Question about Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Code 5d My washer gives a code of 5d just after washing a load and when it is about to go into the drain cycle. Do this mean that the pump is bad?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 63 Answers

Its a water senser error code check for loose wire bottom front of outer tub ,i have never had a bad one "less soap plz"

Posted on Nov 15, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Getting nd code and load will not drain water after washing and will not go into spin mode. I replaced the drain pump (one vane on pump broke) but still getting the code. I checked and cleaned all hoses...


"nd" means: Your washer is not draining. It can also mean that the unit senses a small clog while draining. Before calling for service, check the following.

1) Turn off the unit and turn it on again.
2) Select only the Spin Cycle.
3) Press the Start/Pause to drain the water.
If it still does not drain, call for service.

So it sounds like it knows its not draining but wants to. If you can hear the pump driving, it is a clog somewhere. If you don't hear the pump driving, it could be the pump has died.

For all you do-it-yourselfers out there, I got this information from the user manual I found at:

http://downloadcenter.samsung.com/content/UM/200710/20071010083409359_WF337A-02440A-06%5B1%5D.pdf

Mar 24, 2015 | Samsung WF337AA Front Load Washer

1 Answer

Long spin cycle of my Samsung WF8590NHM Front Load Washer is always interrupted and throws this flashing "5d" error code.


Hi.

The error code is not 5D but SD, which means slow drain detected.

Check drain hose. Check drain filter attached to the pump. Check pump itself and pressure switch.

Regards.

Ginko

Aug 20, 2011 | Samsung WF306BHW High Efficiency Front...

2 Answers

My washer is constantly showing 5d. What does that mean?


Hi


Thanks for using FixYa. Error 5d means too much detergent was used. Try the following procedure---

Run the unit through a RINSE/SPIN cycle.
Run a NORMAL cycle without adding any detergent.

This should clear the unit of the excess detergent. If still the problem persists, then please check the following things--



1. Check the drain hose and make sure it is not plugged or kinked.
2. Unplug washer or disconnect power.
3. Check wire harness connections to the drain pump, pressure switch, and Central Control Unit (CCU).
4. Check/clean drain pump filter of foreign objects.
5. Plug in washer or reconnect power.
6. Check drain pump.
7. Check the pressure switch.
8. Verify CCU operation by running a Diagnostic Test or any cycle.



Please do accept the solution if the issue is resolved or post a comment for further assistance.



Thanks
Rylee

Aug 28, 2010 | Maytag Bravos MTW6600T Top Load Washer

1 Answer

What dos 5d means before the spin. When the time


Hi


Thanks for using FixYa. Error 5d means too much detergent was used. Try the following procedure---

Run the unit through a RINSE/SPIN cycle.
Run a NORMAL cycle without adding any detergent.

This should clear the unit of the excess detergent. If still the problem persists, then please check the following things--



1. Check the drain hose and make sure it is not plugged or kinked.
2. Unplug washer or disconnect power.
3. Check wire harness connections to the drain pump, pressure switch, and Central Control Unit (CCU).
4. Check/clean drain pump filter of foreign objects.
5. Plug in washer or reconnect power.
6. Check drain pump.
7. Check the pressure switch.
8. Verify CCU operation by running a Diagnostic Test or any cycle and replace the part that has gone bad.



Please do rate the solution if the issue is resolved or else revert for further assistance.



Thanks
Rylee

Aug 11, 2010 | Whirlpool Cabrio WTW6600SBT Top Load...

1 Answer

Error code 5d


Hi


Thanks for using FixYa. Error 5d means too much detergent was used. Try the following procedure---

Run the unit through a RINSE/SPIN cycle.
Run a NORMAL cycle without adding any detergent.

This should clear the unit of the excess detergent. If the issue is still not resolved then c
heck the drain hose and make sure it is not plugged or kinked. After this check wire harness connections to the drain pump, pressure switch, and Central Control Unit (CCU). Also check drain pump and pressure switch. Please do rate the solution if the issue is resolved or else revert for further assistance.


Thanks
Rylee

Jun 22, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Problem draining. Getting 5d code.


Hi


Thanks for using FixYa. Error 5d means too much detergent was used. Try the following procedure---

Run the unit through a RINSE/SPIN cycle.
Run a NORMAL cycle without adding any detergent.

This should clear the unit of the excess detergent. If still the problem persists, then please check the following things--



1. Check the drain hose and make sure it is not plugged or kinked.
2. Unplug washer or disconnect power.
3. Check wire harness connections to the drain pump, pressure switch, and Central Control Unit (CCU).
4. Check/clean drain pump filter of foreign objects.
5. Plug in washer or reconnect power.
6. Check drain pump.
7. Check the pressure switch.
8. Verify CCU operation by running a Diagnostic Test or any cycle.



Please do rate the solution if the issue is resolved or else revert for further assistance.



Thanks
Rylee

Jun 07, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Error code Sd (or 5d)


It means Suds Lock(Overdose of Detergent Detected During The Wash Cycle).If suds are detected continuously by the pressure switch during the drain or spin phases,the washer will fill 4 litres of water and during 5 minutes the unit will rest without tumbling,the water will be drained and it will try to spin or drain again.

If too much detergent was used:
– Run the unit through a Rinse/Spin cycle.
– Run a Normal cycle without adding any detergent.
This should clear the unit of the excess detergent.
1. Check the drain hose and make sure it is not plugged or kinked.
2. Unplug washer or disconnect power.
3. Check wire harness connections to the drain pump,pressure switch and Central Control Unit(CCU).
4. Check/clean drain pump filter of foreign objects.
5. Plug in washer or reconnect power.
6. Check drain pump.
7. Check the pressure switch.
8. Verify CCU operation by running a Diagnostic Test.

Apr 11, 2010 | Whirlpool Duet Sport HT WFW8400TE Washer

2 Answers

What does code F21 mean on a Kenmore HE2 plus washer 11047532602?


it stands for longer than normal drain interval,press "pause/cancel" twice to clear, if it returns then look for obstructions in the water drain from the basket all the way to the drain in the house,or possibly it could be a bad washer drain pump

Nov 19, 2009 | Kenmore HE2 Plus Front Load Washer

1 Answer

Code 5d comes on and it stops running


5d means the follow; possible causes * If too much detergent was used -Run the unit thrugh a RING/SPIN cycle. -Run a NORMAL cycle with out adding detergent. PROCEDURE * This should clear the unit of execess detergent. 1.- Check the draing hose and male sre it is not plugged or ****. 2 Unplug washer or disconnect power. 3.-Check wires harness connections to the drain pump, pressure switch, and center Cotrol Unit (CCU). 4.- Check/clean drain pump filter of foreign objects. 5-Plug in washer or reconect power. 6.- Check draing pump. 7.- Check the pressure switch. 8.- Verify CCU operation bu running a Diagnostic Test or any cycle. "Was this helpful?"

May 11, 2009 | Kenmore HE2 Plus Front Load Washer

Not finding what you are looking for?
Whirlpool Duet GHW9150P Front Load Washer Logo

1,520 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

prem mathew

Level 3 Expert

662 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...