Question about Cisco Catalyst 3560-24PS Switch

2 Answers

Hi, I have done a reload on my Cisco 3560 switch byy giving these commands. write ersae reload Ever since i have done this i am getting only switch: on my switch. Its not working. kindly help me out. When i power on my switch it shows only switch:

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

  • Expert
  • 103 Answers

If you issued a write erase, you removed the configuration, not the boot image. You will need to re-configure the switch back to the way it was. There is no way to recover the config, unless you have backed it up, or saved a old version under a different name on the flash.

Posted on Mar 12, 2014

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Hi,
This means that switch is in boot mode, In order to boot it use "dir flash:" and see if you can find a valid image in it. if it is there, use "boot flash:<image name>" to boot up the switch. in case there is no image we need to do an xmodem to recover the switch, we need to have a console cable connected in the console port and an image for 3560 on your system, Issue the command " copy xmodem:<image name> flash:<image name> " after this go to transfer file in the menu of hyperterminal and choose " send a file " browse the file and select protocol as "xmodem" this will take around 4 hours to copy and then you just need to enter " boot" and switch will be up.

Regards,

Harshit

Posted on Feb 01, 2009

3 Suggested Answers

  • 139 Answers

SOURCE: no power

Here are a couple of ideas...

Check out ebay item #140197449460

- or-

http://www.cablesandkits.com/cisco-power-supplies-c-63.html

Posted on Jan 18, 2008

ward_knutson
  • 64 Answers

SOURCE: cisco 2960 power supply

The Cisco 2960 has a life time warranty. Contact the seller and they should be able to get the switch exchanged at no cost.

Posted on Jan 19, 2009

  • 39 Answers

SOURCE: I have a cisco 3560 poe switch which does'nt seem

hi,
check physical port and cable itself.

if possible can you reboot that switch.

Posted on Sep 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I connect cable modem to cisco 3560 switch and configure it?


The cable modem will need to go through a router because it needs a NAT and PAT translation table, connecting the cable modem direct would lose the ability to get to the internet.

Jun 05, 2012 | Cisco Catalyst Compact 3560-C PD PSE -...

1 Answer

After unplugging the UTP cable the LED stays,Cisco 3560 Poe 48por


The light may stay on due to static in the switch. It will automatically go off after some time when the static gets discharged.

Apr 29, 2010 | Cisco Catalyst 3560-E 24-Port Gigabit...

1 Answer

Can we able to trunk one vlan to another vlan


interface GigabitEthernet0/1
switchport access vlan X
!
interface GigabitEthernet0/2
switchport access vlan Y
!
interface GigabitEthernet0/3
description trunk port
switchport mode trunk
switchport trunk allowed vlan X,Y

Aug 19, 2008 | Trendware 8PORT SMART POE SWITCH SNMP VLAN...

1 Answer

Cisco Switches and wr erase


No problem. Glad it help you out.
And thanks for the personal note to me.

Ken

Jun 24, 2008 | Cisco Catalyst 3560-24PS Switch

1 Answer

No power


Here are a couple of ideas...

Check out ebay item #140197449460

- or-

http://www.cablesandkits.com/cisco-power-supplies-c-63.html

Jan 18, 2008 | Cisco Catalyst 3560-24PS Switch

1 Answer

How to reset the cisco switch to factory default?


When you say you were able to connect to the switch through hyperterm, were you able to login with the enable password? If not, you cannot reset the factory defaults without the enable password. If you do not have this then search on Cisco's site for password recovery for your model switch. If you did login with the enable password, the command to run for CATos is "clear config all". For Cisco IOS, you have the right command with "write erase". When you issue that command, do you get a "Erase of nvram: complete " or an error? Are you issuing the "reload" command after a successful erase? Be sure you answer No when it asks "System configuration has been modified. Save? [yes/no]:" as sometimes this seems misleading and some people think they mean to save the reloaded default. They are really warning you that you are about to loose the old configuration and attempting to prevent you from accidently erasing it. So answer "no". After a successful reload of the IOS you should also clear any VLAN information. To do this, issue "delete flash:vlan.dat" and then do another "reload".

Aug 29, 2007 | Cisco Catalyst 3560-24PS Switch

Not finding what you are looking for?
Cisco Catalyst 3560-24PS Switch Logo

Related Topics:

603 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cisco Networking Hubs & Switches Experts

Sr. Pelo
Sr. Pelo

Level 2 Expert

72 Answers

Ap12
Ap12

Level 2 Expert

103 Answers

robertmoore1

Level 2 Expert

179 Answers

Are you a Cisco Networking Hub and Switch Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...