Question about Dacor PCS130 Preference Electric Single Oven

Open Question

Dacor oven beeps randomly

It sarted with random beeps in middle of night. I turned the electricity off so I could sleep. Then it would beep either once or sometimes repeatedly, totally randomly, regardless of whether the oven is on or off. This has been going on for about 2 months. Recently, after repeated beeps, the display would show OFF, and the oven would then turn off. I'd have to turn off the breaker to re-set the panel!!!!

Posted by on

6 Suggested Answers

  • 159 Answers

SOURCE: Dacor Oven Won;t Heat

power surges can short out the electonics in appliances. If you can locate where the tech sheet is and I would say its behind the control panel on top, look at the wiring diagram and see if there are any replaceable fuse's. Or a resetable fuse for the heating element. If not check to see if power is getting to the main control bord. If there is power there you may need to replace the control.

Posted on Jul 20, 2007

  • 213 Answers

SOURCE: Dacor CPO130W F4 fault

f-4 on decor ovens mean the oven temp sensor is bad. replace the oven temp sensor and it will be fine

Posted on Nov 27, 2007

vitg55
  • 70 Answers

SOURCE: dacor single oven flashes an F2 error code and won't stop beeping!!!

This is from manufacture service manual:

-F2- Alarm Heating Mode High Temperature
Is activated when the ERC senses a runaway heat condition or when the temperature exceeds
“runaway limits”. The ERC will beep until the cancel or another function is selected. If the alarm
repeats the F2 alarm check the oven sensor and wiring after fi rst checking for a stuck relay. If alarm
goes away verify the oven will complete a clean cycle without any type of failure.
Another words the problem with oven sensor or relay board.

Posted on Dec 18, 2008

localwonder
  • 6784 Answers

SOURCE: Dacor error codes

HI. the F-1 code is a System Watchdog Circuit failure code.

Press "Cancel", if beeping continues after 30 seconds, replace the main control board (also called clock or ERC).

Concerning the F-5 code. This is an oven temp sensor failure code. have it replaced asap. ((Check the wiring leading to and from the control and sensor for cracks and fouled structure. if the wiring is bad, replace the harness as well)),

Posted on Aug 01, 2009

TheMobilian
  • 8147 Answers

SOURCE: Dacor oven beeps and shows F1 code

-F1- Alarm “System Watchdog Circuit”
The system will detect a failure in the internal watchdog element relay circuits and will activate a
cancel feature. F1 will be displayed in the time digits and will beep until the cancel button or another
function is selected. An F1 failure could be detected in cook or time of day mode. With an F1 failure
the ERC is picking up a command to supply heat without receiving an input from the membrane. The
watch dog circuit is designed to prevent this.
If the beep continues after pressing cancel check the main control (ERC)
Dacor

Posted on Aug 20, 2009

TheMobilian
  • 8147 Answers

SOURCE: oven beeping

yOU NEED TO CHECK THE FAULT CODE F1 MOST LIKELY THIS IS A STUCK BUTTON . HERE IS THE DACOR MANUAL

Posted on Aug 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Dacor oven keeps beeping and flashing PRB. How do I stop the beeping?


Most unwanted beeping on Dacor products are due to a bad touchpad... Use your model # and start looking for a replacement , by touchpad I mean a part something like this one: Dacor Touchpad 62678B

Jul 12, 2016 | Dacor Epicure 30" Double Wall Oven,...

1 Answer

I can't use my oven it keeps turning off and my oven is beeping and the problem light is flashing how can I fix this so I can use my oven


Kenmore electric oven keeps shutting off.... ' Sears PartsDirect

www.searspartsdirect.com > Ask an Expert
Oct 15, 2010 - Kenmore electric oven keeps shutting off. ... Can't locate your model number? Use ... hi, i purchased and replaced my etc (#316455420) for kenmore electric range model # 790.9011.2010. i was ... How to use the site (3:58) ...

Frigidaire oven Bake functions randomly beep and shut off ...


Dec 25, 2015 | Ovens

1 Answer

Our oven started randomly beeping last night with an error message of what looks like "F1" and when we push a button it stops for only 5 minutes then starts up again. Any suggestions on how to get it to...


Hi. This Usually means that either the touch pad or the oven control (also called clock or ERC) is defective and needs to be replaced. If this fault code cannot be canceled, replace the oven control (also called clock or ERC), touch pad, or both.

Dec 08, 2009 | GE Ovens

1 Answer

The screen says F0 and it keep beeping. whats wrong?


One or more push buttons are stuck. Push all buttons at random several times each. Sometimes this will release the stuck button. If that does not work you will have to replace the keypad.

Oct 12, 2009 | Dacor Ovens

1 Answer

F1 message flashing, annoying beep in the middle of the night


you could have a bad touch pad or ECU which is the main control board.

Sep 16, 2009 | Amana AOCS3040 Electric Single Oven

1 Answer

Dacor oven beeps and shows F1 code


-F1- Alarm “System Watchdog Circuit”
The system will detect a failure in the internal watchdog element relay circuits and will activate a
cancel feature. F1 will be displayed in the time digits and will beep until the cancel button or another
function is selected. An F1 failure could be detected in cook or time of day mode. With an F1 failure
the ERC is picking up a command to supply heat without receiving an input from the membrane. The
watch dog circuit is designed to prevent this.
If the beep continues after pressing cancel check the main control (ERC)
Dacor

Aug 20, 2009 | Dacor ECS130 Epicure Electric Single Oven

1 Answer

Dacor single oven flashes an F2 error code and won't stop beeping!!!


This is from manufacture service manual:

-F2- Alarm Heating Mode High Temperature
Is activated when the ERC senses a runaway heat condition or when the temperature exceeds
“runaway limits”. The ERC will beep until the cancel or another function is selected. If the alarm
repeats the F2 alarm check the oven sensor and wiring after fi rst checking for a stuck relay. If alarm
goes away verify the oven will complete a clean cycle without any type of failure.
Another words the problem with oven sensor or relay board.

Oct 26, 2008 | Dacor MCS130 Millennia Electric Single...

2 Answers

Random beeps, oven almost starts itself


The touch pad may be defective. There is a membrane behind the buttons that will cause problems like that. The only cure is to replace the touch assy.

Sep 11, 2007 | GE Profile JKP18 Electric Single Oven

1 Answer

Dacor Oven Won;t Heat


power surges can short out the electonics in appliances. If you can locate where the tech sheet is and I would say its behind the control panel on top, look at the wiring diagram and see if there are any replaceable fuse's. Or a resetable fuse for the heating element. If not check to see if power is getting to the main control bord. If there is power there you may need to replace the control.

Jul 19, 2007 | Dacor ECS130 Epicure Electric Single Oven

Not finding what you are looking for?
Ovens Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dacor Ovens Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Jaime Hernandez

Level 3 Expert

2267 Answers

Jazz Boyce
Jazz Boyce

Level 1 Expert

728 Answers

Are you a Dacor Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...