Question about Seiko Smart Label Printer 100 Thermal

1 Answer

ERROR MESSAGE when it finishes coping all the files and i think its finished it show me error message 16

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Remove rests of older installations from registry:
search for "seiko" and remove everything you will find.
reboot + run setup

Posted on Dec 18, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What happened when my Kyocera Mita KM5035 Copier is unable to copy after refilling the toner?


there are many reasons for this .first make sure you installed the toner container very well. second type 1087 twice to service menue then type 30 to chick motors then exit and type 130 to adjust toner mode when the machine stop turne it off-on

Nov 19, 2015 | Kyocera Mita KM-5035 Printer

1 Answer

What happened when my KM5035 Copier is unable to copy after refilling the toner?


Konica Minolta toner cartridge you DO NOT Refill!!! You buy new ones 3rd party or OEM recommend OEM, there are electronic chips on the cartridge that tell the copier if the cartridge is new or old putting a old cartridge in with new toner is still a old cartridge to the copier!!

Nov 17, 2015 | Printers & Copiers

4 Answers

How to change settings to tell Sharp MX2300 that it no longer has a finisher/stapler unit.


Does it show the finisher onscreen? or are we just talking about when printing to it.

once you unplug the wire harness for the finished and power cycle the machine using the main power switch it should no longer display a finisher on the screen.

You need to change the configuration of the print drivers on your computer to remove finishing options when printing. right click on the copier in your devices and printers and go to printer properties. Go to the configuration tab, and click the button for auto configure. some little fingers will pop up and tell you what to select click ok and then apply.

Let me know if you are still having problems

Jan 28, 2015 | Sharp MX-2300N Color Copier

1 Answer

How do I clear error message that says to close the finisher output guide?


The finisher output guide is usually a small plastic piece about as long as the paper feed that can be opened to see the rollers, make sure that is put back down before you print.

Aug 27, 2014 | Canon iR 2016i Black and White Copier

1 Answer

Remove paper from finisher tray


If the paper is removed then check the sensor if you do not see it then have a tech come out, might need to be replaced.

Jan 23, 2014 | Konica Minolta Printers & Copiers

1 Answer

Kyocera fs-2020d doesnt do multiple copies of documents


This message often shows up when the memory is full from one document (normally a large file) to fix it you have to add external memory

Apr 16, 2010 | Kyocera Printers & Copiers

1 Answer

Sharp AR-5127, the error code U2-40


U2-40 is a board error, F1-15 is finisher lift motor error.

To reset: #, interrupt, clear, interrupt. (screen should say service mode), enter 16, print, are you sure? , yes.

For the finisher error, follow above procudure, entering 14 instead of 16. if error returns, disconnect the finisher

Nov 26, 2008 | Printers & Copiers

1 Answer

Canon iR8500 with Error E000583-0001


Hello Jeremy,
This error code has to do with your finisher. The auxillary tray is not finding its home position or does not leave the home position within the alotted time. Check for binds. I have limited exposure to the K4/3 finisher but try this. Turn the copier off, and open one of the finisher doors. Now turn the copier back on with the finisher door open so it cannot initialize. Once the copier is basically ready except the finisher door is open, close the finisher door and observe all the **** (and theres alot) initialize. This may help determine the problem. I hope this helps...........................SPINAL

Mar 12, 2008 | Canon imageRUNNER 8500 Copier

1 Answer

Hp lj 8000 error code 16-0015


Disconnect the finisher if it works we know
thats the problem.some times it is not connected to the printer
properly.

Dec 12, 2007 | HP LaserJet 8000 Printer

Not finding what you are looking for?
Seiko Smart Label Printer 100 Thermal Logo

Related Topics:

236 people viewed this question

Ask a Question

Usually answered in minutes!

Top Seiko Printers & Copiers Experts

yadayada
yadayada

Level 3 Expert

61292 Answers

NIK
NIK

Level 2 Expert

206 Answers

Tralornik

Level 1 Expert

11 Answers

Are you a Seiko Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...