Question about HP Photosmart 3310 Printer

1 Answer

Remove error how to resole error ocx18a0001

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 36 Answers

Hi

reinstalled the software and cable also it will work...

Posted on Nov 18, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can i resol the error h4-00 manual


clear>interupt>0>interupt>1>4>start button>1>start button

Apr 30, 2014 | Sharp AL-1655CS Copier

2 Answers

Check print path error after belt replacement (HP 1055)


Did u observed the belt having 50% vertical tracks & 50% horizontal tracks?. The vertical tracks as well as horizontal proper position?.. understand the snap., re install the belt once again as shown in fig... i hope UR problem will be resoled..



117329c9-d148-414f-9c06-fc5003b1976f.jpg

Apr 15, 2014 | HP DesignJet 1050c plus InkJet Printer

1 Answer

Error code E000 on canon photocopier means


the thermal switch is open. you need to check this part first and if it's open you have to replace it and then erase the E code in service mode-function-error-ok.

Apr 15, 2012 | Canon NP 6050 Copier

1 Answer

Last night the screen of my HP T1120ps Design Jet (42") plotter appeared blank and frozen, but still illuminated. I tried turning the plotter on and off and pulling out all of the ink cartridges and...


Thanks for choosing me:As per you info its formatter or Main PCA faultyPl follow:Step 1: Switch off the printer detach power sources, unscrew both screws take out formatter assembly gently, switch on the printer observe the same symptom? swich off the machine wait for couple off minutes, refix formatter back tighten screws properly.. power it..check...Step 2: Take out formatter as above said remove & refix hard disc mounted on formatter.. fix it back.. check..Step 3: replace formatterStep 4: replace Main PCA..** Most of the cases I found refixing the formatter resoles this type of issues in this series..Be patience best of luck.. Pl see the snap shot of formatter..Vinay 1_27_2012_9_15_36_pm.jpg

Jan 27, 2012 | Printers & Copiers

1 Answer

Ink system failure, won't reset, won't respond to cleaning


Hello,

The "Ink System Failure" error is causes by air in the ink feed tubes. We have a step by step guide purging the air from the feed tubes posted on our web site. Go to our site at: www.ccl-la.com , click on the printer repair link and then the HP link. Follow the steps and you should be back printing in no time at all.

I hope this helps, If so please rate our solution.

Buddy
Corporate Computer
www.ccl-la.com

Dec 31, 2009 | HP Photosmart C6180 All-In-One InkJet...

1 Answer

My HP Photosmart C4280 All in one is all of a sudden making a loud clicking sound when I print. It just started doing it when I printed the next page.


>an unusual noise in the printer could be problem with printing mechanism or a carriage is jammed, try this steps about carriage jam and see if this will resole the issue

http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01309787&cc=us&lc=en&dlc=en&product=3192753

Oct 03, 2009 | HP PhotoSmart C4280 Laser Printer

1 Answer

HP deskjet 5940 printer - lights flashing rapidly and not responding.


>flashing lights or a cobination of lights blinking on your printer will tell you exactly what the problem is, go to this link and see the steps on resoling the blinking lights on your printer
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00394958&cc=us&dlc=en&lc=en&jumpid=reg_R1002_USEN

Oct 03, 2009 | HP Deskjet 5940 Photo InkJet Printer

3 Answers

Error 58.04


This is from the service manual and should help you determine if you need to call in for service. If is in warranty I would anyways since the fuser would be covered if at fault.

58.04 ERROR To continue turn off then on. The low-voltage power supply has experienced an error.
1. Reinstall the fuser. Check the connector
(J1901) between the fuser and product.
Replace the cable or fixing unit if the
connector is damaged.
2. Reconnect the connectors of the fuser
control PCA (J303, J305) and the DC
controller PCA (J107).
3. Replace the fuser. See Fuser
on page 191.

May 03, 2009 | HP LaserJet 5200tn Printer

1 Answer

Cant do EEROM setup coz severe error:0x4010008 occured


restart the plotter in service mode using following method
1 power off the plotter
2 press Up Arrow + Enter Button ( green buton) and while pressing both buttons switch on the plotter
3 when u see service test /Service utilities release keys & select service utilities & then perform eerom setup there , put the actual model number ( c7780b/c ) and it wil resole the issue

Mar 30, 2009 | HP DESIGNJET 800 42IN 1200DPI 96MB PAR USB...

Not finding what you are looking for?
HP Photosmart 3310 Printer Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Printers & Copiers Experts

kakima

Level 3 Expert

96417 Answers

k24674

Level 3 Expert

7987 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you a HP Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...