expert

398 Answers

Are you a RCA Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...