Question about 3Com SuperStack 3 NBX V5000 Call Processor Voice Mail Server

1 Answer

Can't get into the NBX NetSet utility of 3COM SuperStack 3 NBX 3C10202

I followed steps in the NBX Installation Guide by Changing the default IP settings of my computer. After that I tried to access the NBX NetSet utility, enter the following address into the browser’s address field:192.168.1.190 but still couldn't get any luck. When I look IP in hyper terminal is 192.0.0.1 so I believe that if I change the IP, It would actually work. But I don't know how. So, is anyone knows how to change IP to default setting or any way that I can get into NetSet utility?

Here's what I did:
1. Connect directly from PC to NBX using category 5 Ethernet crossover cable
2. changed the IP settings of your computer to:
IP address: 192.168.1.191
Default gateway: 0.0.0.0
Subnet mask: 255.255.255.0
3. Start a IE browser and tried to access the NBX NetSet utility, enter the address 192.168.1.190 but didn't work.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 144 Answers

Try 192.162.1.254

Posted on Nov 10, 2008

  •  Luis Moreira
    Luis Moreira Nov 13, 2008

    Hi again,

    Try this: reset the equipment and 192.168.0.101

      Default Password is 0000 or 00000000.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to find my ip address on windows 7


You can find your IP address on windows 7,by following the below steps:
1.Start->Run->cmd prompt
2.In that,just type ipconfig and then click enter
For example: It will show ip address like 74.110.208.65
If you want to find your network ip address that is provided by your ISP,visit Ip-details.com .

Mar 30, 2013 | Black Box IP Address Translator With...

Tip

How do I reset LinkSys Router Default Password?


When you forget your Linksys router password, you will need to reset it back to the factory defaults. You can restore the router configuration to back to the factory by following the steps outlined below:

1. Hold in the reset button of the router for 30 seconds. 2. Unplug your power cord for 30 seconds 3. Plug back your power cord4. Wait for a few seconds then release the reset button.
NOTE:¨ When holding in the reset button, make sure that you do not release it until you are sure that it has been compressed for at least 30 seconds or more.

¨ This procedure resets the router back to all its factory default settings thus apart from affecting your username and password, it will also affect your configuration and IP addressing.

Once this is complete, you can now login and reconfigure your password. To do this:

1. Connect a PC to one of the Linksys router Ethernet ports

2. Open your web browser and go to the URL http://192.168.1.1. This will take you to a web page with a popup box which asks you to enter a username and password to login required to login to your router

3. On older LinkSys routers, the username is set to blank and the password is set to "admin" (without the quotes). On newer Linksys routers, both the default username and the default password are set to "admin".

4. Click on login. You have logged in to the Administrator account and are now able to access and change a number of configuration options for your router.

5. Click on management tab then change your administrator password to any password that you like. Remember to choose a strong password that others cannot guess but that will be easy enough for you to remember.

6. You can also choose to reconfigure other aspects of you Linksys router at this point.

on Nov 25, 2010 | Other Network Devices

1 Answer

Bought 3c0m nbx100 off ebay and do not have the password. Version is R5.4 I logged into to com port but unable to find the password.


Default Password is 0000 or 00000000 or Reboot into previous version and change password to an alphanumeric password The word "administrator" has to be entered as the User Name. this pdf could help (http://support.3com.com/infodeli/tools/nbx/50/docs/admin_nbx50.pdf) and this pdf will tell you how to update the machine to a newer version or if it is in the newest version you must downgrade it just folow the instructions on this pdf (http://support.3com.com/infodeli/tools/nbx/60/upgr_nbx60.pdf) or you could try and Connect a PC to the console port of the NBX (9600 baud, 8 data bits, 1 stop bit, no parity)1. All commands are case sensitive. At the NBX or SS3 Prompt type nbxDb. NBXs response- DBITEST (? for help):
2. At the DBITEST prompt type X.NBXs response-encrypted admin pass ---> (!Ofm0uealStEsrx1) 3. Contact 3Com Tech Support to have the password decrypted. if you have anymore problems i would be happy to help and if you cant fix it still i would be happy to do it for you for a small fee ..i hope this helped and i look forward to hearing from you

Jan 15, 2011 | 3Com NBX 100 (3c10110d) Control Processor

1 Answer

The dsl modem the i have did not come with an access code .. how do i find it


Hi,

This Utility program from HP will help you locate few details on your network

This Utility program will help you locate few details of your network like,

1. SSID ( network name )
2. WEP/WPA Key ( Your network security key )
3. The PC/Laptop IP Address
4. Router IP address
5. Which all Devices are connected to your Router/Network Wireless
6. Which all Network are available nearby your place
7. Let you access the Router Configuration

Click here to Download the HP Network Diagnostic Utility

Download the file on Desktop and Run the program ( Ex. File name = HPNDU.EXE )

Follow the Instructions on the Screen and do accordingly.

Nov 06, 2010 | Arris Netopia 2210 ADSL2+ Modem SinglePort...

1 Answer

How to reset TrippLite SMNPWEBCARD


I bought a used power outlet control unit(PDUMH30NET).I could not find any instructions how to reset to factory defaults to clear out any static IP address and go to DHCP, so I pulled out the card, saw a small pushbutton between the 2 round connectors. I think the following process did the reset but its IP wasn't showing up at the router so I tried a couple of combinations before I found the IP with a PING scan.
Take off the small plate holding the card in(2 screws)
With a toothpick reach between the round connectors and press and hold the small button for close to a minute. I also tried
pressing it and holding it while inserting the card. The card takes several minutes to restart so wait for the green Status light. If you can't see it's MAC and IP address at the router, paste this in a Command window and run it:

FOR /L %i IN (1,1,254) DO ping -n 1 192.168.0.%i ' FIND /i "Reply">>
c:\ipaddresses.txt

Look in the file for an IP that wasn't on your network before- that should be it.Put it in the browser and you should get the login. admin/admin got me in.

Sep 10, 2010 | Tripp Lite (SNMPWEBCARD) Remote Management...

1 Answer

Ip address changed, and canot figure how to change in linksys set up


Hi,
restore the linksys to default setting by using a little switch on the back of router between ethernet port and anteena. press that button using any thin screw driver and power on that after keep pressing for 1-2 mins only. it will restore your router to default setting. now its default ip will be 192.168.1.1 and default username & password will be admin.you can now open it in web browser and configure it.

Aug 21, 2009 | Other Network Devices

1 Answer

Guidance setting up a shared connection :)


1- set up router trough desktop
2-run program for wireless, after it gives you the IP ( which it already has, set user name and password for protection)
3-set up the laptop as a "Shared folder" along with the printer if there is one.

Aug 24, 2008 | Other Network Devices

1 Answer

Can't portforward


Identifying Your Router's IP Address
You should have now received an IP address from your router. To view your IP address information do these two steps:
  1. Start > Run then type CMD then press Enter.
  2. Then in the command prompt type ipconfig /all
If you see your network interface with a list of IP addresses(should not be all 0.0.0.0's or 169.* addresses). If you got an IPstarting with 192.168.* or 10.* you are doing great! If not, verifyconnections or reboot computer. Observe the Gateway IP Address. This is the router's IP address. It may be one of the following, test in your Web browser:
http://192.168.1.1 or http://192.168.0.1 or http://192.168.0.50 or http://10.0.0.1

Once you see a login prompt, you need to log in with the default routerlogin. Usually they are a combination of "admin" and no password or"admin" for the password and no username " or "admin" for username and"password" for the password. Alernatively, you can search Google withyour model number and it should yield you some useful information onyour router including the default login/password.

Then when you are inside it, you should go to the LAN section andenable DHCP (if it already isn't). For security you may limit theamount of addresses to the number of computers (you don't have 254computers, so why allow 254 computers addresses?). For example, I allow3 IP addresses on my network to be issued, since I have a NAS, Laptopand a Desktop.

Jul 23, 2008 | Lucent DSLPipe Bridge/Router

1 Answer

Internet sharing


Hi, Could be done. On the Dell XP - 1. Activate your Internet Connection Sharing. Go to Control Panel, Click on Network Connections, right click on your Local Area Connection, Properties, Advanced tab, check Allow other network users to connect through this computer's internet connection. In Home networking connection, choose "Local Area Connection", OK; 2. Back to General settings, click on Internet Protocol (TCP/IP), click on Properties, tick Use the following IP address: IP address 192.168.0.1, Subnet mask 255.255.255.0, Default gateway 192.168.0.1, if you know ITT DNS use them otherwise tick "Obtain DNS server address automatically." You have to connect the DellXP with the DellVista using a crossover networking cable. On the Dell Vista- 1. In your Network Connections, right click on your Local Area Connection, Properties, click on Internet Protocol (TCP/IP), click on Properties, tick Use the following IP address: IP address 192.168.0.2, Subnet mask 255.255.255.0, Default gateway 192.168.0.1, if you know ITT DNS use them otherwise tick "Obtain DNS server address automatically." The above method will also work with peer to peer wireless networking. It might also facilitate connection if you enable auto-detect proxy settings in your browser. There are other methods. This is also better explained at Microsoft support Hope this be of help/idea. Post back how things turns up or should you need additional information. Good luck and kind regards.

Sep 30, 2007 | Other Network Devices

Not finding what you are looking for?
3Com SuperStack 3 NBX V5000 Call Processor Voice Mail Server Logo

Related Topics:

1,447 people viewed this question

Ask a Question

Usually answered in minutes!

Top 3Com Other Network Devices Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18298 Answers

Coss

Level 3 Expert

1043 Answers

Tony

Level 3 Expert

2598 Answers

Are you a 3Com Other Network Device Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...