HelpMe plz Hello frcs68, My AZtech modem DSL605ew is stop wireless connection and internet.But it does not happen every time. When I checked its behavior it is periodically happened in ~30 mins.I switched off and on again its ok sometimes. Another 30 min it did that again.So what that problem is and how can I solve that?

Configure it manually, 8/35, pppoe, username & password... that's it.

Please see this site it might help you...http://www.deviceden.com/manual/aztech/dsl605ew/..This link is aztech dsl manual.

First uninstall the driver.Shut down and restart.If this dont work, shut down and remove the modem.reseat it and restart the PC.If this dont work go to device manager and look for any yellow symbol on the modem properties.If any right click on it and select update driver.

Post back!

It will be lit up if there's a Ethernet Cable Connected to either of the 4 ports. If you will be using a Hardwired connection to connect the Computer to the router you will see that the light on the port where the ethernet cable is connected will lit up. However if you will be using wireless connection then it wont lit up.


Thanks for using Fixya.

Aztech DSL605EW problem internet lite bling power lite red

First!
Do you have a connection in your modem?
if you do, you need to set up the linksys router in DHCP internet set up.
To have access to the linksys you need to go to:
http://192.168.1.1
The password it's admin
and the username in blank (no password)
change the internet setup to DHCP

Make sure you don't have the Same address for 192.168.1.1 or you modem cause if you do you'll need to change the ip address on the linksys router...
:)

Darvin, gotta love your ISP. Never fear......

if it isn't too much of a problem (knowing you have wireless setup done already), then do a factory reset on your router ** remember to copy the WEP Key if you have, or recall the PASS PHRASE so you won't have to reset all wireless devices ** Reset is located on back, you need a ball point pen to reach the reset switch.

Reset process: unplug, take ballpoint pen & insert into reset switch & plug unit back in. Sometimes tricky, but you should notice green light goes to yellow/orange upon resetting.

RESET or NOT - you want the Linksys set for ::

Connection Type - AUTOMATIC (for automatic discovery)
Router IP Address - 192.168.2.1

DCHP - ON, Addresses - 192.168.2.100 and allow 5-50 users
(for security, assign the number of DESKTOP + WIRELESS expected users +1, this way you don't get overrun without knowlege)

Take the cable from Aztech ETHERNET OUT to WAN on Linksys. (usually BLUE) (??) not 100% sure as I have the little silver pocket edition of the same Router. - power cycle (turn both DSL modem & Linksys off for 20 seconds. turn on DSL Modem, wait till it's about as ready as possible, turn on Linksys, should only take 20-30 seconds to power up & recognize.

VERIFY SETTINGS: access router - 192.168.2.1, goto STATUS. you should see IP Addressing, SubNet, DNS1 & DNS2 settings. If you do not, then you have no internet connection.

ALTERNATIVE,

Setup Linksys Router with COnnection Type: PPoE, you will need your ISP assigned ID & Password. Follow all other instructions properly.

If you still have problems, please contact me at 906-495-1707 or via Yahoo IM [email protected] or through this website.
once

hey there, can u acces the gateway of the router

192.168.1.1 than enter ur login & password

than reset the router to fabric setting when done go back in the router and configure it as u like to have it

Why my Internet exists red light....

Hi Andy,

The WAN port on your Aztech DSL600EW (by default) is configured to be automatically assigned an IP address when connected to a cable modem (Motorola). Connect the WAN port of the Aztech DSL600EW to the Ethernet port of the Motorola, then configure the Aztech for wireless connectivity to your laptop as per the manual instructions.