Question about Onkyo TX-SR703 Receiver

1 Answer

Speaker is not detected

When trying to set up my reciever for onkyo 706 it starts to calberate but then I get an error spk detect error. I know my speakers work I had a reciever hooked up yesterday and they were all detected. Any other ideas?

Posted by on

  • Anonymous Nov 30, 2008

    same problem. Speaker obviously works but isnt detected.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

If you are connecting a 5.1 surrround sound rather than 7.1, have you connected the surround speakers to the surround left and surround right rather than surround back left and surround back right?

Posted on Oct 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have onkyo reciever tx-ds898 no sound


Some receivers shut down automatically if a thermal overload is detected or more commonly if speaker impedance is less than specified, i.e, driving a 2 ohm impedance speaker with an output rated for 8 ohms. If you can get the receiver operating long enough, you may see a message indicating why it is shutting down

Oct 03, 2012 | Onkyo TX-SR606 Receiver

1 Answer

I have a onkyo 706 reciever and I can't get any TV sound


Component (i.e. TV) should be connected to plug labeled IN (signal IN receiver).

Jul 15, 2009 | Onkyo TX-SR606 Receiver

1 Answer

Power will not stay on


Activated protection circuitry means that the amplifier is seeing conditions it does not like and is shutting down the power to prevent further damage.
Either you have a short in your speaker wires, in your speakers, or a blown amplifier.
Disconnect both speakers and turn on the amplifier. Does it still give the error message? If it does, your amp is blown. If it does not, carefully inspect your speaker wires and their connection. Make sure all looks good and reconnect the speakers and try it again. Still get the error message? You likely have a problem in your speaker cabinet(s).

Apr 21, 2009 | Onkyo HTR500 Receiver

1 Answer

Speaker Detect error Left Rear


Hey there.

I had the same problem until i figured out that if u dont have surround speakers connected it will be a error when trying to configure the rear surround speakers.

So if u are running a 5.1 system and have hooked up ur surround speakers to the back surround speaker port u have to change them to the surround speaker port.

Hope this work for u

Jan 11, 2009 | Audio & Video Receivers

1 Answer

No sound from speaker


Isolate the wiring, too. It's a binary problem. Should be easy. Or try running your suspected speakers on other channels to eliminate amplifier bugs.

Jan 02, 2009 | Onkyo TX-DS595 Receiver

2 Answers

Hi We are setting up our new Onkyo TX SR606 receiver but are having trouble with the automatic speaker set-up. The 2 front speakers, centre and the back right speaker are ok, but there is an error...


Hi there. If you are running a 5.1 speaker system, make sure your surround speakers are on the surround terminal NOT ON THE SURROUND BACK. the surround back is only for the 7.1 speaker system.

Sep 13, 2008 | Onkyo TX-SR606 Receiver

1 Answer

I have an onkyo tx-sr606 with speakers set up at 5-1 channel, when trying to set up the auto speaker set up i keep getting the speaker detect error message. what can i do ?


hi there. try to check if your surround speakers are on the surround terminal. do not put them on the surround back terminal because this is only allotted for the 7.1 speakers. hope this helps.. ^_^

Aug 12, 2008 | Onkyo TX-SR606 Receiver

1 Answer

Onkyo TX-NR905 Protection Circuit Activated


The problem is not with the inputs. This unit is in protect because a problem has been detected in the output section. Try disconnecting the speaker wires and turning it on. If the unit remains on, there is a short in one of the speaker wires. If the unit still shuts down, there is an internal problem that will require repair. It sounds like this is a new piece. If so, it should be covered under warranty.

Keep us posted,
Dan

Jul 28, 2008 | Onkyo TX-NR905 Receiver

1 Answer

Onkyo 875 Audyssey will not detect


no solution from me but just to say i am having exactly the same problem - did you get anywhere with yours?

Jul 10, 2008 | Onkyo TX-SR875 Receiver

1 Answer

Set-up problem with sound and speakers


I sent this TX-SR605 system to an authorized dealer for repair. It seems like it is a very simply problem - the internal set-up mic jacket closed circuit, so the system think the set-up mic is always plugged in (even when physically unplugged it, the system still detect plugged in). And it enters the automatic speaker setup and never quit.

Now I have the receiver back home and tested it. Everything worked O.K. now. It is a pity that this new-bought equipment (just one month) need repair for just a small action of plug in a mic ( I swear I plugged it in very tenderly). It is shame for such a unreliable performance happened on brand name like ONKYO. How can you be confident for an equipment failure in one month.

Dec 25, 2007 | Onkyo TX-SR605 Receiver

Not finding what you are looking for?
Onkyo TX-SR703 Receiver Logo

361 people viewed this question

Ask a Question

Usually answered in minutes!

Top Onkyo Audio & Video Receivers Experts

D. E. Hev

Level 3 Expert

1059 Answers

gbob59

Level 3 Expert

2963 Answers

Matthew Spark
Matthew Spark

Level 3 Expert

1042 Answers

Are you an Onkyo Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...