An expert who has achieved level 2 by getting 100 points
An expert that got 10 achievements.
An expert that got 5 achievements.
An expert whose answer got voted for 100 times.
Re: Mitsubishi screen replacing
You must remove the front bezel and frame holder to replace the screen. You will usually see the screws holding the from from the rear of the unit. Once you get the frame off, take note of the way the old screen is installed. There is usually a label on one side near the bottom; the new screens must be installed with the label in the same location. The lenticular goes on the outside (facing the viewer) and the fresnel goes on the inside facing the mirror. You will be able to recognize the fresnel, it has a series of concentric circles that are raised on the sirface of the plastic Be sure to rate this solution.Thanks!
a 6ya Technician can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US. click here to Talk to a Technician (only for users in the US for now) and get all the help you need. Goodluck!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
there are 2 functionality screens and 1 screen protector (on some) front screen = lenticular back screen = fresnel very front screen = screen protector (you can replace w plexiglass)
the fresnel and lenticular are very specific.. contact your local repair center for a new one. you can cut them from old screens but have to do just right (fresnel is a lens type - pic will be distorted if off center)
maybe find a old junker tv to pull screens from because new ones are about $100 a piece
There is not much you can do besides replace the screen. Go to www.encompassparts.com There are 2 screens together on the front. The outside screen is the lenticular sceen and the inside screen is the fresnel screen. Thanks
First, which screen do you need -
The lenticular screen is dark in color is rough and has ridges.
There is a fresnel screen behind it.
IF you have a screen protector that is smooth, clear and see through, it would be the very first screen you can see and feel.
If your TV is the square shaped, 4:3 ratio TV, Mitsubishi has probably stopped production on replacement lenticular screens. HOWEVER, we have a couple of those screens still in stock.
After you take the frame off, lay it on a table or put a sheet down on the floor before you lay the frame down. You may need to take the frame apart to get the lenticular screen out.
we recently cracked our lenticular screen on our 73 in mitsubishi i called the manufacturer and they said they no longer make them. so i looked thru websites to see if i could find some one with a 73 in tv or bigger that they were no longer using or didnt work and i found a guy on www.ksl.com that had an 80 inch tv and we went to go pick up screen cut it to my tv size and it worked!!.
WD-57731 & WD-65731 Front Disassembly 57” & 65” Models Screen Frame Removal 1) Pull off the Speaker Grill. 2) Remove all the screws (b) from the upper rear cover (except one at an upper corner to support the frame). 3) Remove 10 screws (a) from the front of the screen frame. 4) Remove the remaining ***** (b) (supporting the frame). Carefully pull the Screen Frame from the TV and disconnect the ES and LE connectors. 57” & 65” Models Screens Removal from Frame 1) From the rear of the Screen Frame remove 20 screws (a) from the top and bottom rails 2) Remove 6 screws (b) from each side rail. 3) Carefully lift the Screen assembly from the Frame.
MODEL: WD-52631 / WD-57731 / WD-65731 Screen Replacement CAUTION: Wear gloves when handling the Lenticular Screen and Fresnel Lens. This prevents cuts and finger prints. Do not place Fresnel Lens in the sun. This may cause fire and heat related injuries. Lenticular Screen and Fresnel Lens Replacement 1) Apply LENS-TAPE along the rear top edge of the Lenticular Screen. 2) Place the Fresnel Lens on top of the Lenticular Screen, and apply pressure along the top edge. 3) Place the screens in the screen frame and reinstall the cushions, top, bottom and side rails. NOTE: The Lenticular Screen label must face the front and the Fresnel Lens label face the rear. 4) Reverse the Screen Removal Procedure and insert the screens in the Bezel. Lenticular Screen and Fresnel Lens Removal 1) Remove the top, bottom and side HOLDER-SCREEN rails and their cushions from the Screen Frame. 2) Lift the screens as a single unit from the frame. 2. Separate the Lenticular Screen and Fresnel Lens. Note: When separating the Lenticular Screen from the Fresnel Lens, use caution while prying the Screen and Lens apart. Use a slot type ***** driver, and remove the pressure sensitive double sided tape.