Question about Digital Cameras

1 Answer

It says Frame No. Full when i try to take a picture

Posted by on

  • Anonymous Feb 20, 2009

    sameproblem. it happened as I was taking px. I assumed that the memory disk was full since I was taking a ton of px. I thought it was full. stopped taking px. downloaded the px. put memory disk back in and it still said it. Then we deleted extra files off the memory disk and it still said frame no. full, then we deleted a few px off the actual camera and tried taking a px without the memory disk and it still said frame no. full

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 1 Answer

I just received this error too. This is what corrected it:
Go to --> Menu/Setup/Frame No.
Click "RENEW"


Posted on Jun 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Frame no. full


In the English Manual on page 150 it says Frame no. full:
The frame number has reached 999-9999. Remedy:
1 insert a formatted Memory Card into the camera. 2 Set RENEW as the FRAME NO. setting in the (SET) SET-UP menu (> p.117).
3 Start taking pictures (The frame number starts from "100-0001").

4 Set CONTINUOUS as the FRAME NO. setting in the (SET) SET-UP menu. Good luck

Jan 13, 2014 | Fuji FinePix S700 Digital Camera

1 Answer

I got new Sigma 18-200 DC II lens, with Canon EOS 5D Mark II it has black lens frame is visible through viewfinder or on the photo. Does it mean this lens is not compatible with 5DmrkII?


The EOS 50d Mark II is what's known as a "full-frame" camera. Its image sensor is the same size as a frame of 35mm film. The Sigma DC lens is intended for cameras with smaller sensors. The lens is compatible in that it will work with the camera to take pictures, but the pictures are cropped due to the smaller imaging area of the lens.

In order to use the full image sensor area you need to use full-frame lenses. In the case of Sigma, this means lenses without the DC designation.

Aug 03, 2012 | Digital Cameras

1 Answer

Won't let me take pics, says FRAME NO. FULL


Your Counter has reached 999.999
Here's what you do.
Make sure you have no pictures on your card to start with.
Place the card in the camera and turn it on.
Press "Menu" and go to the "Set" menu and select "Format". This will wipe your card completely clean. When this is done select "Frame No" in the set up menu and set it to "Renew".
Now come out of the menu options and take a picture.
When you review your picture the counter should read 100.001
Now go back to the set up menu and reselect "Frame no." and set to continuous ("Cont.")
Happy snapping

Oct 16, 2009 | Fuji Digital Cameras

1 Answer

What does Frame No Full mean?


If you look at the top right of your camera screen when reviewing pictures you should see the frame count. As yours is reading "Frame number full" the count should be reading 999.9999 so you need to reset to 100.0000. How to do this is posted in my tips section of my profile under "THE ONLY WAY I KNOW HOW" I have pasted the section below.
Cheers

FRAME NUMBER FULL!!

If you get this message on screen then your counter has reached 999-9999 and the camera will not take anymore pictures until you reset the counter to 100-0001.

To do this follow the instructions in your manual or read on my friends...

Firstly, make sure you have a picture card inserted into your camera and you have saved any pictures on it to your pc because you are about to format the card inside the camera and you will lose any pictures you have stored on there.

Ok. turn your camera on and press the menu/ok button and select "SETTINGS" from the menu.
Scroll through the menus until you find FORMAT. Select this and you will be asked if you would like to continue. Select OK.
Depending on how large your card is (16mb - 1,2 gb etc) will determine how long this will take but it's not very long.
After you have done this your card is now wiped clean of memory and has been formatted to be used for your cameras software.

Next, select FRAME in the SETTINGS menu and set your camera to RENEW and press OK.
Now come out of your menus and take a picture.

Review the picture taken and check the counter reading in the top right of the screen. It should now read 100-0001. The counter has now been reset.

Now go back into your menu and select SETTINGS again and scroll down to FRAME once again. Set this back to CONT (continuous) and press ok. Your camera should be reset and you can now use it.

Note: If you have more than one card you will have to reformat each card because the camera will store and recognise the frame numbers stored on the card and continue using them rather than set them to 100-0001 or will open a new folder on your card and start using this as the new one thus taking up more space on your card reducing the number of shots you can store on it

Sep 30, 2009 | Fuji FinePix F40fd Digital Camera

1 Answer

Come up with frame number full


The problem is ther internal memory is full or your external card is full and you have to reformat the card. Then you should be able to use the camera .

Apr 10, 2009 | Digital Cameras

1 Answer

!Frame No. Full and cannot take pictures


Well i was just having the same problem and decided to search for an answer. It looks like you might want to reset your camera. Go to menu, set up then click on three and you should find "reset" click that and in no time you will be able to take pictures again!

Mar 21, 2009 | Digital Cameras

1 Answer

Fuji frame no full


I had the same problem. Here's what I think is going on: the camera has a finite set of numbers that it can assign to pictures. If it is set to "continuous," then every picture that you take gets assigned a new number (even after you delete them off the card). To fix this, you need to set it to "renew" the picture numbers. Here's how to do this: Menu --> Setup --> Frame No. --> Renew.

Hope that helps!

Dec 14, 2008 | Fuji FinePix V10 Digital Camera

1 Answer

"Frame NO. Full"


Try going in to the "setup" menu and change the frame numbering from "continuous" to "renew", if it is not already done. Sounds like you are on the continuous setting which keeps adding numbers, even though you've erased many. Going to renew starts the numbering over so it keeps reusing previous numbers.

Jul 06, 2008 | Fuji FinePix Z100fd Digital Camera

1 Answer

Camera says Frame no full cant take anymore pictures Help!


Copy your card to hard drive, reformat your memory card, and see what the numbers of pictures it gives you.

If you lower the resolution of the camera, the more pictures you can take.

Jun 16, 2008 | Fuji FinePix F480 Digital Camera

2 Answers

Frame number full


when i turn on the camera I get a frame no. full, I tried formating the memory card to no avail. I can't take a picture with this error

Jun 16, 2008 | Digital Cameras

Not finding what you are looking for?
Digital Cameras Logo

Related Topics:

349 people viewed this question

Ask a Question

Usually answered in minutes!

Top Digital Cameras Experts

kakima

Level 3 Expert

96738 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Steve

Level 3 Expert

3287 Answers

Are you a Digital Camera Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...