Question about Toshiba 36A50 36" TV

1 Answer

Time warner code for Fujitsu 42" tv

I have a Fujitsu plasma TV. My Time Warner DVR box was defective and they replaced it. I can not get my time warner remote to program to my TV. My Time Warner DVR box is in another room with other equipment and I am using an infrared to communicate with the equiptment in the other room. I have tried to program it using 0584, 0197, 0051, 0193 and run it manually. Is there any other code or what do you suggest I try? The remote works when I point it at the TV

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have the 55 inch. try using 246. That works on mine. if not try 028,164,208,066
let me know if that works for ya
ric
another note, are you using the flash on the back of your cable box or do you have a sensor in front of the DVR box?

Posted on Dec 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Tv remote codes time warner cable


275,270,274. Try these codes. If you wish to get more, try the following links. Both the sites linked have set-up code list & set-up procedure to many popular brand remote controls. Surf the sites with patience.
http://electrohelponline.blogspot.com/
http://electro-medical.blogspot.com/

Jan 29, 2014 | Broksonic Standard (CRT) Televisions

2 Answers

Where is "set" button on the remote so I can set DVD code?


You need to be using the TV's remote, not the Time Warner remote.  You are reading the TV's manual to set it's remote, not the Time Warner remote.  If you want the Time Warner remote to operate the TV, you will need to find the instructions that the Time Warner box/receiver provides and enter the TV's code.

Mar 24, 2009 | Toshiba 36A50 36" TV

1 Answer

TV is hooked up to Time Warner DVR when I turn on the TV it shows searching for signal but will not allow me to change channells


It will not let you change channels until the signal locks on. If it just keeps searching for the signal, look for a reset button on the dvr. If not, pull the power for 20 seconds to reset the dvr. IF it still wont find a signal, there is a major problem and you should call your satellite provider.

Aug 09, 2010 | Haier Standard (CRT) Televisions

1 Answer

How do i program my new tv code into my time warner remote


Go to the time warner website, they should have accessory section there page, and there you find codes.

Nov 20, 2009 | Toshiba 36A50 36" TV

1 Answer

Wii hook up to time warner cable box with a dvd


I needed another part... an RCA cable splitter to put two cables into the same TV connection.

Nov 09, 2009 | RCA Standard (CRT) Televisions

1 Answer

Remote Code for Orion to Time Warner Remote


Hey,
I've got 3 codes actually...
Try them won't you 0179, 0236, 0463
Hope this helps.
Thanks

Apr 15, 2009 | Orion1934 19" TV

1 Answer

Can't program the DVR remote to cut my broksonic tv on or off.


what is the code for broksonic universal remote code

Jun 20, 2008 | Broksonic CTGV-5463TCT TV

2 Answers

Picture in picture problem


When you use the Time Warner Digital box, you're using the tuner inside that box rather than the tuner inside your TV to select a channel. Picture in picture TV's have two tuner's inside so you can view two channels, but they can only tune the analog channels from your cable company, and only if it's hooked up in a manner that will permit this to happen.

So you only have one digital tuner (the Time Warner Box) so you can only view one channel at a time even though your TV supports Picture in Picture.

It MAY be possible to have limited use of the PIP if you connect your TV in a different way. Your Time Warner box is most likely connected to your TV set with composite cables, those are the Yellow, Red, White cables. If you buy a coaxial cable splitter and split the cable before it goes into the Time Warner box you can then run a coax cable into both the Time Warner box and the coax input on your TV. This would allow you to tune the analog Time Warner channels with both of your TV's tuners. In my area I think the first 60 channels or so are still available in analog, but there is no way to watch any of the higher premium channels without the Time Warner box.

If you go through these steps and you select the coax input on your TV your PIP will work on the lower channels. It MAY be possible to tell your TV to display the input from the composite cables on one of the PIP screens and the input from the coax on the other, but I kind of doubt it.

I know this sounds complicated and if you're not familiar with the way all this works it is complicated. The reason lots of people won't respond to this kind of question on this site is because there is no easy fix and by trying to help I run the risk of getting a bad rating. I don't get paid for this, I just like trying to help, so if I have not explained this in a way that's helpful to you please ask some additional questions before you give me a bad rating. Thanks.

Jan 01, 2008 | Panasonic CT-32D31 32" TV

6 Answers

Codes to make my Time warner remote control the tv


Here's the list from Time Warner

http://www.timewarnercable.com/Carolinas/site.faqs/Equipmenta/Remotes/Digital-Remote-TV-Codes

Oct 26, 2007 | Toshiba 36A50 36" TV

Not finding what you are looking for?
Toshiba 36A50 36" TV Logo

153 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toshiba Standard (CRT) Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

 Elex
Elex

Level 2 Expert

49 Answers

Cindy Wells

Level 3 Expert

4753 Answers

Are you a Toshiba Standard (CRT) Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...