Question about Pyle PLA2200 Car Audio Amplifier

1 Answer

Car system i have a pyle pla 2200 1400 watt 2 channel amp and a jvc headunit i cannot figure out to hook up the amplifier to my lanzar pro max subwoofers.how do i hook the subwoofers to my amplifier in the bridge formation? ...

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

If you have dual voice coils connect on each seporate sub negative left channel to possative right channel of the subwoofer same to other sub then conect the left possative and the right neggative to your box power terminal same to other sub then conect the two sub outs on your box left speaker positive to your positive left channel bridge then conect left speaker negative to the right speaker possative then connect your right speaker negative to your right channel negative brigdeg to your amp is single coil hook the box its self up the same way to your amp i have two dual voice cooil 12" hooked up to the same amp that way and it rocks without the power protecter turning on

Posted on Feb 09, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On a lanzar 535n 5 channel 3200 watt amp what is the best way to hook up 2 lanzar max 12 inch duel voice coil subwoofers


If your amp allows it hook the the sub's to the first two channels but bridge it and only run it on 2ohms so you don't blow your sub's

May 29, 2015 | Lanzar Car Audio & Video

1 Answer

I have a lanzar vector VCT-2210 2000 watt amp hooked up to two menace 1300 watt subs. when i turn the volume up on the head unit the amp goes into protection mode. i checked all my wiring and it seems all...


Things to check: Is the wire between the amp and the subs heavy enough to pass 167 amps? 2000 * 12 = 166.66666 amps. Max volts on the subs are 10 volts....close enough. Are you sure you're using the line out on the head unit? You may be over driving the amp if it's anything else.If the head unit doesn't have line out connectors then you'll need to get an attenuator for each channel. Do you have caps on the 12 v power in wires? They'll keep the headlights from dimming and the alternator will last longer if you do.

Apr 09, 2014 | Lanzar VCT2210 Vector Series 2 Channel...

1 Answer

How can i hook up my 2 pyle pla 2378's to a sony cdx gt09 cd player and get the maximum wattage from my subs


your amp should work with any cd player. the only way to make sure to get maximum wattage out of your subs, is to make sure that they are wired properly to get the correct impedance at your amp

Oct 16, 2012 | Pyle NEW PLA2378 2000W 2 CH CAR AUDIO...

1 Answer

My pyle 2200 1400 watt 2 channel amp wont get power..... why!!!!!


did you check the remote turn on wire connection at the back of stereo?

Jan 15, 2012 | Pyle Car Audio & Video

1 Answer

Is the pyle pla-1200 bridgable?


This appears to be the manual for several amps, including the pla1200
http://www.pyleaudio.com/manuals/PYLEChopperamps.pdf

If your amp is the same as in this manual, it is a mono amp (or one channel) amp. There is no need to bridge with a mono amp as it has only one channel. The diagram specific to pla-1200 is on page 20 of the manual.

Feb 27, 2011 | Pyle PLA1200 Car Audio Amplifier

1 Answer

2 ohm speakers wont work on a lanzar max pro 4000 watt


The 2 ohm stable rating on the amp is PER channel meaning that you could effectively hook up a 2 ohm speaker or a 2 ohm load to each channel without the amp getting f"d up-butin bridged mode it will only be 4 ohm stable. to achieve a 4 ohm load with your sub the type x wire the coils in series that will get you at 4 ohms to run in bridged mono .But you will get the exact same amount of power if you wire each coil to one channel of the amp as bridged mono sees the sum of your 2 ohm channels combined-Hope that helps.

Jun 08, 2009 | Lanzar VIBE266 Car Audio Amplifier

1 Answer

What is wrong with my system


wiring may not be the problem but try connecting each coil to separate channel and make sure polarities are correct.

Aug 08, 2007 | Pyle PLA2200 Car Audio Amplifier

Not finding what you are looking for?
Pyle PLA2200 Car Audio Amplifier Logo

214 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pyle Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4823 Answers

The Knight
The Knight

Level 3 Expert

73150 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7029 Answers

Are you a Pyle Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...