Question about Kenmore 24 in. 15932 Built-in Dishwasher

1 Answer

Kenmore Ultrawash QuietGuard 3 Dishwasher not draining or rinsing

Hello:

Our Kenmore Ultrawash QuietGuard 3 Dishwasher is not draining completely at the tend of the cycle. If we press the "Cancel and Drain" button, it will drain, but it won't automatically drain at the end of the cycle. Also, i don't think it is washing or rinsing properly, as there is a white film on all the dishes. It looks like a hard water mark.

Thanks for any help you can offer.

Claire

Posted by on

  • 3 more comments 
  • clindsel Nov 05, 2008

    We are using rinse aid, but it is not removing the film since the dishwasher stopped draining properly. Where is the trap? It looks like the spray bar that rotates at the bottom of the dishwasher should come off, but it doesn't come off easily, and I didn't want to wreck it. Thanks.

  • clindsel Nov 05, 2008

    All dishes - top and bottom. i will have to get back to you about the model number - I couldn't find it when I looked this morning.

  • clindsel Nov 06, 2008

    I found a Part # 8269644.

  • clindsel Nov 06, 2008

    I found a part # 8269644.

  • naker Nov 07, 2008

    Please help - I have the same problem with my kenmore dishwasher. It is not draining properly and the dishes have a film on them.

    Model # 66517364300

    thank you

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 324 Answers

Hi Claire,
Are you using rinse aid?
that may help with the film.you may also have stuff down in the trap causing the water to drain slow.

Posted on Nov 05, 2008

  • 1 more comment 
  • is it the top and bottom dishes? what is the model # should start with 665

  • the model # should be when you open the door right on the right hand side



  • the model # should start with 665 i will see the dishwasher you have so i can tell you where the filter is.
    it could start with 363,


×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kenmore Quietguard 2 dishwasher not filling.


There is a solenoid that keeps the water in the washer. It is either faulty or there is something preventing it from closing completely. If there is no power applied to the washer, does it then hold water?

Apr 28, 2010 | Kenmore 24 in. 17002 Built-in Dishwasher

1 Answer

Hello, i have a Kenmore Quietguard standard dishwasher. it is in the "lock" position under dry options and the dishwasher will not start. can you tell me how i might be able to re-start this?


On our Kenmore Quietguard the lock light is at the Air Dry button. Holding the Air Dry button for about 8 seconds turns the lock light off if it is on and on if it is off.

Jan 04, 2010 | Kenmore Dishwashers

1 Answer

Kenmore Ultrawash Quietguard Deluxe Problem


kenmore washers nothing but problems, my washer says clean and will not do any cycles...... less that 2 years old

Oct 21, 2009 | Kenmore Dishwashers

1 Answer

Kenmore Ultrawash Quiet Guard 5 making buzzing/grinding noise


I have a very similar dishwasher, with a very similar problem. I fixed it by removing debris from the water evacuator pump located towards the front of the bottom of the machine (the last motor before the drain hose. In my case, grape stems had clogged it up. Once emptied, it purrs once again. NOTE: don't disassemble the motor, just flush it out, there is an o-ring gasket that is a bear to re-install.

Jun 22, 2009 | Kenmore 24 in. 15689 Built-in Dishwasher

1 Answer

Dishwasher Clean light blinks constantly.


Try turning off the power to the dishwasher at the circuit breaker box. leave the power off for 5 10 mins and then turn breaker back on and try to restart dishwasher. This may reset the board and it may work

Feb 05, 2009 | Kenmore 16602 / 16604 / 16609 Built-in...

5 Answers

Kenmore Ultrawash QuietGuard 3 Dishwasher not draining or rinsing


Not draining may either need new drain motor. or something is blocking the drain pipe.

Spots on dishes means you are using to much detergent or the wrong kind of detergent.

Your owners manuel should tell you what type to use.

Nov 18, 2008 | Kenmore 24 in. 15932 Built-in Dishwasher

1 Answer

Kenmore Quietguard Plus/Ultrawash - Kenmore


drain hose may be partially clogged or kinked up. ensure that the hose is not bent up thus restricting the flow of water out.

Nov 26, 2007 | Kenmore 16602 / 16604 / 16609 Built-in...

1 Answer

Kenmore Dishwasher Problems


Just for the degergent item.....The Sears repairman told me to not use the gel type detergent but only use cascade complete and to use very little of it..

Oct 19, 2007 | Kenmore 24 in. 16182 / 16189 Built-in...

Not finding what you are looking for?
Kenmore 24 in. 15932 Built-in Dishwasher Logo

1,085 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dishwashers Experts

D. E. Hev

Level 3 Expert

1167 Answers

Fred Sops

Level 2 Expert

272 Answers

Cindy Wells

Level 3 Expert

4946 Answers

Are you a Kenmore Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...