Question about Computer Monitors

1 Answer

Posi flex pos

I have a posiflex touch screen and the other night it just went dark..power on, fan working, card swipe beeps..but no screen or at times very very very dim. Sorry, I don't know the model #. Also, it is not the dimmer/brighter button.

Posted by on

  • Michelle Adams
    Michelle Adams Nov 10, 2008

    Does anyone know if that is an expensive repair?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

The monitor's back light is out---defect from HP.

Posted on Nov 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HP TouchSmart 310-1125f display is black


Hearing fans and hard drive spin up doesn't necessarily mean system is working - just without video. If you heard a POST beep or the Windows Startup sound that would be different - and good. Is there any video on the screen at all, even just a blinking cursor in upper left of display? If not, your problem is probably hardware such as ram or motherboard. If this system has a VGA or HDMI output to connect to another monitor or TV would be a good check, but AIO system usually don't have that option. Other than that, and this is a shot in the dark: Ensure the system is off, disconnect the power plug, and hold the power button in for 30 sec for a power reset. Then plug in system and try powering it up again. If no go, you may have a hardware problem and will need a PC Tech. Hopefully it is just loose ram.

Apr 08, 2015 | HP Touchsmart 310-1125f Windows 7 4gb Ram...

1 Answer

Laptop screen went dark


Flex screen cable is broken and need to be replaced.
OR
Graphic card chip is overheating and need to be repaired.

Feb 15, 2014 | ASUS Computer Monitors

1 Answer

Touchscreen calibration


does lightly swiping your finger across the screen from the bottom left corner across to the upper right corner? there are different swiping motions that perform commands.

Dec 04, 2013 | Elo Computer Monitors

2 Answers

Raymarine E120, after 4h on display went dark in


blubaju, probably cold-cathode-fluorescent-lamp backlight failure! if unit dosen't have electro-luminescent style backlighting. All LCD panels require WHITE light to see what is on the screen!!! Is same common problem that computer (pc) lcd monitors suffer from!!! I suspect that if your unit has CCFL's, that the SMPS power supply or CCFlamp INVERTER circuit has a problem common to ALL LCD monitors. I should think that any BIG TIME tv/monitor repair shop could examine the printed circuit boards and effect a repair for you! Just mention that you think it suffers from the BLACK SCREEN of DEATH syndrome!!! Also mention that to RAYMARINE!!! when you call them and **** them out!! 12fixlouie .5hr nrth/wst of Windy City Rate this on fixya if this msg helpful??

Nov 16, 2009 | Raymarine M1500 15 in. Flat Panel LCD...

1 Answer

I HAVE A DELL DESKTOP THAT BEEPS WHEN I START IT


The new RAM memory is the culprit. Remove the memory and insert and test one at a time. Either they are different from one another or not the right memory for your system. If neither modules work, put back your old memory and see if the problem disappears.

Hope this helps.

Aug 17, 2009 | HP Compaq WF1907 Monitor

1 Answer

I have an HPa6700y I purchased about three months ago.  At the time of purchase I installed a high-end graphics card myself (ASUS EAH4870 DK/1G Radeon HD) and it had been running beautifully until...


usually there are 2 problems: 1. a vga card overheat when running 3 games the vga card heats up. try using an case fan or adn a vga fan. 2. the game uses a high refresh rate in this case tri to set a default refresh rate from the vga driver. hope this helps

Jun 14, 2009 | Computer Monitors

1 Answer

Blank screen on AL 2223W


When you switch on the computer and monitor does the monitor power light illuminated?
If not check the power cable, if the power light is on try connecting it to another computer, if it works on another computer then the fault is in your computer or a faulty video cable (try another video cable).
If the monitor does not work then it is faulty, if it is OK then your computy is faulty.

If the fault is in your computer, you didn't exactly pinpoint the nature of your fault.
Does the power light on your computer illuminated when you power up?
Does your computer actually boot up, does it give and beep code (count the number of beeps - 7 beeps usually means video problems, depends upon the type of BIOS)?
When your computer first boots up and you see POST information on the screen then nothing, it is most likely :-
1. The refresh rate of the video card has been set too high beyond the monitor's specification.
2. Video card configured with incompatible monitor.

If you computer fires up and the monitor is OK the you have a faulty graphics card, you need to replace it.

Nov 12, 2008 | Acer Monitor

2 Answers

Monitor dark PRoview PL916s


try to contact an expert technician of monitor maybe there is a part of your monitor that is already defective, the controller of brightness and contrast.

Jan 14, 2008 | Computer Monitors

Not finding what you are looking for?
Computer Monitors Logo

Related Topics:

539 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computer Monitors Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18298 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Computer Monitor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...