Question about Whirlpool Calypso GVW9959K Top Load Washer

Open Question

Error code i have crosley front loader and i notice e70 code pops up on screen any solutions as to what that is and how to solve it

Posted by on

6 Suggested Answers

eagle338
  • 4889 Answers

SOURCE: E70 Error Code

Means you are not getting cold water into unit..Either cold water hose is connected to the wrong hose or cold water faucet is not turned on..You can solve this by connecting hose to cold water faucet and cold water inlet on washer..

Posted on Nov 06, 2007

Master_Tech
  • 770 Answers

SOURCE: Crosley Front Load Washers FL Error

Flood Condition F L “FL” flashes if any overfill condition occurs. This condition occurs when excessive water in
the tub causes the overfill switch to trip. The control must realize that the trip was due to an
overfill condition instead of a suds lock condition in order for “FL” to be displayed.
With an overfill condition, the beeper repeats a warning every 10 seconds with no time out.
The pump is cycled in drain mode for 30 seconds on, 30 seconds off until the overfill switch
resets or power is discontinued to the unit.
Press STOP/CANCEL to clear the display.

Posted on Feb 18, 2008

aborcass
  • 2651 Answers

SOURCE: E70 error on Model LTF2940FE1 Front loading washer

good to see you cked that , 1 question though are you by chance using stainless hoses made by company FLOODSAFE. if so theres your problem theres a shut off inside the hose itself that is malfunfuctioning, replace with regular s/s hose and all will be good. if your not usinf a floodsafe hose hten lets go to the next hting- when oyu first start machine, cold water flows in before cycle even starts, can you hear it coming in??? at least trying perhaps a light humm with no water? water vavle is located under main top you can remove the top and check for voltage when trying to fill

Posted on Mar 10, 2008

GodBlessU
  • 3513 Answers

SOURCE: Samsung J845 front loader washing machine. Error

Hi
An OE error presents if the washing machine has not successfully drained the water in ten minutes.
there are a few simple steps to take before calling for service.
Step 1: Check the drain pump filter.
Items caught in the drain filter will prevent proper drainage. Over time build up can occur from detergents and additives used in the machine. Manually drain unit through the drain hose, then lay a towel down to catch the water, and remove the filter. Clean the filter thoroughly and restart the machine.

Step 2: Check the washers drain hose.
If the drain hose is not installed properly, the washer will not drain properly. The drain hose should not be installed more than 1 meter higher than the bottom of the washing machine.

Step 3: Confirm that the washer is leveled properly.
If the unit is not leveled properly, it will not drain properly. The front of the unit cannot be higher than the back or vice versa. If not properly leveled, the water can flow back into the machine. If this is the cause of the problem, please level the machine using the supplied leveling wrench. When you place a level on the washing machine, the bubble should be in the center. Confrim that the washer is leveled from side to side and front to back.
you can perform a diagonal test when leveling the washing machine to ensure that the unit does not tilt from corner to corner.

Thanks for contacting fixya.com

Posted on Sep 30, 2009

  • 1 Answer

SOURCE: error code E70 on my Frigidaire front loading

The hot and cold water hoses were connected wrong to the washer.

Posted on Dec 23, 2009

  • 177 Answers

SOURCE: miele front loader washing machine W3275- error co...

hi,

this is a tachogenerator fault or the drive motor brushes are faulty. you will need a Miele service tech or a Miele service agent to look at this.

Posted on May 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

AEG Lavamat 76810 E70 7Beeps Does seem to still work but display shows E70 and 7beeps over and over. Many thanks gary


I Have AEG Lavamat 76810 E70 7 Beeps and Beeps never stops

The water was not hot
I took all the multi-plugs out and put them back in the whole machine ALL CONNECTORS
Now it works fine E70 is gone

Jul 14, 2011 | AEG Lavamat 16810 Front Load Washer/Dryer

1 Answer

It is stopping in the cycle and reading E70 on the screen.


Hi,

The main cause for this e70 error is that the hoses would have swapped (hot to cold, cold to hot). It means the washer isn't getting cold water.Try to switch between the hoses. Another possibility is the faucets are not turned on.
Hope this solution will fix your problem for sure.


Thank You !!

Jul 16, 2010 | Frigidaire GLTF2940ES Front Load Washer

1 Answer

E70 error code


The main cause for this e70 error is that the hoses would have swapped (hot to cold, cold to hot). It means the washer isn't getting cold water.Try to switch between the hoses. Another possibility is the faucets are not turned on.... Hope this solution will fix your problem for sure.

Mar 30, 2010 | Frigidaire Affinity ATF7000E Front Load...

4 Answers

Washer wont drain and spin properly


whee is th drain filter on crosley front loader

Apr 02, 2009 | Crosley CW5000 Front Load Washer

2 Answers

I have a fridgdaire front loading washing machine and the code e70 keeps coming up and the whole system will shut down what does this mean???


Hello,

You are going to need to download the Factory Service Manual for your Washer. This is a General Code, not specific to anything, You need to run the machine through it's diagnostics to determine the service code that is stored.

Once you get the service code you can narrow down and identify the issue.

Here is the Repair Manual Download Link

Thanks

Jan 06, 2009 | Frigidaire ATF6000ES Front Load Washer

1 Answer

Error Code E70


water fill problem ,,,check fill hose for kink,,,or lost of water pressure,,,you may need to clean inlet vavle screens..onthejob

Dec 20, 2008 | Frigidaire Affinity ATF7000E Front Load...

1 Answer

Error messages


what are other codes? i believe this could be a cold water issue. check your screens at the fill hoses

Sep 22, 2008 | Frigidaire GLTF2940E Gallery 3.5 Cu. Ft....

2 Answers

Crosley Front Load Washing Machine


FL is a flood condition fault, too much water in unit. i would turn off water supply and try to spin water out. select spin button, should put 8 min on timer try startin that water should pump out then if not you got somethin stuck in pump (lint likely)

Feb 22, 2008 | Whirlpool Calypso GVW9959K Top Load Washer

9 Answers

E70 error code repeatedly comes up when attempting to start a load and you have to cancel and restart 4-6 times before the load washes; again at the end of a load it will come up with the E70 error and to...


Means you are not getting cold water into unit..Either cold water hose is connected to the wrong hose or cold water faucet is not turned on..You can solve this by connecting hose to cold water faucet and cold water inlet on washer..

Nov 06, 2007 | Frigidaire GLTF2940ES Front Load Washer

Not finding what you are looking for?
Whirlpool Calypso GVW9959K Top Load Washer Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...