Question about Kenmore Heating & Cooling

1 Answer

Hi my oven doesnt work anymore ! i change the fuse but nothing happen do i have to change the element in the oven ¸and how can i know which one i have to repair

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert whose answer got voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 147 Answers

Lets not get ahead of ourselves. Why did you change the fuse. If you put it on bake, the bottom element should come on, If you put it on broil then the top should come on. Does anything work on this oven. I think I would check the voltage at the receptical (outlet) where the oven plugs in. It should be 240 volts. Is this just an oven, has anyone been adjusting the clock or timer.

Posted on Nov 06, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have an electric admiral stove I tried changing the two 30amp fuses for oven but it still doesnt work. Would the problem be the heating element and where does one locate the element??

The oven element has probably failed. Im not sure about your Make of oven but the oven elements are either the coil type which are positioned around the oven fan at the rear of the oven or under the oven floor. The connections for either will be at the back of the oven.

Sep 30, 2015 | Kitchen Ranges

2 Answers

Miele 212 oven does not work. We have a Miele oven that does not work anymore. 220V gets to the oven and then nothing happens, no lights, no display, nothing... Advise anyone?

Nothing Works, or the Oven / Range / Stovetop Works Only At Certain Times:
1.Home breaker flipped or the fuse blown?Possibly an electrical surge has flipped the breaker. Check your breaker or fuse box and replace or reset as necessary.
2.Power cord plugged in?Grab the plug and wiggle to determine a good connection.
3.Power cord damage?Damaged rubber with wires showing through or the wire is being pinched can cause issues. Electrical tape is acceptable for covering damaged wires.
4.Aclicking sound could be something wrong with a relay. Check for any loose connections around the main control board on your oven. The click you hear is a relay losing power and switching back on. If the clock resets then something is causing power interruptions to the board.
6.Even a bad relay door switch will hinder your oven from operating.

If your oven has internal fuses, a wiring or component problem could have caused a fuse to blow. A blown fuse is an indication that a component has shorted or failed, and the problem will need to be corrected. Most ovens that use fuses will have an indication of the circuits that are affected by a particular fuse. If an oven fuse has blown, then you should inspect the oven element and the associated wiring to determine the cause before replacing the fuse.








May 18, 2015 | Miele Ovens

1 Answer

Hotpoint BD32 built in oven is not heating up anymore, top oven/grill works fine. When it's switched on it makes the right "noise" but there is no heat or light. Is this an element problem?

you can check the element, just get a volt ohm meter, set to ohm's and make sure it shows a short, otherwise you have an open or bad element.

Nov 06, 2013 | Ovens

1 Answer

AEG RIP? No power to oven?

If you have replaced an oven element the oven will not work again until you have reset the clock.

Sep 14, 2017 | AEG Ovens

1 Answer

Frigidaire Caprice Oven won't work

i have a double caprice oven and the top oven wont go - something to do with timers
can u help

May 12, 2009 | Frigidaire FEB27S5A Electric Single Oven

1 Answer


Pretty certain nofuse. Suspect switch. Guess would be as element blew it took out contacts on oven switch

Feb 20, 2009 | Bosch HBN 7052 GB Stainless Steel Electric...

1 Answer

Dryer doesnt work but i hear the timer working

Change your cycling thermostat. When your cycling thermostat fails, then the reponsibility of your heating element to shut down goes to the high-limit thermal shut off (closest to heat element) and the thermal fuse. Your cycling thermostat should shut down heat element when it detects about 140* air in the blower housing. Yours can't detect that anymore so it lets your dryer heat up and up till you blow the thermal. new cycling thermostat and thermal

Jan 18, 2009 | Kenmore 60172 Electric Commercial Dryer

2 Answers

Smeg oven not working

You have a element and or a faulty thermostat

Nov 25, 2008 | Smeg F170 Pyrolytic Stainless Steel...

1 Answer

Frigidaire Gallery Series

the control is bad and will have to be replaced, nothing need to happen for the eoc to fail i see them fail new out of the box

Apr 12, 2008 | Kitchen Ranges

Not finding what you are looking for?
Heating & Cooling Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Heating & Cooling Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers


Level 2 Expert

69 Answers

Are you a Kenmore Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides