Question about ATN Aries 390 Paladin Weapon Sight

1 Answer

Aries 390 Paladin

While I was hunting suddenly at steady with infrared light for night-time type: Aries 390 Paladin, no longer functioned. I changed the batteries and everything I can to look through it, in other words, no more lights than ghidae adjustment of the target

Posted by on

  • Anonymous Dec 09, 2008

    Thanks for the tip, I tried what you said to yourself, and clean the battery gets up and measure voltage HV. Can you help me more, he might like to infrared to be burned?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

Tubes can go without warning, but power supplies usually do. Get someone to check if PSU takes a current at switch on and then measure the HV.

Posted on Nov 29, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I bought 2 outdoor CCTV.camera RV537B with night vision. one of the unit has not functioning properly on night. i tested it by covering the photo cell that switch the LED lamp which is ok but it seems to...


I think I answer you question--when?? Take the good CCTV camera and hook it up to monitor. Then hook up the CCTV camera and turn it on. Point the working CCTV camera at the bad camera that is turn on. Now, look at the monitor which is working with your operational camera. Look at the bad camera while it on, and see how many IR LED's you can see on the bad CCTV, while it turn on. You should be able to the IR LED glowing red. If not, then there is a problem with bad CCTV IR LED's. Short wire, no power to the IR LED's. stewbison

Jun 24, 2011 | Night Vision & Thermal Optics

1 Answer

There is not picture its just vioce


Battery OK, IR light up, no green image on the intensifier image tube, correct! What type of voices are you hearing? Give ATN Aries 390 two Zolof and wait two day, just kidding!!! The noise is a crackling, high freqencey hum, popping, etc. Also remove the eye lens, it screw off, then remove the scope to someplace where it semi dark. Turn it on and observe the 18mm white plate and see if it turn green---no green---no look see---no image intensifier tube, it dead that is the mage tube. stewbison.

Mar 15, 2011 | ATN Aries 390 Paladin Weapon Sight

1 Answer

When is best time to sight in ATN 390?


At night. You can sight in the 390 during the day in simi-darkness with a day light lens cover over the front of the scope. (the snap cover has a small hole in the center for look see during the day) 50 foot room with a target, bench rest and a rifle vise. You'll also need laser bore sight Figure you rifle ammunition ballistic and how many yards before it starts to drop. Set the 390 reticle to the red do on the target one or two inch above. Dead center set up will give you about two hundred yards on center... approx. Now you know this is a static test or sight in. During night because of some distortion and noise from the scope. stewbison

Feb 17, 2011 | ATN Aries 390 Paladin Weapon Sight

1 Answer

The power light comes on but I have no image.


Hello - nice looking scope and with 100 % rave reviews.
Not much to adjust really - cover off , battery inserted , turn on - adjust brightness. IR illuminator on'off.
I've just read through page 5 on user manual - at least they have a 2 yr warrantee and some phone numbers to get support.
Here is user manual / guide + trouble shooting tips. http://www.nightvisiongear.com/documents/Aries390PaladinNightVisionRifleScope.pdf
A simple test is looking at a distant street light - just incase the 'amplifier' is very sensitive. (that causes BLACK spots) .
If the amp is damaged , they would have a test -- Ray

Jan 23, 2011 | ATN Aries 390 Paladin Weapon Sight

1 Answer

HAVE ARIES MK 238 BUT CAN'T SEE THREW IT,IT HAS A NEW BATTERY.


Sorry to tell you. The image intenifier tube when south with Russian timing. I have picture of the image tube but i can't figure out how to load them here. What are you going to do with the MK338. GB....stewbison

Jan 19, 2011 | ATN American Technologies Network Aries...

1 Answer

Nite Vision scope


Unscrew front lens front of intensifier tube should have an even bronze tinted coating on glass if it is grey and blotchy the tube is degassed. common fault with this model nightvision
wayn

May 12, 2008 | ATN Aries 390 Paladin Weapon Sight

2 Answers

Nothing but Pitch black


I Have two Mk 6500 they are both pitch black inside. YES i put new battery in same thing. Is there a way I can fix this my self, they want $800.00 to fix one at ATN... these are not junk scopes..

Feb 26, 2008 | ATN Aries 390 Paladin Weapon Sight

2 Answers

Amt aries mk238 model#500433


I have a Amt aries 208 I have changed the battery but i cant get to do any thing . and i have lost all of the manuals can you help.Ed.

Nov 13, 2007 | AMT Datasouth Aries MK238 Weapon Sight

1 Answer

Problem with my atn 390 nv scope


Observe the IR illuminator with a digital camera and see if it if fluctuating in output brightness. If that is OK, the problem may be in the HV circuit. They are both easy to fix if the person has some experience.

Oct 30, 2007 | ATN Aries 390 Paladin Weapon Sight

1 Answer

Nv sight dead


No more lights steady type: Aries 390 Paladin, light guide only focus.

Mar 27, 2007 | ATN Aries 390 Paladin Weapon Sight

Not finding what you are looking for?
ATN Aries 390 Paladin Weapon Sight Logo

Related Topics:

424 people viewed this question

Ask a Question

Usually answered in minutes!

Top ATN Night Vision & Thermal Optics Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

yadayada
yadayada

Level 3 Expert

60769 Answers

wadingriver
wadingriver

Level 3 Expert

2042 Answers

Are you an ATN Night Vision and Thermal Optic Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...