Question about Kenmore 63942 Dryer

1 Answer

No heat Sears Kenmore Elite Dryer Model number 110.63932102. How do you get it apart to troubleshoot? Any Pictures? It appears the element is easy to get to from the front? Thank you in advance for your help! Brian

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Sears Kenmore electric dryer model #110.96320100 will not get hot.

Posted on Nov 17, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kenmore heavy duty plus dryer modle number 886573130 works fine just stopped heating up.


Gas dryer no heat means the heating element broke or fell apart, need to install new one, go to sears hardware and order a repacement....model # in hand.

Feb 22, 2015 | Kenmore Dryers

1 Answer

Kenmore elite 110.629442100 parts diagram


model number doesn't come up but you can go here,put in your model number and see parts,sears.com
http://www.searspartsdirect.com/partsdirect/part-model/110.629442100

Nov 09, 2013 | Kenmore Elite He5T Dryer Heating Element...

1 Answer

Dryer putting out hot air but clothes not drying


You have some blockage between lint trap and where the unit vents outside.

Dec 16, 2012 | Kenmore Dryer Sears Elite

1 Answer

Kenmore 100.85081400 no heat


check the thermal fuse on the blower housing if its open some units wont heat,also check the heating element if heated electrically,or the ignitor on gas fired units,by the number you provided i believe you meant its a 110.85081400 instead of the 100.85081400 (and is electrically heated) you provided which is produced by whirlpool for sears (kenmore) also there is a control board located inside behind the control panel that may be a culprit,but check the first two things i suggested at the top

Jul 23, 2012 | Kenmore Elite HE4 Electric Dryer

1 Answer

The dryer is running but not heating up


Good Morning, It sounds like your heating element has quit. This will probably involve an element, thermostat and thermal fuse. The dryer will have to be taken apart to work on. UNPLUG MACHINE. I need the full model number inside the door on the frame, then I can help you more specifically. Have a good day.

Jan 30, 2011 | Kenmore Elite HE4 Electric Dryer

1 Answer

My kenmore elite elecctric dryer is running but I get no heat


The most likely cause, is a burned out heating element. Sears has the replacement pparts. You will need the model and serial numbers. The replacement is relatively easy. Disconnect the power and then from the back, take out the screws that hold the element housing in place. Depending on the model, you will also have to pop the top to get the unit out.

May 13, 2010 | Kenmore Dryers

1 Answer

Heating element for kenmore dryer won't turn on


Hi, I have an 11yr old 80 series elec. dryer and just fixed the same problem. On the heater element is a thermostat with 2 wires and above that about 14" is another piece with 2 wires. I had to replace the top one. They sell them together in a kit called Thermal cut off kit. Sears sell it for 25.49 look up part number 279816 or 3399848 again these numbers are for my dryer but you can look them up on the sears parts web site. If you have a sears service center near by they let me buy the parts to see which one it was and then return the ones I didn't need. I hope this helps.Good luck

Jan 05, 2009 | Kenmore Elite HE4 Electric Dryer

1 Answer

Dryer heating element


usually if it heats up but long dry times ,,air flow problem inspect exhaust hose and vent s should resolve problems...

Dec 27, 2008 | Kenmore 62602 Electric Dryer

1 Answer

I have A kenmore Elite Model #110.65942400 Ser MR2103237.


before you take it apart make sure you have not lost 1 phase of the 220 volt line into dryer , dryers will run and appear fine on 110 volts be will not heat check fuse or breaker and re-set breaker even if it does not appear tripped , if fuse in line turn off power and remove fuses and check with an ohm meter , then if you have a volt meter check for 220 volts @ socket of dryer , then we will talk dis-assembly

Dec 01, 2008 | Kenmore 659 Electric Dryer

5 Answers

Need manuals


What problem are you having, the problems i have seen with kenmore elites are below.


1. when you press start and release dryer shuts off

for this problem, change the board in the console

2. not producing heat

for this problem, check to see if 220 is getting to element, check to see if you are getting 220 from outlet, check your thermal cutoff on heating housing, check your heater relay which is located in top console.

Apr 02, 2008 | Kenmore 63942 Dryer

Not finding what you are looking for?
Kenmore 63942 Dryer Logo

Related Topics:

392 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dryers Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Tim Whalen

Level 3 Expert

3056 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Are you a Kenmore Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...