Question about Apple TV MB189LL/A 160GB RTL 160 GB USB 2.0 Hard Drive

Open Question

Apple Tv wont boot up and wont factory restore

Ok here goes...
After following the Apple support web page about connecting an Atv to my Mac via Ethernet it broke. It boots up to the choose language screen and then the restart menu. If I restart it eventually goes back to the language selection screen. Diagnostics say the Atv is working correctly. It wont let me do a factory restore though, it tries and fails.
Any suggestions?

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I watch Netflix on this tv, either through direct streaming or via Mac laptop connect? Westinghouse VR-4030 flatscreen


Go to Best Buy and get an Apple TV for $69. (It's not aTV set. Just a little box that connects to your wifi and streams content to your T v. You hook up the Apple box, change the tv to the hdmi port you plugged it into and get your wifi connected to it. Then select Netflix and log into your account. Or wait for the new Apple to be available for $200. You can also get an Amazon Firestick from Amazon but you will like the $69 Apple TV better.

Sep 15, 2015 | Westinghouse Televison & Video

1 Answer

Trying to activate bps.org and apple TV


Hi James

Not enough details
Plug the AppleTV HDMI cable in and connect it to your TV Screen.
Use the TV Screen remote control to select the screen "input" from the HDMI port you plugged in to.
Turn AppleTV on (plug in)
http://www.apple.com/appletv
The details should show on your tv screen if the correct hdmi input is chosen.
Use the tiny aluminum IR (IfraRed) control to enter details & control your AppleTV.
If you have an iPhone / iPad you can get the "Remote" App for free that is easier to use to set up the ATV.
AppleTV will want to connect to your home WiFi (Modem) Box that you get your internet from. You will need to know the WiFi Password to allow connection to home WiFi. This keeps the neighbours from connecting to your wireless internet.
You then Select the Language and enter your AppleID (e.g. email address & password) same as you use for your App Store for iPhone / iPad etc
Once connected to the internet the ATV will show all the streaming services that are available. Also if you have iTunes on your Mac Computer you can set up sharing and display selected photos as a slide presentation when the ATV is in standby.
There are many sites for troubleshooting ATV.. here is one

https://support.apple.com/en-us/HT200197

A New ATV is expected to be announced on 9 Sept 2015

Hope this Helps Someone.... if so Tik the box.
Cheers
https://duckduckgo.com/?q=apple+sept+9+announcement&ia=news

The next Apple TV What to expect if Apple unveils new streaming box

Mar 17, 2015 | Apple Computers & Internet

1 Answer

Factory Reset Grandstream GXP 2000 w/o using the menu?


From the Granstream User Manual (Page 44):
Restore Factory Default Setting
WARNING: Restoring the Factory Default Setting will delete all configuration information of the phone.
Please backup or print all the settings before you restoring factory default settings. Grandstream is not
responsible for restoring lost parameters and cannot connect your device to your VoIP service provider.
INSTRUCTIONS FOR RESTORATION:
Step 1: Press "OK" button to bring up the keypad configuration menu, select "Config", press "OK" to
enter submenu, select "Factory Reset" (Please refer to Table 5-1 of keypad flow chart)
Step 2: Enter the MAC address printed on the bottom of the sticker. Please use the following mapping:
0-9: 0-9
A: 22 (press the "2" key twice, "A" will show on the LCD)
B: 222
C: 2222
D: 33 (press the "3" key twice, "D" will show on the LCD)
E: 333
F: 3333
Example: if the MAC address is 000b8200e395, it should be key in as "0002228200333
395".
NOTE: If there are digits like "22" in the MAC, you need to type "2" then press "->" right arrow key to
move the cursor or wait for 4 seconds to continue to key in another "2".
Step 3: Press the "OK" button to move the cursor to "OK". Press "OK" button again to confirm. If the
MAC address is correct, the phone will reboot. Otherwise, it will exit to previous keypad menu interface.

https://www.grandstream.com/products/gxp_series/general/documents/gxp_usermanual_english.pdf

Apr 03, 2014 | Grandstream GXP-2000 IP Phone

1 Answer

It has password and I can't open it


Resetting the Linksys Router to Factory Default
To reset the router to its default settings, press and hold the Reset button located at the back of the router for 10 seconds.
IMPORTANT: Older Linksys devices may require pressing and holding the Reset button for 30 seconds to complete the reset process.

kb19584-003_en.png To perform hard reset on your Linksys router, follow the steps below:
NOTE: The location of the Reset button may vary for every model.
If the normal reset does not work, unplug and re-plug the router's power adapter while pressing the Reset button.
You can also reset the router via its web-based setup page. Follow the steps below to learn how.
Resetting the Router Using the Web-Based Setup Page
Step 1:
Access the router's web-based setup page. To learn how, click here.

NOTE: To learn how to access the web-based setup page on a Mac computer, click here.

Step 2:
Click the Administration tab then click on the Factory Defaults sub-tab.

kb19584-004_en.png NOTE: If the screen on your router's web-based setup page is different, click here.

Step 3:
Under the Factory Defaults section, click on the Restore Factory Defaults button.

kb19584-005_en.png The default settings of your router are now restored.

Sep 20, 2011 | Linksys WRT54GX2 Wireless-G Broadband...

1 Answer

Cant seem to connect to the internet local access only


Connect Modem cable to Modem port of the Belkin Router Check the light status Flashing Amber-- Issue with Physical connection (Check Cables) Steady Amber-- Needs to be configured Follow these steps Open Web Browsers like Internet Explroer or Safari Type in Web address bar 192.168.2.1 For Password Leave the BOX blank and click on submit Torwards the left side you can find Restore Factory Defaults Click on it Restore Defaults> Click on OK for Disclaimers Then select Connection Type, then select Dynamic>Host name ( put your computer name)> Click on SUBMIT
Select MAC ADDRESS( towards left side)> select CLONE
Then Reboot both Modem and Router Hope it will fx the issue for You
STEADY GREEN-- Ready to use the internet Flashing Green--- Router is booting up
((((((FOR HARDRESET -- Behind the router you can find reset hole... Press and Hold with any sharp object (toothpick or Paper clip) for 40 secs))))

Dec 09, 2010 | Belkin Basic Wireless Router

1 Answer

I need my wep key


Step 1:
Take note of the current settings of the router before resetting.
Step 2:
Press and hold the Reset button of the router for 30 seconds.

3798-001.png

Figure 1: Location of the Reset button on a Linksys BEFW11S4 router.
NOTE: The image may vary depending on the model number of the Linksys device.

4030-022.png

Figure 2: Location of the Reset button on a Linksys WRT54GX router.

4030-024.png

Figure 3: Location of the Reset button on a Linksys WRT54GC router.
NOTE: If the image of your router looks different from the ones shown above, consult your router documentation.
Step 3:
If the normal reset does not work, try to press and hold the Reset button for three seconds. The Ethernet light should go OFF then back ON. Unplug and re-plug the router's power adapter while pressing the Reset button. Keep holding the reset until the power light stops blinking.
NOTE: The router must be powered ON when you press the Reset button.
To reset the router via its web-based setup page, follow the steps below.
Resetting the Router Using the Web-Based Setup Page
Step 1:
Access the router's web-based setup page. For instructions, click here.
NOTE: To learn how to access the router's web-based setup page using a Mac computer, click here.
Step 2:
When the router's web-based setup page appears, click Administration then click on Factory Defaults.

kb4008-004_en.png NOTE: If the screen on your router's web-based setup page looks different, click here.
Step 3:
Click on Restore Factory Defaults and select Yes.

kb4008-005_en.png Step 4:
Click OK.

kb4008-006_en.png

Nov 15, 2010 | Linksys WCG200 Router

1 Answer

We have had a working router for 2 yrs, until my son pressed the middle button of the router. Now none of our laptops 'recognize' and are unable to connect. Our cell phones that used to connect to WiFI...


I just try to reset the router to factory default settings.Here is how:
Step 1:
Take note of the current settings of the router before resetting.
Step 2:
Press and hold the Reset button of the router for 30 seconds.

3798-001.png

Figure 1: Location of the Reset button on a Linksys BEFW11S4 router.
NOTE: The image may vary depending on the model number of the Linksys device.

4030-022.png

Figure 2: Location of the Reset button on a Linksys WRT54GX router.

4030-024.png

Figure 3: Location of the Reset button on a Linksys WRT54GC router.
NOTE: If the image of your router looks different from the ones shown above, consult your router documentation.
Step 3:
If the normal reset does not work, try to press and hold the Reset button for three seconds. The Ethernet light should go OFF then back ON. Unplug and re-plug the router's power adapter while pressing the Reset button. Keep holding the reset until the power light stops blinking.
NOTE: The router must be powered ON when you press the Reset button.
To reset the router via its web-based setup page, follow the steps below.
Resetting the Router Using the Web-Based Setup Page
Step 1:
Access the router's web-based setup page. For instructions, click here.
NOTE: To learn how to access the router's web-based setup page using a Mac computer, click here.
Step 2:
When the router's web-based setup page appears, click Administration then click on Factory Defaults.

kb4008-004_en.png NOTE: If the screen on your router's web-based setup page looks different, click here.
Step 3:
Click on Restore Factory Defaults and select Yes.

kb4008-005_en.png Step 4:
Click OK.

kb4008-006_en.png

Nov 15, 2010 | Linksys Wireless-G Broadband Router

1 Answer

I had a problem with updating firmaware for OpenComms


Liebert says there is a known issue when you try to upgrade from 2.200 to 2.400, you are supposed to upgrade to 2.300 first or it will lock up when you connect to the network. You have to call Liebert and ask them to send you the 2.300 firmware. Downgrade the firmware to 2.300. Once you have 2.300 on there you can upgrade the card to 2.400 via the web interface and you won't have to mess with the Xmodem upgrade process again. Make sure you follow their instructions for downgrading, there is an extra .bin file that you have to upload to the card first.

Nov 07, 2009 | Liebert OpenComms Web Card (OCWEBCARD)...

1 Answer

Linksys Group LIWRT160N Ultra RangePlus Wireless-N Broadband Router say's password is not enough characters, however I am using the right password. Why can't I set up this Window's computer?


Okay,i only option is to reset the router to its factory settings.
Please follow the steps to reset the router.
The router can be set to factory default by pressing the Reset button of the router and resetting through the router’s web-based setup page. Pressing the Reset button on the back of the router for 30 seconds will reset your router to its factory default settings. Any settings on the router will be erased and the router’s IP address will become “192.168.1.1,” the username is still blank, and the password will be “admin.”
To perform a hardware reset on your Linksys router follow the steps below.
Step 1:
Take note of the current settings of the device before resetting.
Step 2:
Press the Reset button of the router for 30 seconds.
Step 3:
If the normal reset does not work, unplug then plug back the router's power adapter while pressing the Reset button.
To reset the router via its web-based setup page, follow the steps below.
Resetting the Router Using the Web-Based Setup Page
Step 1:
Access the router’s web-based setup page. .
NOTE: If you are using Mac to access the router’s web-based setup page,
Step 2:
When the router’s web-based setup page appears, click Administration then Factory Defaults.
Step 3:
Look for Restore Factory Defaults and select Yes.
Step 4:
Click 4268-009.png

May 18, 2009 | 2wire (1000-100016-002) Wireless Adapter

1 Answer

After running factory restore phone wont boot


Just Download the update service by clicking on the download buttonon this link http://www.sonyericsson.com/cws/support/softwaredownloads/detailed/updateservice/p1i?cc=in&lc=en

After you download install the service and run the update service follow the steps on the screen

Follow the steps and your problem will be solved

Ur Phones Operating System is Currupted that is the reason it is not responding.

Oct 20, 2008 | Sony Ericsson P1i

Not finding what you are looking for?
Apple TV MB189LL/A 160GB RTL 160 GB USB 2.0 Hard Drive Logo

Related Topics:

1,388 people viewed this question

Ask a Question

Usually answered in minutes!

Top Apple Computers & Internet Experts

paulcarew

Level 3 Expert

2180 Answers

Martin Buck
Martin Buck

Level 2 Expert

81 Answers

MarkMAlford
MarkMAlford

Level 1 Expert

6 Answers

Are you an Apple Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...