A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones). click here to download the app (for users in the US for now) and get all the help you need. Good luck!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
It may sound strange but be absolutely sure the cable is plugged into the monitor. Adapter on the computer.
The serial adapter on the back looks just like video.
Video actually has a faintly noticeable monitor icon rigtht next to it.
Plugging into a serial can eventually blow out your monitor.
Also, a.badcable can do the same thing.
And if you have messed up the monitor's settings you will see the same
Red (foil wrapped with 1 bare ground wire) Green (foil wrapped with 1 bare ground wire) Blue (foil wrapped with 1 bare ground wire) Transparent (foil wrapped with 1 bare ground wire)All the above go to the corresponding Gun Color, the Bare wire goes the one GND pin. Purple Yellow Black Orange White Bare braided outer ground wire. Combine ALL earths to a single point. You will have to open up the unit, to see what colors are used for the 5 - DDC Return10 - GND-Sync/Self raster12 - DDC Data 13 - H-Sync 14 - V-Sync 15 - DDC Clock Settings they are marked on the motherboard.
Generally, this is caused by the loss of one of the main color inputs (Red Green Blue). Do the Following:
Check the cable connections at both the monitor and the computer. Look inside the connector for any bent bent pins (there may be some that appear to be missing, generally that is normal) then reset the connections firmly and tighten the retainer screw snug, but not extremely tight.
If that doesn't resolve, try the monitor on a different system and see if the problem follows the monitor. If it does, try a different cable. If the problem doesn't occur on another system, then the video card of the effected system is suspect.
If issue occurs on multiple systems with known good cables, then the monitor will need replacement.
Disconnect the monitor signal cable from PC and switch on your monitor. It should show some logo with Red, Green and Blue colors with a message similar to "No signal". If so, your monitor is working fine. Sometimes if the brightness and contrast is set to zero using controls present in the monitor, it will not show up anything. check wheather somebody set your monitor brightness and contrast to zero. If so incease them. As a last try connect to different PC and check before approaching a service center. I hope this will help you out. :)
The solution: hidden menu within the main menu itself. Hold the Menu button down while pressing Power to power on, and release power button only when the screen comes up, still holding the menu button. The menu will appear and there will now be a hidden selection, "Auto Color", printed in a red-on-black font at the bottom of the menu. Use the +/- buttons to access it, and press Menu. My green/yellow tint went away! Now my picture works great, and the setting lasts through Auto-Adjusts and Resets!
There are a few things that can cause this. The two most frequent:
(a) Has the monitor or computer been moved? The connector may be loose or slightly "off" of the port on the video card.
(b) If that's not the case, does it happen all the time? It's possible that one of the color 'guns' is off or malfunctioning - which means, essentially, a dead monitor. A 15" CRT just isn't worth fixing these days.
The little buttons beneath the monitor, unfortunately, do nothing for color adjustment - just brightness, contrast, and the usual positioning controls.
If your color is messed up on your display also then I think you need a new monitor. Why don't you try using a monitor that you know works and see if you have the same problem. Then let us know the results or the answer so we can have a little more to work with.
Picture Mode: Expert1
Fresh Contrast: Off
Noise Reduction: Medium
Black Level: Low
Real Cinema: On
Color Standard: HD (N/A w/HDMI)
White Balance: Warm
**Method: 10-Point IRE
Color Management System
Red Color: 0
Red Tint: 0
Green Color: 0
Green Tint: -15
Blue Color: 0
Blue Tint: 11
Yellow Color: 15
Yellow Tint: 2
Cyan Color: -15
Cyan Tint: 0
Magenta Color: 0
Magenta Tint: -1
lg70 nice tv excellent processor just to bad there is no intensity control on color management oh well still better than what the three s are pushing block out the hype lg will be number 1 in a few years haters are starting to come around and well leds coming,
p.s. i dont work for lg just tired of losers bashing stuff because they dont own it. im isf certified those settings are right on the money straighter than a ruler