Question about Hobart 42 in. AM14C-154 Free-standing Dishwasher

1 Answer

All the wires been trip by some one so i need to wire it up

The wire in the dish washer been trip by some one .so i have started the job . now i need to fix it. i have no wiring diagram wit me.
pliz sent me one so i can work on it
its dish washer HOBART MODEL IS amloos and serial no is
90.032.874

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 109 Answers

Can you confirm if you have an AM14 or AM15. Check the data plate and give the Voltage spec., ML number, if you have it.' Please confirm what you mean by the wires are trip.

Posted on Oct 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to repair my kenmore dish washer not powering on but shocked me before it shut down for good ?


it sounds to me as though you may have a bare wire giving a direct short to the system.therefore by having a hot wire grounding out on the dishwasher body, it is running that current to the dishwasher body where if you touch the dishwasher you will recieve a shock.this also doesnt allow the electricity to go to where it is needed to power your appliance.

May 20, 2014 | Kenmore Dishwashers

1 Answer

Dishwasher trips breaker. Breaker only resets of door is opened


wires rubbing inside dish washer , surprising its not blowing fuse in dish washer plug .

Mar 25, 2013 | Dishwashers

1 Answer

No power lg dishwasher


A large dishwasher should have a dedicated circuit breaker in the circuit breaker panel, check to see if the breaker is on, tripped, or off, it should be on. If it is on, remove the panel cover and check for power coming out of the circuit breaker, if there is power coming out of the circuit breaker, check for power at the dish washer. Checking for power at the dishwasher may involve pulling the connector cord if any and check the power outlet for power, if there is no power outlet and the dishwasher is hard wired into an electric box, the electric box needs to be opened and the wires need to be tested for power, involving removing the wire splice nuts or wire nuts. Once the power is verified to the dishwasher and the washer is still with no power, a fuse should be sought inside the dishwasher control panel or that the power feed wires are properly spliced. A voltage testor is needed to test for power. electric shock hazard on live wires, please be carefull or call out a electrician or handyman if power testing skill is questionable.

Aug 11, 2012 | LG Dishwashers

1 Answer

My dish washer just stopped working, no power no lights no nothing. it is plugged in and the circuit breaker is not tripped the wires for to the plug are tight and i didnt find an loose wires, the gfc plug...


this machine has no power, and i would suspect a broken wire but you say the trip did not trip,have you got a voltage tester?if so set to x1k or until when you touch both points it workes.with the plug in hand put one point on the right plug ter and put the other one on the left if you get a reading that means a broken wire.if you dont then suspect the plug point.if all fails then the main cpc board inside the machine is gone.adrian,,,,

Sep 06, 2010 | GE 24 in. GSD3630Z Built-in Dishwasher

1 Answer

Power overload swith in the house has started tripping when the dishwasher is started


Is this happening only now! If it was working OK earlier and tripping now only it may be due to some electrical fault inside the machine.

Switch off all the high power appliances and try the dish washer. If it works you have to check the breaker overall power rating!

If it trips during dish washer ON, the fault could be in the heater circuit of your machine. Heater Insulation would have become weak etc.

May 17, 2010 | Dishwashers

1 Answer

My dishe washer wont turn on


Make sure there's power getting to the dishwasher. Check for a tripped circuit breaker or a blown fuse. Check the wall socket for power. Sometimes the power cord disconnects at the dishwasher (inside the junction box, behind the bottom kick panel), if this is the case, the wiring must be repaired or replaced

Now, if you have confirmed that the unit is receiving power from the outlet, and the unit is still not responding, this will lead to a failed control board, or timer module. replace either the timer, or control board, in this case.

Nov 05, 2009 | Dishwashers

1 Answer

Dish washer will not start. Program shows that there is power, but it will not start. Door is securely shut. the other day I took the trap apart and saw about 1C of standing water below the silver...


Hi..

If dish washer wont start check this

  • Check for a blown fuse or tripped circuit breaker
  • Check that the dishwasher is plugged in securely
    or
  • Inspect the wiring connection to the dishwasher for burns or breaks.
  • Check the door latch
  • Test the door switch
  • Test the timer motor
  • Test the selector switch
  • Test the motor start relay
  • Test the motor
Check also this

  • Unjam the motor
  • Unjam the pump
  • Test the motor
  • Test the motor start relay
  • Check the drive belt

Good luck !!!

Regards
PCmania

Jul 11, 2009 | Bosch 24 in. SHU66C05 Stainless Steel...

1 Answer

POWER AND ALL THE LIGHTS WENT OUT COULD IT BE A FUSE?


check power to the unit main breaker tripped? if breaker is ok there may be loose wire connection or the fuse in washer machine has blown

Apr 21, 2009 | Dishwashers

1 Answer

Dishwasher is "tripping" the breaker & not draining.


I had the same problem with a Hobart AM8 passthru dishwasher. The electrician determined that some of the wires had become exposed and were wet, thus shorting things out and tripping the breaker.

Jan 08, 2009 | Bosch Dishwashers

1 Answer

Dish washer keeps tripping fuse box


one of your wires is grounding out. not easy to find. i would call a repairman to find it

Nov 25, 2008 | Dishwashers

Not finding what you are looking for?
Hobart 42 in. AM14C-154 Free-standing Dishwasher Logo

186 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hobart Dishwashers Experts

Ricardo311

Level 1 Expert

36 Answers

yadayada
yadayada

Level 3 Expert

60667 Answers

handygirl911
handygirl911

Level 2 Expert

55 Answers

Are you a Hobart Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...