Question about Dishwashers

1 Answer

Outlet hose disconnected and no replacement availble from local services

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 324 Answers

Whats the model# an make?

Posted on Nov 07, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change a heater core on a 2008 pontiac torrent


Your best bet would be to take your vehicle to a qualified repair shop ! You'll have to Recover the refrigerant from A/C , drain the coolant .
Remove the evaporator outlet hose and liquid line nut from the thermal expansion valve (TXV).
Remove the evaporator outlet hose from the TXV.
Remove and discard the sealing washer from the evaporator outlet hose. Refer to Sealing Washer Replacement .
Remove the evaporator outlet hose and liquid line from the TXV.
Remove and discard the sealing washer from the liquid line. Refer to Sealing Washer Replacement .
Install a protective caps to the evaporator outlet hose and the liquid line to prevent contamination and desiccant saturation.

Reposition the heater outlet hose clamp at the heater core.
Remove the heater outlet hose from the heater core (1).
Reposition the heater inlet hose clamp at the heater core (2).
Remove the heater inlet hose at the heater core.
Plug the heater core and the evaporator core with clean towels to prevent spillage when the HVAC module is removed.

Remove the HVAC module seal nuts from the front of dash.
Remove the instrument panel (I/P) retainer. Refer to Instrument Panel Retainer Replacement .
Remove the shift control bracket. Refer to Transmission Control Replacement .

Remove the center floor air outlet duct by sliding the duct forward then up at the rear.
Remove the center I/P air outlet duct retainers from the instrument panel tie bar.
Remove the center I/P air outlet duct from the instrument panel tie bar.
Remove the instrument panel tie bar. Refer to Instrument Panel Tie Bar Replacement .
Disconnect the blower motor electrical connector from the I/P wire harness.
Disconnect the blower motor control module electrical connector from the I/P wire harness.
Disconnect the HVAC module electrical connector from the I/P wire harness.
Remove the HVAC module from the vehicle.

If you haven't done this before ,forget it !

Aug 14, 2016 | Pontiac Cars & Trucks

1 Answer

Thermostat on 2005 aviator location


Removal & Installation

Print


4.6L & 5.4L SOHC Engines

  1. Partially drain the engine cooling system to a level below the thermostat.
  2. Disconnect the upper radiator hose from the water outlet adapter.
  3. Remove the power steering reservoir upper mounting bracket.
  4. Remove the bolts and remove the water outlet adapter.
  5. Remove the water thermostat and the O-ring seal. Discard the O-ring seal.
  6. Installation is the reverse of the removal procedure. Tighten the water outlet adapter bolts to 18 ft. lbs. (25 Nm). Tighten the power steering reservoir upper mounting bracket as shown in the accompanying illustration.

    0996b43f80204ea2.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. View of the power steering reservoir upper mounting bracket and tightening specifications


    0996b43f80204ea3.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Exploded view of the water outlet adapter and tightening specifications



5.4L & 6.8L Engines

  1. Partially drain the cooling system to a level below the thermostat.
  2. Disconnect the upper radiator hose.
  3. Remove the coolant outlet connection, as follows:
    1. Remove the bolts.
    2. Remove the coolant outlet connection.

  4. Remove the (A) coolant thermostat and the (B) O-ring seal.
  5. Discard the (B) O-ring seal.

    0996b43f80204ef0.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Remove the (A) coolant thermostat and the (B) O-ring seal


To install:

NOTE Thermostat must be installed as illustrated.
  1. Use a new (A) O-ring seal to position the (B) coolant thermostat in the (C) upper intake manifold.

    0996b43f80204ef1.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Use a new (A) O-ring seal to position the (B) coolant thermostat in the (C) upper intake manifold

  2. Install the coolant outlet connection, as follows:
    1. Position the coolant outlet connection on the upper intake manifold.
    2. Install the bolts and tighten to 15-22 ft. lbs. (20-30 Nm).

  3. Connect the upper radiator hose.
  4. Fill the cooling system.

  1. Before servicing the vehicle, refer to the precautions section.
  2. Partially drain the cooling system to a level below the thermostat.
  3. Disconnect the upper radiator hose.
  4. Remove the coolant outlet connection, as follows:
    1. Remove the bolts.
    2. Remove the coolant outlet connection.

  5. Remove the (A) coolant thermostat and the (B) O-ring seal.
  6. Discard the (B) O-ring seal.

    0996b43f80204ef0.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Remove the (A) coolant thermostat and the (B) O-ring seal


To install:

NOTE Thermostat must be installed as illustrated.
  1. Use a new (A) O-ring seal to position the (B) coolant thermostat in the (C) upper intake manifold.

    0996b43f80204ef1.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Use a new (A) O-ring seal to position the (B) coolant thermostat in the (C) upper intake manifold

  2. Install the coolant outlet connection, as follows:
    1. Position the coolant outlet connection on the upper intake manifold.
    2. Install the bolts and tighten to 15-22 ft. lbs. (20-30 Nm).

  3. Connect the upper radiator hose.
  4. Fill the cooling system.


5.4L DOHC Engine

  1. Partially drain the engine cooling system to a level below the thermostat.
  2. Disconnect the upper radiator hose, the heater water inlet hose and the heated PCV inlet hose from the water outlet adapter.

    0996b43f80204ea5.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Disconnect the upper radiator hose, the heater water inlet hose and the heated PCV inlet hose from the water outlet adapter

  3. Remove the water hose connection and thermostat.
  4. Installation is the reverse of the removal procedure. Tighten the mounting bolt to 18 ft. lbs. (25 Nm).

    0996b43f80204ea4.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Exploded view of the thermostat-5.4L DOHC engine

Aug 13, 2012 | 2004 Lincoln Aviator

1 Answer

Meile dishwasher G641 inlet /outlet hose has split can I ,buy a replacement hose


Hi jmjohnnamarti,

Yes you can, the part numbers below:

Drain hose (1.5M) = 2244182
Drain Hose (2.25M) = 2244212
Inlet Hose (Normal) = 5936070
Inlet Hose (Waterproof System - 2M) = 7638500

Get it from your local appliance spares outlet, might need to be ordered (Quite expensive)

Hope this helps :-)

* If you found this solution helpful, please rate it

Jul 18, 2011 | Dishwashers

1 Answer

Does not seem to drain completely - ran very long today and the last code I saw was "nd" - not draining? or not done?


nd code indicates a problem with draining. The problem could be:
1. Clog in the drain hose - 2. Drain pump in the washer needs replacement 3. Clog in your sewage
Some simple things to try out
a. Run a wet/dry shop vac at the end of the drain hose to clear out any crud/cloth debris. b. Replace the drain hose altogether (will require a bit of work). Remove the back panel (small) that holds the drain hose in place and disconnect the clamp that connects to the drain hose to thepump outlet. The whole drain hose can be purchased for under $20 at your local hardware store...
Good Luck!

Jun 11, 2011 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

Heater fan blows good but only blows cold air. Is it the heater core? The thermostat? How hard are they to replace if i do it myself?


Check the heater core by checking the hotness or coldness of the 2 tubes at the firewall that lead to the heater core.

If both tubes are hot, the heater core is fine. If both tubes are cold, then the heater core is plugged up and will have to be flushed out or replaced.

The thermostat, if stuck open, will delay the heating up of the heater core. It's not hard to replace the thermostat.

Thermostat Removal & Installation 4.2L Engine To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:
    • Some of the coolant
    • The upper radiator hose f150_42_thermostat.gif

    • The bolts (A).
    • The water outlet connection (B)
    • The water thermostat and paper gasket assembly (C)
To Install:
NOTE: The water thermostat is indexed and must be installed correctly.
  1. Install or connect the following:
    • The water thermostat
    • The thermostat
    • The water outlet adapter
    • The bolts
      1. Torque to: 80 inch-lbs (9 Nm)
    • The upper radiator hose
    • The coolant
4.6L/5.4L Engines To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:
    • Some of the coolant
    • The upper radiator hose f150_46-54_thermostat.gif

    • The bolts (A)
    • The water outlet connection (B)
    • The water thermostat
    • The O-ring (discard)
To Install:
  1. Install or connect the following:
    • A new O-ring to position the water thermostat in the upper intake manifold
    • The water outlet connection onto the upper intake manifold
    • The bolts
      1. Torque to: 18 ft-lbs (25 Nm)
    • The upper radiator hose
    • The coolant
prev.gif next.gif

Jan 28, 2011 | 1997 Ford F150 Regular Cab

1 Answer

I need to replace a thermostat in a 2000 Chevy 2500 6.0 liter pickup


4.8L, 5.3L and 6.0L Engines To Remove:
CAUTION
The thermostat is not serviceable separately. The thermostat housing (water pump inlet) and thermostat must be replaced as an assembly.
  1. Remove the radiator outlet hose. chevy_aval15_02-04_inlet.gif

  2. Remove the bolts from water pump inlet.
  3. Remove the water pump inlet from the water pump.
To Install:
  1. Install the water pump inlet to the water pump.
  2. Install the water pump inlet bolts.
    • Torque to: 11 ft-lbs. (15 Nm)
  3. Install the radiator outlet hose.
6.6L Engine To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Drain the engine coolant.
  3. Remove or disconnect the following:
    • Water outlet 6.6L Thermostat housing removal gm_trk_sil25_02-04_66_therm_hous_rem.gif

    • Bolt for the fuel line bracket
    • Thermostat housing cover bolts
    • Thermostats and seals
To Install:
6.6L Thermostats and seals gm_trk_sil25_02-04_66_therm_seal.gif

  1. Install or connect the following:
    • Thermostats and seals to the thermostat housing NOTE: The rear thermostat (D) has 2 vent valves. Install with the vent valves towards the rear of engine.
    • Thermostat housing cover with a NEW gasket
    • Thermostat housing cover bolts and tighten the bolts
      1. Torque to: 15 ft. lbs. (21 Nm)
    • Fuel line bracket bolt and tighten the bolt
      1. Torque to: 15 ft. lbs. (21 Nm)
    • Water outlet
  2. Fill the engine with coolant.
  3. Test drive the vehicle to confirm the repairs.
8.1L Engine To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    • Inlet hose from the water outlet Water outlet and thermostat removal chevy_sub25_02-04_60_thermost_rem.gif

    • Water outlet bolts (B)
    • Water outlet (A)
    • Thermostat (C)
To Install:
  1. Install or connect the following:
    • Thermostat
    • Water outlet
    • Water outlet bolts and tighten the bolts.
      1. Torque to: 22 ft-lbs (30 Nm)
    • Inlet hose to the water outlet
  2. Fill the cooling system.
  3. Test drive the vehicle to confirm the repairs.
prev.gif next.gif

Jan 12, 2011 | 2000 Chevrolet 2500

1 Answer

Where is the water pump gasket or the thermostat gasket in a 2002 cadillac escalade?


Thermostat Removal & Installation 4.8L, 5.3L and 6.0L Engines To Remove:
CAUTION
The thermostat is not serviceable separately. The thermostat housing (water pump inlet) and thermostat must be replaced as an assembly.
  1. Remove the radiator outlet hose. chevy_aval15_02-04_inlet.gif

  2. Remove the bolts from water pump inlet.
  3. Remove the water pump inlet from the water pump.
To Install:
  1. Install the water pump inlet to the water pump.
  2. Install the water pump inlet bolts. Torque to: 11 ft-lbs. (15 Nm)
  3. Install the radiator outlet hose.
8.1L Engines To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    • Inlet hose from the water outlet Water outlet and thermostat removal chevy_sub25_02-04_60_thermost_rem.gif

    • Water outlet bolts (B)
    • Water outlet (A)
    • Thermostat (C)
To Install:
  1. Install or connect the following:
    • Thermostat
    • Water outlet
    • Water outlet bolts and tighten the bolts, Torque to: 22 ft-lbs (30 Nm)
    • Inlet hose to the water outlet
  2. Fill the cooling system.
  3. Test drive the vehicle to confirm the repairs.
prev.gif next.gif

Nov 09, 2010 | Cadillac Escalade Cars & Trucks

1 Answer

Replace thermastat where is it and i need a easy fix solution


2.0L & 2.4L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Disconnect battery negative cable from remote negative terminal on shock tower and properly isolate to prevent accidental reconnection.
    CAUTION This operation must only be performed on a cold engine.
  3. Drain cooling system to the thermostat level or below.
  4. Remove or disconnect the following:
    Coolant recovery system hose Thermostat/engine outlet connector bolts Inlet hose and coolant elbow from thermostat housing
  5. Remove thermostat assembly and clean sealing surfaces.

    240b2a6.jpg
    Fig. Thermostat and housing-2.0L and 2.4L engines

To install:
  1. Place the new thermostat assembly into the engine outlet connector. Align air bleed with notch on the cylinder head.
  2. Install engine outlet connector onto cylinder head and tighten bolts to 110 inch lbs. (12.5 Nm)
  3. Connect the coolant recovery system hose.
  4. Fill cooling system.

  1. Drain cooling system to the thermostat level or below.
  2. Remove the Coolant Recovery System (CRS) hose and thermostat/engine outlet connector bolts.
  3. Remove the thermostat assembly, and clean sealing surfaces.

    969cc63.jpg
    Fig. Thermostat assembly-2.0L engine


    f7f1b3d.jpg
    Fig. Thermostat assembly-2.4L engine

To install:
  1. Place the new thermostat assembly into the engine outlet connector.
    1. Align air vent upward with notch on the cylinder head (2.0L engine).
    2. Make sure spring side of thermostat faces cylinder head.

  2. Install the engine outlet connector onto cylinder head and tighten bolts to 110 inch lbs. (12.5 Nm)
  3. Connect the Coolant Recovery System (CRS) hose.
  4. Fill cooling system.

2.4L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system to the thermostat level or below.
  3. Remove the Coolant Recovery System (CRS) hose and thermostat/engine outlet connector bolts.
  4. Remove the thermostat assembly, and clean sealing surfaces.

    a1e1b65.jpg
    Fig. Thermostat assembly-2.4L engine

To install:
  1. Place the new thermostat assembly into the engine outlet connector.
  2. Make sure the spring side of the thermostat faces the cylinder head.
  3. Install the engine outlet connector onto cylinder head and tighten bolts to 110 inch lbs. (12.5 Nm)
  4. Connect the CRS hose.
  5. Fill the cooling system to the proper level.

Hope help with this (remember rated this post).

Apr 15, 2010 | 2002 Chrysler Sebring

1 Answer

How do you change a fuel pump on a 1995 camry?


1992-96 Models
See Figure 6
Be sure this procedure is done in a well ventilated area.
  1. Disconnect the negative battery cable.
  2. Relieve the fuel pressure.
  3. Remove the rear seat cushion.
  4. Remove the floor service hole cover.
  5. Disconnect the electrical fuel pump wiring at the fuel pump assembly. Check for any fuel leakage while in there.
fuel pump and sending unit cover
  1. Remove the gas cap, this will prevent any fuel gas spilling out of any high pressure lines.
  2. Using SST 09631-22020 or an equivalent line (flare nut) wrench, disconnect the outlet

pipe from the pump bracket.
  1. Remove the pump bracket attaching screws.
  2. Disconnect the return hoses from the pump bracket, then pull out the pump/bracket assembly.
  3. Remove the nut and spring washer, then disconnect the wires from the pump bracket.
  4. Remove the sending unit attaching screws, then remove the unit from the bracket.
  5. Pull the lower side of the fuel pump from the bracket.
  6. Unplug the connector to the fuel pump.
  7. Disconnect the hose from the pump.
  8. Separate the filter from the pump. Use a small screwdriver to remove the attaching clip.
  9. Inspect all of the lines, hoses and fittings for any sign of corrosion, wear or damage to the surfaces. Check the pump outlet hose and the filter for restrictions.
  10. When reassembling, ALWAYS replace the sealing gaskets with new ones. Also replace any rubber parts showing any sign of deterioration.

To install:
  1. Install the pump filter using a new clip. Install the rubber cushion under the filter.
  2. Connect the outlet hose to the pump, then attach the pump to the bracket and tighten to 22-25 ft. lbs. (29-34 Nm).
  3. Engage the connector to the fuel pump.
  4. Install the fuel sending unit to the pump bracket.
  5. Install the fuel pump and bracket assembly onto the tank. Use new gaskets. Tighten the pump bracket retaining screws to 34 inch lbs. (4 Nm).
  6. Connect the return hoses to the pump bracket.
  7. Install the service hole cover, then the engage the fuel pump and sending unit connector.
  8. Install the rear seat cushion.
  9. Start the engine and check carefully for any sign of leakage around the tank and lines. Road test the vehicle for proper operation.

Mar 03, 2010 | 1995 Toyota Camry

2 Answers

NuTone Central vac won't turn off


If the central vacuum tank will not turn OFF even with the switch in the “OFF” position, then the low-voltage wires should be disconnected from the tank. If the tank continues to run and still will not turn off, then most likely the relay inside is defective (but it could be a defective and/or shorted ON/OFF switch). If with the low-voltage wires disconnected the tank is able to then be turned off with the switch, then there is a short in the low-voltage wires or a hose is plugged into an inlet somewhere. ~ TTURAMBAR

Mar 11, 2009 | Broan-NuTone VX475 Bagged Central System...

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Brad Brown

Level 3 Expert

13765 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...