Question about NetGear RangeMax WPN824 Wireless Router (WPN824NAR)

1 Answer

Reset my router netgear

HOW TO RESET MY ROUTER NETGEAR WPN824v2

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 143 Answers

Just press the reset button at the back of your router (there's a tiny hole near the ethernet ports, you need to use a pin or a paper clip) for like 30 secs to a minute and power cycle it. (note
you can also do a software reset, just follow the steps below:

  1. Type 192.168.1.1 in a Web browser
  2. Click on Backup Settings
  3. In the Revert to Factory Default Settings click Erase
Note: Do not try to go online, turn off the Router, shutdown the computer or do anything else to the Router until the Router finishes restarting! When the Test light (looks like a check mark) stops blinking, wait a few more seconds before doing anything with the Router.

do remember that all your settings will be deleted once you reset the router.

hope this'll help you

ciao

Posted on Nov 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Need to reset netgear router wpn824v2


Don't tell me you tried to upload the firmware from a wireless connection.

It's probably bricked. You could act stupid and send it back to Netgear, claiming it just died...(it did right?) and in the meanwhile, Staples is selling 624's for $40 this week.

Carl

Jul 05, 2009 | NetGear RangeMax WPN824 Wireless Router

3 Answers

How to reset Netgear RangeMax NExT Wireless Router WNR834B


Do a hard reset (20sec hold reset button, unplug for 20 sec still pressing the reset button and another 20 sec to turn on the power while holding the reset button). That should reset to defaults.

Jul 04, 2009 | NetGear RangeMax NEXT WNR834B Wireless...

2 Answers

Cannot login and have reset....


use the console cable . By using this u can able to go inside the router and after going inside just give the respective IP and after giving the ip to the router u can access the router by using Internet Explorer .

Jun 02, 2009 | NetGear DG834G Router

2 Answers

I cannot reset my router by pressing the reset


Check with your browser if the router has been reset. If not your unit must be replaced.

Apr 10, 2009 | NetGear WGR614 Wireless Router

1 Answer

Netgear WPN824v2


If the default username and password is not working you wont be avle to access the router setup page, so the next step that you need to do is tor eset the router and reconfigure it back, to reset it press and hold teh reset button of the router for 15 seconds while the power is ON then after that the default username and password should be working...

Nov 08, 2008 | NetGear DG834G Router

2 Answers

Netgear wireless router reset


You can reset your Netgear router/wireless router to the factory settings from within the router manager. The reset procedure removes all user-configured settings and returns the router to the original factory settings.

For this reason, only reset the router if you encounter problems that can't be solved with other methods.

Step 1: Check that your Netgear router/wireless router is properly connected with your system or not. If it is OK, then press reset button on Netgear router for at least 10 seconds. The 'test' light should flash during this process.

Step 2: Now open browser and enter Netgear's IP address into the address bar. Generally, '192.168.0.1' is the Netgear router IP address but you can find specific IP address in Netgear router manual.

Step 3: Now enter your default username and password to log in to router.

Step 4: Click 'Erase' button under the 'Revert to Factory Default Settings'. This process will erase all your previous changes that have been made to the router and restore the configuration settings to factory setting. Don't interrupt the process until the process is finished.

Once the router's 'test' light has stopped blinking and the configuration page you are on has refreshed, the router has been reset.

Feel free to get instant online Netgear router
support at http://www.vtechsquad.com/netgear-router-support/ to fix Netgear router/wireless router issues.

May 29, 2008 | NetGear WGT624 Wireless Router

1 Answer

Netgear wpn824v2


Plug your modem into the Internet port on the router, plug in any computers that will be hard wired. Open Internet Explorer and type http://192.168.1.1 This will start up the Netgear install wizard.

May 22, 2008 | NetGear RangeMax WPN824 Wireless Router...

2 Answers

Reset


You can reset your Netgear router/wireless wpn824 router to the factory settings from within the router manager. The reset procedure removes all user-configured settings and returns the router to the original factory settings.

For this reason, only reset the router if you encounter problems that can't be solved with other methods.

Step 1: Check that your Netgear router/wireless wpn824 router is properly connected with your system or not. If it is OK, then press reset button on Netgear router for at least 10 seconds. The 'test' light should flash during this process.

Step 2: Now open browser and enter Netgear's IP address into the address bar. Generally, '192.168.0.1' is the Netgear router IP address but you can find specific IP address in Netgear wpn824 router manual.

Step 3: Now enter your default username and password to log in to router.

Step 4: Click 'Erase' button under the 'Revert to Factory Default Settings'. This process will erase all your previous changes that have been made to the router and restore the configuration settings to factory setting. Don't interrupt the process until the process is finished.

Once the router's 'test' light has stopped blinking and the configuration page you are on has refreshed, the wpn824 router has been reset.

Feel free to get instant online Netgear router
support at http://www.vtechsquad.com/netgear-router-support/ to fix Netgear router/wireless router issues.

Dec 15, 2007 | NetGear RangeMax WPN824 Router

Not finding what you are looking for?
NetGear RangeMax  WPN824 Wireless Router (WPN824NAR) Logo

Related Topics:

155 people viewed this question

Ask a Question

Usually answered in minutes!

Top NetGear Routers Experts

Barry37

Level 1 Expert

31 Answers

MrNutsy

Level 1 Expert

36 Answers

Phillip Whisenant
Phillip Whisenant

Level 2 Expert

120 Answers

Are you a NetGear Router Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...