Question about InFocus ScreenPlay 7200 Multimedia Projector

3 Answers

''Infocus Demonstration'' logo at upper right hand corner screen

The logo is present as the movie is playing. If you select menu it goes away. As soon as you go back to the movie the logo comes up again. I have done the following. Call infocus tech no help there, Factory reset, Firmware uploaded. Nothing helps. I would like to know if any one has rest codes for the hardware of the infocus sp7200.

Posted by on

3 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

''Infocus Demonstration'' logo at upper right hand - 11_15_2012_7_53_59_pm.jpg

Posted on Nov 15, 2012

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert whose answer got voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 74 Answers

You will need to access the service mode. There is a code that you have to plug in to access it.

Posted on Sep 25, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 2,236 Answers

No reset codes, but the problem lies with the dmd eca, which is the circuit board that attaches the dmd to the main board. this board holds the splash screen ("infocus" screen) info. unfortunately, unless you have the specific part number from the board, you need to replace the entire optical engine, which is the most expensive part of the projector. if you do get the part number, find an infocus authorized service center and purchase it from them.

Posted on Jun 05, 2009

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Infocus projected image is distorted

check the screen resolution settings in visa it maybe different than the desktop settings.infocus can execpt many resolutions but not all. try 1280x1024

Jan 29, 2008 | InFocus ScreenPlay 4805 Multimedia...

1 Answer

Half inch crystal/ solid white vertical line on screen

Adjust the horizontal in the menu then try the overscan adjustment. If the image does not look dim you do not need a lamp.

Jun 04, 2010 | InFocus IN72 Multimedia Projector

1 Answer

Need driver for infocus 4805

goto select your model on the left hand side, select firmware on the menu on the top and follow the directions

Apr 30, 2010 | InFocus ScreenPlay 4805 Multimedia...

1 Answer

Dark in middle , clear in upper and middle left corner

your light tunnel has collapsed and needs replacing. you can get the part and do it yourself, or you'll have to send it in to an infocus authorized service center. try av solutions in ny. they're pretty good.

Nov 02, 2009 | InFocus ScreenPlay 4805 Multimedia...

1 Answer

Infocus lite pro 720

Sounds like the LCD inside is dying and you're losing pixels. Bummer.

Aug 31, 2008 | InFocus LP70+ Multimedia Projector

1 Answer

Infocus x1 image issue

the light tunnel has collapsed and needs replacement. it's only about $10 and fairly easy to replace.

Sep 29, 2007 | InFocus X1 Multimedia Projector

6 Answers

Infocus LP70+ has a small shadow in the right lower corner of the display. Could this be a bulb or lens problem or ??? Thanks for any help suggestions.

the light tunnel is collapsing. it's used to hep evenly distribute the light and make the edges crisp. infocus now calls it an integrator rod (315-0055-xx).

to replace the tunnel (rod):
take the top off, take the screws out of the top and the wires out of the circuit board, take the fans out, take off the colorwheel shield, remove the lens assembly (optical engine), remove the colorwheel, take out the 3 set screws, and slide out the tunnel assembly. then remove the foil around the opening and the screw out of the top, and slide the rod carrier out. now remove the metal clip and the pieces of mirror. replace the tunnel (rod), put the clip back on, and reverse the procedure. now, the 2 set screws on the side are to adjust the image, so do not put them in too tightly, and they must be adjusted while the projector is on and the cover is off.

or give it to someone else to do.

Sep 27, 2007 | InFocus LP70+ Multimedia Projector

1 Answer

Screen goes blank momentarily

cover up the infrared remote sensor on the projector. The heat of these colours or something might be messinf with the infrared remote sensor. TRy this and see what happens. It may just be bad contacts. Some projectors just cant handle stuff like this. Some were meant for presentations and presentations only. BUt seriously try covering the remote sensor to see what happens. If it is an older projector the infrared signal detector might be sensitive to bright light or stuff like that.

Aug 23, 2007 | InFocus ScreenPlay 4805 Multimedia...

Not finding what you are looking for?
InFocus ScreenPlay 7200 Multimedia Projector Logo

Related Topics:

352 people viewed this question

Ask a Question

Usually answered in minutes!

Top InFocus Office Equipment & Supplies Experts

Juan Carlos Pacheco

Level 1 Expert

36 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6370 Answers

Are you an InFocus Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides