Question about Onkyo TX-SV414Pro Receiver

Open Question

Onkyo tx-sv515pro will not turn on

Unit will not turn on the light for the remote is on .the fuse look good please help

Posted by on

  • barnesmar Feb 14, 2009

    hello--i am currently working on two tx-sv515 pro receivers

    i will let you know what i find wrong with mine as soon as i discover the problems.

    one wont even come on--other one has problem with right output--very weak

    henry

×

5 Suggested Answers

  • 1 Answer

SOURCE: Onkyo tx-vs515pro won't turn on

doubt that reset will fix your problem---but here it is if you want to try:
hold down the cd button and press the power button [at the same time]
test will [should] appear on screen for about 5 seconds--you need to unplug the set during this 5 second period. this resets the cpu chip.
hope it helps solve your problem.

barnesmar

Posted on Feb 15, 2009

  • 13 Answers

SOURCE: how powerful loudspeakers can my Onkyo TX-SV444 tackle, maintaining good sound?

buy 6ohms or 8 ohms speakers. 4ohms consume too much power and sometimes causes short circuit. (safety first!)

Posted on Mar 04, 2009

  • 239 Answers

SOURCE: remote code for sony playstation 3

you cannot control a ps3 with that remote because the playstation 3 only works with bluetooth. I'm sorry to have to tell you. you can purchase a remote that works with your system at any that sells your system.

hope this helped
please rate well.

Posted on Mar 06, 2009

  • 1 Answer

SOURCE: What remote control code does the Onkyo TX-SR304 use?

From: http://www.comcast.com/remotes/universal.html - only worked for me when I had AUX setup with 30135

Unlocking Volume Control For A Single Device (Individual Volume Unlock):

  1. Press a desired mode key where you want volume to be unlocked (e.g., AUX) and controlled within its own mode.
  2. Press and hold SETUP until the selected mode key blinks twice, then release SETUP.
  3. Enter 9- 9- 3 and then press VOL- once. The mode key will blink four times confirming unlock.
    If desired, repeat steps I to 3 (of this section) for each device that you want volume to be unlocked.
Now, after you select a device that has volume unlocked (e.g., AUX), pressing VOL , VOL-, or MUTE will control the device's volume only in its own mode.

Posted on Apr 15, 2009

  • 1 Answer

SOURCE: Program Time Warner Remote RT-U62CP-1.17 to work ONKYO TX-SR575

time warner does not supply the codes. the equipment manufacturer supplies the code to the remote makers

Posted on Jun 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Denon AVR-1908 won't power on


Are you getting a standby light at all? Is it flashing? Do you here a click when you plug the unit in? If the answer is no to all of these then you blew a fuse. If you do have soome sort of standby light, then your set is in protect mode. More than likely for a blown channel. If no lights, but you ar egetting a click, you could have a bad transformer. Use a DVM and see if it is open or not. Good luck

Aug 23, 2012 | Denon AVR-1908

2 Answers

After working perfectly for 2 months, now receiver won't turn on either manually or with remote. Please help,


is it getting power, if so check the manual for an internal fuse. you might have over heated it.

Mar 12, 2011 | Sherwood RX-4109

1 Answer

I have an Harmon Kardon AVR 85 and the power will not come on. The batteries are good in the remote, I have unplugged and plugged the unit back in, but the red light stays on and will not power up. How...


First of all, if you have just been powering up with the remote, try pushing the actual button on the unit. From owning a HK receiver, I found out that if the power switch is out, it will not turn on from the remote. Duh moment when I discovered this.
It also might be an internal fuse or circuit breaker that is shorted or tripped. If there is not an outside breaker or fuse, send this to a repair person. Sometimes there are capacitors in the power amp circuit that can hold a lot of voltage for a good length of time. You could get shocked. So, you might want to let the repairman handle this. Otherwise check for an outside breaker or fuse, and replace if needed.
You can also check Harmon Kardon's site for customer support.

Feb 19, 2011 | Harman Kardon AVR 85

1 Answer

Onkyo tx-ds787 6.1 channel receiver won't turn on? no light nothing!


Check the fuse inside the unit. If there is no power lights, the power supply may be bad - the fuse is located in the power supply. Check you wall outlet, too.

Dec 04, 2010 | Onkyo TX-DS787 Receiver

2 Answers

How to program remote control?


Your Onkyo TX-SR304 receivers remote (RC-645S) is not capable of controlling devices by other manufacturers. It controls only Onkyo devices.
Other Onkyo remotes do have universal remote functionality and you can download Onkyo remote codes here.

I hope that helps.
________________________________________
Download Onkyo TX-SR304 users manual here.

Mar 26, 2010 | Onkyo TX-SR304 Receiver

2 Answers

Unit is plugged in, I have no power


TAKE COVER OFF AND CHECK THE FUSE ,,PUT IN A NEW ONE,,RADIOSHACK

May 15, 2009 | Marantz SR7001

Not finding what you are looking for?
Audio Players & Recorders Logo

Related Topics:

672 people viewed this question

Ask a Question

Usually answered in minutes!

Top Onkyo Audio Players & Recorders Experts

Dennis McCollum

Level 2 Expert

137 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

 Grubhead
Grubhead

Level 3 Expert

4678 Answers

Are you an Onkyo Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...