Question about Hoover Nextra HNWL 3126 Front Load Washer / Dryer

1 Answer

Hnml 7136 it has never realy worked properly and should have sent it back. But never had the time to deal with it. The old problem is that the machine fills up with water and just never stops it gets stuck but this problem is erratic. I have to stand over it and check that it is filling properly. if it doesn't stop filling after the first 10 minutes i have to stop the machine and then drain it then put it back onto a wash cycle. and keep doing this until it works properly. However, the new problem is the tumble dryer. Every thing works, goes round etc except there is no heat! Really fed up with the i ditch it or is it fixable?

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 24 Answers

Sounds like the waste pipe is too far down the stand pipe

Posted on Aug 05, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I need a manual for a singer sewing machine model 7136

You can download your manual free at the Singer Sewing Machine site.

Jan 08, 2012 | Singer Sewing Machines

1 Answer

American-Retro coca cola machine Model AR-15002. fan motor not working due to manufacturer defect... fan blade was not aligned properly causing it to spin occasionally, not properly cooling fridge motor...

Call American Retro and ask for Dave Johnson (the Owner) 559-595-1339. I also had the fan go out on mine and was able to get the part from A.R. Now the heat exchange has gone out and it is back in the shop again and I had to threaten them with a law suit to get them acting on it. Their warehouse person where the parts are has no working knowledge of this machine or what you want when you call for a part, very hard to deal with. I suggested they train them and list a schematic of the machine in the warehouse. I also requested a schematic for the machine for any future problems. I love the machine when it is working! Had mine about 8 yrs or so, bought it right when they were introduced to the market and am looking for many more years service once we get it fixed!

May 19, 2011 | American Retro Coke Machine AR15002...

1 Answer

I have a (time Warner) package deal that consist of cable vision internet telephone & voicemail. I am trying to get the fax machine to work along with these items. My voice mail picks up on the 5th...

Here's the link to download the Lexmark X4270 User's Guide: If you prefer to have the printer pick up faxes automatically, I suggest you configure the printer to pickup after the 2nd or 3rd ring before your voicemail picks it up. On the User's Guide, go to Faxing, Receiving a Fax for the instructions. For more info about the printer, go through the User's Guide. Hope this helps.

Jul 12, 2010 | Lexmark X4270 All-In-One InkJet Printer

1 Answer

Janome 10000 i year ago shaft bushing was replaced . After getting machine back Lcd screen acted up did not think much about it because it was not consistant.less than a year later with very little use...

I have been dealing with machines of various types all my working life. I have learned coincidences do happen - but not very often.

My instinct, in your case, strongly suggests the problems are connected. My instinct is to suggest you take your machine elsewhere for maintenance - somewhere that employs experienced and qualified engineers and has a boss that allows them adequate time to do their work properly.

I am completely guessing but if the replaced bushing was broached or line-reamed or the correct service tool was used for fitting, the dc motor might have survived (these are usually almost bullet-proof). I guess if the dismantling and reassembly was suitably careful, the lcd screen would probably have been in the same condition when it arrive back from repair as when it was sent.

Jun 03, 2017 | Janome Memory Craft 10000

2 Answers

The monitor isn't working on t5048 all I get is the monitor is working

can you tell me more about the computer. Does it display anything at all?

Feb 16, 2010 | E-Machines T5048 (7136) PC Desktop

1 Answer

The factory eithernet card went bad says local

Remove the old card because it is causing the problem. Use the new one. Be sure your computer is turn off while doing this. Hope this could help you..

Oct 24, 2009 | E-Machines T5048 (7136) PC Desktop

1 Answer

All the audio drivers seems find but i cannot get any sound this happens after i had to do a recovery

there are many cause 1/sound softwere not install properly.2/ u may keep sound option in mute. speaker volem may be off and speaker is not well connected with computed.speaker has gon out of work ----thanks

Jun 13, 2009 | E-Machines T5048 (7136) PC Desktop

1 Answer

Problem with panelboard on New Home Memory Craft 800. Need a telephone number or address for repair. Mother's Daughter

This panel must be rebuilt before it will work properly. Unfortunately, it must be sent to Janome Corp. the manufacturer of this machine and they will only deal with their authorized dealers..Find a local authorized Dealer by going to ( and look at the Dealer Locater.
This repair is probably going to cost more than $300 and all the covers have to come offthe machine to remove this panel. Have them service it at the same time. It shouldn't cost that much more.
This is a good machine and if you really don't need BIG embroidery then there's no reason to trade it in.

Apr 24, 2009 | Sewing Machines

Not finding what you are looking for?
Hoover Nextra HNWL 3126 Front Load Washer / Dryer Logo

175 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hoover Washing Machines Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1474 Answers

shaun taylor

Level 3 Expert

1527 Answers

Are you a Hoover Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides